Instruction/ maintenance manual of the product SVR-480 Samsung
Go to page of 122
User Manu al 0.
User Manu al 1 Introduction Thank you for choosing Samsung DV R product s. This is the user manual for SVR-3200, SVR -1680C, SVR-1660C, SVR-16 45, SVR-960C, SVR- 945, SVR-480. Before inst alling or operating this product, please familiari ze yourself with this user manual and other ma nuals referenced by this manual.
User Manu al 2 incident. V arious experience an d technical is needed fo r inst allation of this product and an amateur installation m ight cause fire, electric shock, and defect. All instal lation operations should be performed by the agency you purch ased this product from.
User Manu al 3 Content s Chapter 1. Safety Cautions ............................................................ 7 1.1 Explaining the Symbols ................................................................................................... 7 Chapter 2.
User Manu al 4 4.6 Live Video Pause .......................................................................................................... 40 4.7 PTZ Control .........................................................................................
User Manu al 5 6.6.1 Audio .................................................................................................................. 68 6.6.2 Audio Mixing .......................................................................................
User Manu al 6 7.6 Playback .................................................................................................................. ........ 106 7.6.1 Screen Division & Channel Change ....................................................
User Manu al 7 Chapter 1. Safety Cautions 1.1 Explaining the Symbols Wa r n i n g Refers to information users need to know in order to prevent serious injury or death. Before installation V erify the supplied voltage (AC100V~AC240V) before connecting to the power supply .
User Manu al 8 Do not use water , paint thinner or organic solv ent for cleaning the product exterior . Doing so may cause a malfunction or an electric shock. Use a dry cloth to cle an the exterior . During inst allation For adequate ventilation, inst all the product with at least 15cm of sp ace between the cooler and the wall surface.
User Manu al 9 protection against harmful interfere nce when the equipment is operate d in a commercial environment. This equipment generate s, uses, and c an radiate radio frequency energy an d, if not installed an d used in accordance with the instructi on manual, may cause harmful interference to radio communications.
User Manu al 1 0 Chapter 2. Summary 2.1 Features Monitoring Screen The monitoring screen support s vivid, high-definit ion live visual feed from each channel and provides multiple screens.
User Manu al 1 1 Output - 1 in rear , SVR-960C/945 : 9 channels (4 RCA in rear , 5 D-SUB), Output - 1 in rear , SVR-480 : 4 channels (4RCA), Output – 1 in rear Supports simultaneou s recording and p.
User Manu al 1 2 backed up or stored to DV D-R, CD-R or a USB storage device. The built-in hard disk i s provided as primary storage Multiple porta ble data storage media are su pported: DVD-R, CD-R and USB ※ Refer to the appendix on the back of the manual regarding com patible media types.
User Manu al 1 3 Networking The product support s LAN, xDSL and other networki ng capabilities. Combined with the P C interface client, the core features of t he device can be easily remotely controlle d.
User Manu al 1 4 Chapter 3. Product Description 3.1 Front Part 3.1.1 SVR-3200 No. Classification Function 1 DVD-Multi for copying For copying recorded video and image s to DVD/CD optical media.
User Manu al 1 5 COPY lamp Indicates copying operation. PLA Y lamp Lit when copying. 1 1 Power button T urns on or of f the device. 12 ESC button The Escape button navigates up the menu tree and closes dialog windows. 13 COPY S tarts Copy mode. 14 FUNC S tarts F unction mode.
User Manu al 1 6 3.1.2 SVR-1680C, SVR-1660C, SVR-1645 No. Classification Function 1 DVD-Multi for copying For copying recorded video and image s to DVD/CD optical media.
User Manu al 1 7 closes dialog windows. 13 COPY S tarts Copy mode. 14 FUNC S tarts F unction mode. 15 MONITOR Cycles through from Monitor 1 to 4 : SVR-168 0C, Switches from main and sub monitor : SVR-166 0C, SVR-1645 16 PTZ S tarts or ends PTZ function.
User Manu al 1 8 3.1.3 SVR-960C No. Classification Function 1 DVD-Multi fo r copying For copying recorded video and image s to DVD/CD optical media. 2 Channel LED Shows the data input and ev ent operation status 3 Channel button Selects chan nel in live feed or playback 4 AUTO S tarts or stop s user defined sequence s.
User Manu al 1 9 14 MONITOR Switches from main and sub monitor 15 PTZ S tarts or ends PTZ function. 16 USB1, USB2 USB ports for extern al devices (mouse, USB memory stick). 17 PLA Y/ENTER S tart playback or select an item on the menu. 18 ◀ /REW Navigates or selects i n t he menu, or for playback, changes the reverse playback speed.
User Manu al 2 0 3.1.4 SVR-945 No. Classification Function 1 Channel LED Shows the data input and ev ent operation status 2 Channel button Selects chan nel in live feed or playback 3 AUTO S tarts or stop s user defined sequence s. 4 MUL TI Changes split-scre en sections for live video feeds or playback.
User Manu al 2 1 14 PTZ S tarts or ends PTZ function. 15 USB1, USB2 USB ports for extern al devices (mouse, USB memory stick). 16 PLA Y/ENTER S tart playback or select an item on the menu. 17 ◀ /REW Navigates or selects i n t he menu, or for playback, changes the reverse playback speed.
User Manu al 2 2 3.1.5 SVR-480 No Classification Function 1 DVD-Multi fo r copying For copying recorded video and ima ges to DVD/CD optical media. 2 Channel button Selects chan nel in live feed or playback 3 Channel LED Shows the data input and event operation st atus 4 AUTO S tarts o r stops user define d sequences.
User Manu al 2 3 dialog windows. 13 COPY S tarts Copy mode. 14 FUNC S tarts Fun ction mode. 15 MONITOR Switches from main and sub monitor 16 PTZ S tarts or en ds PTZ function. 17 PLA Y/ENTER S tart playback or select an item on the menu. 18 ◀ /REW Navigates or select s in the menu, or for playback, changes the reverse playback speed.
User Manu al 2 4 3.2 Rear Part 3.2.1 SVR-3200 No. Input/Output terminal name Function 1 POWER IN Socket for AC 100V ~ AC 240V power cord. 2 CH1 ~ 32 Connection terminal for camera BNC in put. 3 MONITOR 1 ~ 4 Connection termin al for monitor BNC output.
User Manu al 2 5 15 AUDIO IN(D-SUB) Connection te rminal for audio output D-SUB. 16 D-I/O Connection terminal for DIGIT AL IN/OUT . 3.2.2 SVR-1680C, SVR-1660C, SVR-1645 No. Input/Output terminal name Function 1 POWER IN Socket for AC 100V ~ AC 240V power cord.
User Manu al 2 6 15 SENSOR IN Connection terminal for sensor input. 16 AUDIO IN(D-SUB) Connection te rminal for audio output D-SUB. 17 D-I/O Connection terminal for DIGIT AL IN/OUT . 3.2.3 SVR-960C No. Input/Output terminal name Function 1 POWER IN Socket for AC 100V ~ AC 240V power cord.
User Manu al 2 7 15 AUDIO IN(D-SUB) Connection te rminal for audio output D-SUB. 16 D-I/O Connection terminal for DIGIT AL IN/OUT . 3.2.4 SVR-945 No. Input/Output terminal name Function 1 CH1~9 Connection terminal for camera BNC input. 2 LOOP OUT Connection terminal for camera BNC output (loop ).
User Manu al 2 8 15 GROUND Ground termi nal between DVR and external device. 16 POWER IN Socket for AC 100V ~ AC 240V power cord. 3.2.5 SVR-480 No. Input/Output terminal name Function 1 GROUND Ground terminal between DVR and external d evice. 2 CH1~4 Connection terminal for camera BNC input.
User Manu al 2 9 Refer to det ailed description for inst allation & use fro m “Install Manual”. 3.3 OSD MENU structure The menu structure is as shown belo w.
User Manu al 3 0 3.4 Function Menu The function menu allo ws the users to access any and a ll f unctions and operations of th e product with the mouse. To execute a particular functi on, left-click the icon. Also, all f unctions listed in the function menu can be executed in full-screen mode.
User Manu al 3 1 MM/DD/YYYY Current time Display Setup Channel Display Channel Number Ch1 Title Cam 1 Status Enable Color Color AGC Enable Brightness 0 Contrast 0 Monitor Monitor Number Main Monitor (Monitor 1) Covert Channel Deselect All Sequencing Number 1 is set to Channel 1 and Number 2 is set to Channel 2 in orde r.
User Manu al 3 2 Channel Audio Mix Mix On Program A~Z ¡¡ CIF , 0f ps, Q1 Event Setup Event Event Check Always Event Screen /Dwell time Monitor 1 Off Event Action Relay 1 Action Duration 10 sec. Normal Event Source Deselect All System Event Source Deselect All Normal Event MD Ch1 MD Sensitivity 2 Area Set All Sensor N.
User Manu al 3 3 IP addr Default IP Net Mask Default NM Gateway Default GW DNS1 0.0.0.0 Additional DNS 0.0.0.0 Port 4000 BandWidth Limit(Mbps) 0 xDSL User ID ¡¡ guest Password ***** Status xDSL not connected. Port 4000 Bandwidth Limit (Mbps) 0.0 DDNS Interval Off Server www.
User Manu al 3 4 Default >> Load/Save Configuration Load, >> Firmware Update >> DVR Alias DVR0 System Log >> I-Frame Interval Auto Time >> Disk Disk Manager >> Disk.
User Manu al 3 5 Record Program Model SVR-1660C/1645 SVR-960C/945 Mode Normal Event Normal Event Res Fps Q Res Fps Q Res Fps Q Res Fps Q Program A D1 7 Q5 D1 7 Q5 D1 7 Q5 D1 7 Q5 B D1 5 Q5 D1 7 Q5 D1 .
User Manu al 3 6 Program B D1 20 Q5 D1 30 Q5 D1 10 Q5 D1 15 Q5 C D1 20 Q4 D1 30 Q5 D1 10 Q4 D1 15 Q5 D D1 15 Q5 D1 15 Q5 D1 7 Q5 D1 7 Q5 E D1 20 Q4 D1 30 Q5 D1 10 Q4 D1 15 Q5 F D1 15 Q4 D1 15 Q4 D1 7 .
User Manu al 3 7 Chapter 4. Monitoring When power is supplied to the DVR, images from all channels connected via analog are displayed on the screen in monitor mo de. This c hapter describ es all DVR features in monitor mode. 4.1 Default Display - The DVR automatically powers on when the power cord is plugged in.
User Manu al 3 8 menu. T o stop this feature, press the button again or click Auto t o toggle it in the Function menu. 4.4.1 Default System Mode - Use the button to automatically convert the set channels. - Press the [MENU] button to set the dwell time.
User Manu al 3 9 1. Up to 16 user modes can be defined. 2. In the image above, 6 sequences are define d with single screen (1) Æ full screen (16DIV) Æ 4 channel split-screen (4A) Æ si ngle screen (5) Æ single screen (6) Æ 9 channel split-sc reen (9A) all being display ed in sequence.
User Manu al 4 0 1. If Event Screen is set to Off, event popup s w ill not work. 2. If Event Screen is set to On, th e popup image remains displayed until a button is pressed.
User Manu al 4 1 4.7 PTZ Control Y ou can control PTZ while watching a video in real time by connecting the PTZ controller with the DVR an d setting the protocol from the "Serial" menu. Y ou can either press the PTZ bu tton on the front or press the [Func] button to execute PTZ.
User Manu al 4 2 To k i n a T O K I N A Kodicom KRE KODICOM Nuvico NUVICO - Press a channel button. - Press the [PTZ] button on the front or click the button on the Function menu. - The PTZ menu (Pan/T ilt, Zoom/Focus, Load Preset, Save Preset) will appear .
User Manu al 4 3 4.7.6 Auxiliary Off This is to stop special functions of a PTZ device. - Use the up or down arrow key or the mouse wheel to set an Aux number . - Select Off and then press the [Enter] button or click. 4.7.7 Menu This is used to enter the consol e menu of t he connected PTZ device.
User Manu al 4 4 Chapter 5. Playback 5.1 Playback Mode 5.1.1 Playback on Default Display (16/9/4 channel split-screen) - Press the [PLA Y] button or click the button on the Function menu in monito ring mode. - Press the [PLA Y] button or the [FWD] button to play a video at the default 1x speed.
User Manu al 4 5 STEP FOR W ARD : Pressing the [FWD] button while p aused plays the video frame by frame. Press the [PLA Y] button to return to normal pl ayback. STEP REWIND : Pressing th e [REW] button while p aused plays the video frame by frame in reverse.
User Manu al 4 6 the end time. Search Button : Search the video for the specified date and time. 5.2.2 Calendar Search Y ou can search videos more easily with the calendar .
User Manu al 4 7 St art-REC Time : Display the date and time when the recording started. End-REC T ime : Display the date and time of the latest recordin g.
User Manu al 4 8 Channel : Select a channel. Use th e up or down arrow key on the front or the mouse wheel to change the value. Star t Tim e : Enter a start date and time to st art the search from. Use the left or right arrow key to go to an item, press the [Enter] button and use the up or down arrow key or th e mouse wheel to change the value.
User Manu al 4 9 The SVR-945 is not equipped with a DVD device so you must connect the unit with an external backup dev ice. Connect an external backu p device to the USB or eSA T A port, execute copy and select CD/DVD. On the media list, a CD/DVD devi ce whose type is [Ext] is display ed.
User Manu al 5 0 For more information on support me dia, refer to the table below . DVD-R Maker CD-R Maker Mitsubishi (16x recommen ded) Mitsubishi (16x recommended) TDK (16x recommended) TDK (16x recommended) Imation (16x recommended) Imation (16x recom mended) Sony (16x recommended) Sony (16x recommended) 5.
User Manu al 5 1 [Enter] button or click to select a media. Star t : S tart copying. Move to the [S tart] button and press the [Enter] button or left-click. F A T32 Format : Format unformatted USB stora ge devices or HDDs in F A T32 before copying. Select the [F A T32 Format] button and press the [Enter] button or left-click.
User Manu al 5 2 [Enter] button or click to select media. Star t : S tart copying. Move to the [S tar t] button and press the [Enter] button or left-cli ck. F A T32 Format : Format unformatted USB storage devices and HDDs in F A T32 before copying. Select the [F A T32 Format] button and press the [Enter] button or left-click.
User Manu al 5 3 Chapter 6. Setup 6.1 Record Setup There are 4 DVR recording modes. Their relatio nship is as shown in the image below , which briefly describes recording modes. For more information on recording, refer to the following sections. 6.2 Time Setup Y ou need to set the system time before setting recording.
User Manu al 5 4 not recommended to change the time while recording . The factory default time zone is UTC 00:00 Dublin. 6.2.1 How to Set Time If you change the time when recording is already in progress, the time is also changed for existing rec orded videos.
User Manu al 5 5 Apply Y ou must press the [Apply] button to save t he Date/T ime values. Then, the dialog box below appears. Setup s other than "Date/T i me" setup are automatically recorde.
User Manu al 5 6 6.3.1 How to Set a Camera Press the [MENU] button and use t he navigation keys or the mouse wheel to select a desired channel from the "Channel" menu und er the "Display" menu of Display Setup. Ti t l e S pecify the camera name.
User Manu al 5 7 Press the [Enter] button and use the left or ri ght arro w key or the mouse wheel to select "Enable" or "Disable".
User Manu al 5 8 Monitor 1 is available for all su pported functions of the DV R while Monitor 2 is available for event popup, user sequencing and split screen. Covert Channel This menu is used to hide cha nnels in live mode. The Covert Channel menu sh ows the unit's cha nnel list.
User Manu al 5 9 6.5.1 Program Setup Using the [Program] menu, you can set up a pro gram to use for both Manual & Event and Schedule & Event. Y ou can adjust the frame rate , video quality and resolution of the program.
User Manu al 6 0 Q (Quality) Indicates the recording quality: Q5, Q4, Q3, Q2, and Q1. For Event Recording, Q3 or higher is recommended. Max R/F Indicates the maximum frame rate available for a sel ected resolution. For instan ce, CIF 30fp s means that you can select up to 30fp s for the CIF resolution of a selected channel.
User Manu al 6 1 • Event Settings in and CIF 480f p s Recording Performance When every channel is set up to record norma lly at CIF 30fp s, the Event Recording settings of for 1 st channel are limited to CIF 30 fp s, Half 15 fp s, and D1 7fp s.
User Manu al 6 2 Schedule & Event Setup Set record mode to "Schedule & Event" and set a schedule and e vent for each date and time. How to Check Recording If record setup is properly completed, the 'REC LED' on the front w ill flicker .
User Manu al 6 3 Manual Recording Manual Recording is activa ted only when the recording mode is set to Manual & Event. Af ter selecting a program, press the [REC] button on the front of the DVR unit to begin recording. If you want to schedule a recording, switch the recordi ng mode to Schedule & Event.
User Manu al 6 4 • Index: 1~50 dif ferent programs can be set • Day: designate recording date • Program: select a recording pro gram (A~T) • T ime: designate recording time • Delete: delete the desired INDEX Setting Method As you set INDEX, DA Y , PROGRA M and HOUR, then the content will be immediately display ed in the table.
User Manu al 6 5 When you set the region of time, you may not include the existing time that is set previously . Record Setting Repeat Record Mode When there is no more sp ace for recording to hard disk, reco rded data is removed from the foremost portion automatically .
User Manu al 6 6 Event Recording is used mostly in conjunctio n with other recording options: Manual & Event and Schedule & Event. Go to [Record Setup] > [Record]. In "Record Mode," select Ma nual & Event or Schedule & Event.
User Manu al 6 7 • INDEX : 1~50 different p rograms can be set • Day: designate recording date • T ime: designate recording time • Delete: delete the desired INDEX Setting Method As you set INDEX, DAY, and HOUR, then the content will be immediately displa yed in the table.
User Manu al 6 8 6.6 Audio Setup This menu is used to set audio re cording, sync or mixing. 6.6.1 Audio This menu is used to set the audio cha nnel, audio recording, audio gain and sync. Audio Channel Select a channel for audio. Audio Recording Decide whether to reco rd audio.
User Manu al 6 9 6.6.2 Audio Mixing This menu is used to sele ct audio for live video feeds. If All is set, all inputted audio is mixed for output regardless of channel sele ct ion. If specific audio is selecte d, only the specified channel is outputted regardless of the channel sele ction.
User Manu al 7 0 Motion Detection This enables each channel or all channels to detect motion and notify users. - Channel Channel can be set to All or as follows. SVR-3200: 1~32CH SVR-1680C/1660C/1645: 1~16CH SVR-960C/945: 1~9CH SVR-480 : 1~4CH - Sensitivity Sensitivity can be set to Lowest, 1~10, or Highest for each ch annel.
User Manu al 7 1 detection areas turn gray . T o select motion detection area s, use the navigation buttons to sel ect them and press the [Enter] button or click them. Pr ess the [ESC] button or right-click to return to the previous menu. Sensor A total of 16 sensors (9 senso rs for the SVR-960C/945, 4 senso rs for the SVR-480) can be set.
User Manu al 7 2 Lines This defines the maximum numbe r of lines for one piece of data. An external device may not be recog nized depending upon it s characteristics, so it is recommended to cont act the manufactur e r before inst allation. 6.7.2 Preset This menu is used to activate the preset s specified in the PTZ based on sensor input.
User Manu al 7 3 6.7.3 Digital I/O Digital I/O are digit al ports available for input and out put at the same time., There are 12 digital inputs and o utputs.
User Manu al 7 4 6.7.4 Event Action This set s actions based on event input. Event Action For Event Action, you can select Relay 1~4, buzzer , or E-Mail. Action Duration Action Duration is used to maint ain an action for a specified time when relay or buzzer is set.
User Manu al 7 5 System Event Source This set s some or all of disk error , disk fu ll, fan error , authentication failure and DDNS registration failure. E-Mail Setup E-Mail address is set when e-mail i s used for output. For e-mail address, enter an e-mail a ddress for a message recipient .
User Manu al 7 6 - Att aching Image Files For a Normal event log, the system send s an e-mail atta ched with an image of the event channel along with the event information in cluding the sensor , movement detection, and object disappearance.
User Manu al 7 7 This is used to select the network type (Etherne t/xDSL) conn ected to the DVR. Select Ethernet when the DVR is connected to dedicate d line, cable modem or LAN. Select xDSL when the DVR is connected to a PPPoE-type xDSL line. However, if the xDSL line is not of the PPPoE type, you must select Ethernet.
User Manu al 7 8 Port is used to register to SWR, connect to Network Manager, or con nect to Webviewer. The default port is 4000. Be careful a bout the port entry when a PPPoE modem Internet sharing device are in use.
User Manu al 7 9 server , the DVR's IP may be identified by connecting to the DDNS server . T o register a dynamic IP address to a DDNS, follow the instructions shown belo w . DDNS Registration procedure 1) Sign up at iPOLiS homepag e. - The home page URL is [www .
User Manu al 8 0 - Product List (If you didn’t register p roducts, there are no list) - Product Registration ( Check ID av ailability ), Information regarding the registered products may be reviewed.
User Manu al 8 1 3) Configure the product for DDNS From the DVR's Networ k Setup menu, configur e the settings as shown below . Select Menu and Network to prompt a screen similar to the illu stration shown bel ow . Set DDNS to "On" and input the DDNS address in 'DDNS SER VER DOMAIN NAME'.
User Manu al 8 2 - The Produ ct list will display status 'On' for the conne cted device [VIEW]: See the log-in pag e of selected product [Edit]/ [Delete]: Edit/Delete the selected product Once the product has been regi stered, its ID (domain) may not be changed.
User Manu al 8 3 A dynamic IP address will renew the relevant dat a from the DDNS per each interval. If the user sets the registration interva l to "Disabled" or the DVR does not upload any information over two days, information regarding the DVR will be removed from the DDNS database.
User Manu al 8 4 This turns NTP on or off. NTP Mode This set s NTP Mode to Client, Server or All. NTP Serv er Location This is enabled when NTP Mode is set to Client.
User Manu al 8 5 Remote Controller ID Up to 16 remote controller IDs can be set. Y ou can use one remote controller t o operate up to 16 DVRs. How to register the remote controll er is as shown below . - Direct the remote controll er to the DVR. - Press the [ID] button based on the specified remote co ntroller ID.
User Manu al 8 6 6.8.4.1.1 T ext T o use the T ext option, please follo w the instructions below . Please note that the T ext option suppo rts only Co m1 (RS-232); make sure to select Com1 on the Serial Port menu. Device Select T ext. Interface Select RS-232.
User Manu al 8 7 Device Select a connected transpa rent device. Interface Select COM1 or COM3. ※ Only Com1 is available for SVR-480. Baud rate/Parity/S top Bit/Dat a Bit Enter the same settings as the ones for the selected Transp arent device. 6.8.4.
User Manu al 8 8 Select COM1 or COM3. ※ Only Com1 is available for SVR-480. Baud rate/Parity/S top Bit/Dat a Bit Enter the same settings as the ones for the selected keyboard. 6.8.4.1.4 PTZ Select PTZ. To control the PTZ operation via serial port, sele ct PTZ in the Device options, and then set up a serial port; refer to 6.
User Manu al 8 9 6.8.4.2.1 PTZ(Coax) The Coax Protocol option does not su pport normal PTZ protocols, but rather su pports the Pelco S tandard and Extended Protocols.
User Manu al 9 0 Ty p e Select a serial port. Protocol Select a connected PTZ dev ice. Camera ID Enter the ID of the selected camera. Interface Select one from among Com2 to 4. T o use RS-232, select Com3. For RS-42 2 or 485, select Com2 or 4. Baud rate/Parity/S top Bit/Dat a Bit Enter the same settings as the ones for the PTZ device.
User Manu al 9 1 6.9.1 System Setup Language The OSD menu support s multiple languages. Select a language. Key Buzze r This determines whether to use the buzzer for the butt ons on the front. Default This restores the factory de fault settings. Press the [Default] button to rest ore the fac tory default.
User Manu al 9 2 password (default: 1 1 1 1 1 1 1 1) specified in SNM-128S into "Admin Password" and press th e [S t art Upgrade] button. After the upgrade p rogress window appears, a message prom pting you to reboot the unit is displayed. Select "Y es" to reboot the unit.
User Manu al 9 3 Copying System Log System logs are saved as txt-formatted f iles, and can be saved to a USB flash drive. T o save system logs to a USB drive, insert t he drive into a USB port, open the System Log list. And then press the "COPY" button on the front.
User Manu al 9 4 Disk Manager Disk Manager is used to manag e internal and external HDDs. It manages HDD st atus, bad blocks, size, enabled, disabled, etc. Ty p e : Displays disk locations and types. Int A (Internal A HDD), Int B (Int ernal B HDD), Ext (External HDD) Model : Displays HDD models.
User Manu al 9 5 Size(MB) : Displays HDD si zes in MB. Enabled : Enables or disables HDDs. Y es: Enabled / No: Disabled T o change HDD to Y es - Enabled : Select No and press the [Enter] button or use the mo use wheel to open the notice window with the following messag e.
User Manu al 9 6 features without any limit ations. The maximu m number of u sers is 10. They can only use features that they have permissions for . Right In Right Setup, if Check is set to all X, all users can use all features without any limitations.
User Manu al 9 7 10's password is "000 00000". The 16 channel-DV Rs do not have a [0] (zero) button so they use the [10] (ten) button instead. Change Pass w ord As shown in the image below , click Change P/W for a user you want to change.
User Manu al 9 8 Save This saves all settings and exit s to the live screen. Select Y es to save all settings and exit, or se lect No to exit without saving any settings.
User Manu al 9 9 Chapter 7. W eb V iewer Web V iewer is a web ap plication provided as a co mplement for the DVR, cap able of receiv ing visual live feeds and playing recorded dat a from a distance ov er the Internet. Web V iewer's structure consist s of the log-in page, moni toring monitor and playback monitor .
User Manu al 100 7.3 Connection User setup T o log into Web V iewer , the user ID and password m ust be entered to Network Manager's Configuration T ool. Up to 1 administrato r and 10 regular user IDs and passwords may be issued. For security purposes, the administrator and regular passwo rds must be distinct.
User Manu al 101 After the account s have been configured, assign aut hority levels for each account. T o allow playback access, check "Hard" under th e user's account in Configuration T ool. Also, to allow accesses to "Microphone", "PTZ", "Relay", et c.
User Manu al 102 Double-click the ch annel to expand into Single p artition mode. The screen will expand into Single pa rtition. T o return to the partition screen, double-click the monitoring area once a gain. In a partition mode, the pla cement of screens may be moved around.
User Manu al 103 7.5.4 Sensor indication This icon indicates that a sensor has been trigge red. When triggered, it s corresponding icon will turn red and the sensor ID number will be displaye d on the video. Sensors that have not been triggered will remain blue.
User Manu al 104 7.5.7 Event Data A real-time log of event informa tion is displayed below the monitoring p age. Items found in this log are as shown below . (T able Event Icon) Button Function Change setup Motion detection Sensor , Relay On V -loss T ext Input User Login 7.
User Manu al 105 from and select "Save As". T o confirm the savi ng operatio n, go to the directory the image is saved to and double-click the image. 7.5.9 PTZ Use While monitoring, right-clicking o n a channel supporting PTZ and selectin g "PTZ" will allow the user to manipulate the camera position.
User Manu al 106 7.5.10 Audio Use If a channel is paired with an audio channel, right-clicki ng the visual and selecting "Listen" from the pop-up menu will activ ate audio input. Also, to listen to the audio signal, Mute also needs to be unchecked.
User Manu al 107 Playback support s 1, 4, 9 and 16 Partition mode s. Use the menu (shown above) at the top of the page to choose a p artition mode. When t he monitoring screen is displaying Channel 1 through 4 in 4 Partition mode, cli cking ">>" butt on will displ ay the next four channels.
User Manu al 108 is On. Deactivated channel buttons are not supported by the DVR model. 7.6.6 Recording Du ration & Recording Siz e Check This menu displays used and remai ning spaces in the HDD. It also displ ays the total recording duration. HDD usage is ex pressed as a percent age.
User Manu al 109 T rouble Shooting 1. DVR is not booting up z Check the power sup ply z Check the power co rd 2. Monitor won’t display anything z Check the monitor ’s po wer supply z Check the con.
User Manu al 1 1 0 z Check the remote’s ID z Check the remote’s specification 8. The buttons aren’t worki ng z Check the DVR’ s power supply z Check the Screen Lock setting 9.
User Manu al 1 1 1 Comp atible HDD List Seagate T echnology W estern Digit a l Capacity Model Capacity Model 1000GB ST31000340SV 1000GB WD10EVCS 750GB ST3750840SCE 750GB WD7500A VCS 500GB ST3500830SCE.
User Manu al 1 1 2 Resolution 704x480 NTSC, 704x576 PAL Multi Screen SVR-3200/1680C/1660C/1 645 : 1/4/9/10/16 SVR-960C/945 : 1/4/9 SVR-480 : 1/4 Performance Recording Compression MPEG-4 Record Rate/NT.
User Manu al 1 1 3 SVR-1660C/1645/960C/945/480 : 9 Mbps Bandwidth control Automatic Multi Stream MPEG-4(Dual Streams)/JPEG Remote Users Up to 10 simultaneous users Protocol support TCP/IP, DHCP, DNS, .
User Manu al 1 1 4 Sampling rate 16 kHz Alarm Inputs SVR-3200/1680C/1660C/1 645 : 16 Input, NO/NC SVR-960C/945 : 9 Input SVR-480 : 4 Input Outputs Screw terminal 4 relay out puts, NO/NC (SVR-480 : Scr.
User Manu al 1 1 5 Portuguese, Russian, Turkish, Japane se, Czech, Serbian, Swedish, Rumanian, Danish, Chine se, Korean, Taiwanese.
User Manu al 1 1 6 Dimensions SVR-3200, SVR-1680C, SVR-1660C, SVR-1645.
User Manu al 1 1 7 SVR-960C.
User Manu al 1 1 8 SVR-945.
User Manu al 1 1 9 SVR-480.
User Manu al 120.
User Manu al 121.
An important point after buying a device Samsung SVR-480 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samsung SVR-480 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samsung SVR-480 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samsung SVR-480 you will learn all the available features of the product, as well as information on its operation. The information that you get Samsung SVR-480 will certainly help you make a decision on the purchase.
If you already are a holder of Samsung SVR-480, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samsung SVR-480.
However, one of the most important roles played by the user manual is to help in solving problems with Samsung SVR-480. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samsung SVR-480 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
