Instruction/ maintenance manual of the product SSA-R2001 Samsung
Go to page of 18
RFID Reader User Manual SSA-R2001 imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website.
2_ Safety information safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE.
English 3 SAFETY INFORMATION Keep out of direct sunlight and heat radiation sources. It may cause fi re. Install it in a place with good ventilation. Avoid aiming the controller directly towards extremely bright objects such as sun.
4_ Contents contents PRODUCT INTRODUCTION 5 5 Features 5 What’s included 6 At a Glance 7 Cable Color Scheme 7 Cable Selection INSTALLATION AND EXTERNAL CONNECTION 8 8 Installation 9 Precautions on i.
English 5 PRODUCT INTRODUCTION FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10cm (4”) read range. It is also supported by backlighting on the keypad, enabling stable operation at night.
6_ Product Introduction product introduction AT A GLANCE Front/Rear 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 2-PIN Connector Can be connected to the power cable. 4 6-PIN Connector Can be connected to Wiegand, RS-232 communication cables.
English 7 PRODUCT INTRODUCTION CABLE COLOR SCHEME 2-PIN Connector I/O Pins Signal Cable Color Power (+12V) DC +12V Re d Earth-grounding GND (-) Black 6-PIN Connector I/O Pins Signal Cable Color Wiegan.
8_ Installation and External Connection installation and external connection INSTALLATION Attach the provided rear panel to the wall and drill two 6-32 holes and one 1/2 inch hole on it. (See [Figure 1]) Refer to [Figure 2] below on how to secure the rear panel to the wall using the provided screws.
English 9 INSTALLATION AND EXTERNAL CONNECTION PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below.
10_ Installation and External Connection installation and external connection EXTERNAL CONNECTION WIRING DIAGRAM Category Cable Color Power Supply Unit Connect the DC+12V to the red line. Connect GND to the black line. Wiegand Connection Connect the green line of the product to the Wiegand D0 input port of the controller.
English 11 INITIALIZATION initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 34bit Wiegand. Adjust the format according to the controller receiving the keypad input. To change the output format, use the switch on the rear of the product.
12_ Initialization initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on.
English 13 OUTPUT FORMAT output format WIEGAND OUTPUT Timing Diagram Data Format (34-bit) Bit 1 : Even Parity (bit 2 ~ bit 17) Bit 2~Bit33 : 4-byte ID Number Bit 34 : Odd Parity (bit 18 ~ bit 33) • .
14_ Output Format output format RS-232 OUTPUT Output Waveform Data Type START (0X02H) DATA (10 Char) END (0x03H) LRC START(0X02H) DATA (10 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC : This is the result of XOR operation of each byte from Start to End.
English 15 OUTPUT FORMAT 4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 7 2 0010 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 E.
16_ troubleshooting troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. PROBLEM SOLUTION My card is not read properly.
English 17 product specifi cations PRODUCT SPECIFICATIONS Item SSA-R2001 Power / Current DC 12V / Max.75mA Reading Time (Card) 30ms Input Port 2 ea : External LED Control, External Buzzer Control Out.
AB82-02555A Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life.
An important point after buying a device Samsung SSA-R2001 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samsung SSA-R2001 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samsung SSA-R2001 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samsung SSA-R2001 you will learn all the available features of the product, as well as information on its operation. The information that you get Samsung SSA-R2001 will certainly help you make a decision on the purchase.
If you already are a holder of Samsung SSA-R2001, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samsung SSA-R2001.
However, one of the most important roles played by the user manual is to help in solving problems with Samsung SSA-R2001. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samsung SSA-R2001 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
