Instruction/ maintenance manual of the product PCA-6189 Samsung
Go to page of 144
PCA-6189 Full-sized PCI/ISA-bus socket 479 Pentium® M/ Celeron® M processor-based CPU card User ’ s Manual.
PCA-6189 User’s Manual ii Copyright Notice This document is copyrighted, 2005, by Advan tech Co., Ltd. All rights are reserved. Advantech Co ., Ltd. reserves the right to make improve- ments to the products descri bed in this manual at any time withou t notice.
iii 1.0.1 A Message to the Customer Advantech customer services Each and every Advantech pro duct is built to the most exacting specifica- tions to ensure reliable performance in the harsh and demanding condition s typical of industrial environ ments.
PCA-6189 User’s Manual iv T able 1.1: PCA-6189 comparison table Model PCA-6189VE-00A2 PCA-6189VG-00A 2 PCA-6189G2-00A2 PCA-6189F-0 0A2 VGA: Intel 855GME integrated Ye s Ye s Ye s Ye s USB 2.
Table 1.2: PCA-6189 DDR memory compa tibility table V endor Size S peed T ype ECC Model Memory Apacer 256MB DDR266 DDR N 77.10603 .1 12 Infineon HYB25D25680B T -7(32×8) Kingston 256MB DDR266 DDR N NA.
PCA-6189 User’s Manual vi Sam- sung(DSL) 512MB DDR400 DDR N NA SAMSUNG K4H560838F- TCCC(32×8 ) Kingston 256MB DDR400 DDR N KVR400 X64C3/ 256 Hynix HY5DU56822BT - D43(32×8) UG 1GB DDR266 DDR N NA Hynix HY5DU128822A T- H Apacer 512MB DDR333 DDR N 77.
vii * PCA-6189 only supports DDR333 RAM. If DDR400 RAM is used, it will op erate at the speed of DDR333 DSL 256MB DDR400 DDR N NA Hynix HY5DU56822BT - D43 256MB DDR400 DDR N NA SAMSUNG K4H560838E- TCC.
1.0.1 Product warranty Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in material s and workmanshi p for two years from the date of purchase.
ix 1.0.2 Initial Inspection Before you begin i nstalling your single board co mputer , please make sure that the following materials hav e been shipped: If any of these items are missing or damaged, contact your distributor or sales representative immediately .
PCA-6189 User’s Manual x 1.0.3 Release Note Date Revision Description December 2004 1st. Edition Initial Release.
xi Important Safety Informati on SAFETY INSTRUCTIONS This device complies with the requirements in p art 15 of the FCC rules: Operation is sub- ject to the following two conditions: 1.
PCA-6189 User’s Manual xii.
xiii Contents Chapter 1 Hardware Co nfiguration ................................. 2 1.1 I ntroduction ............ ............................ ............ ........... ........ 2 1.2 Features ........................ .............. .............. ...
PCA-6189 User’s Manual xiv 2.5 USB Ports CN6, CN31, and CN32 ............. .............. ...... 21 2.6 VGA Connector CN7 ........... .............. .............. ............... 22 2.7 LVDS connector VCN2 ..................... .............. .....
xv 3.4.14 Typematic Dela y (msec) .......... ........... ........... ............. .. 35 3.4.15 Security Option .......... ........... ............ ............. ........... .... 36 3.4.16 APIC Mode ..... ........... .............. ........... .......
PCA-6189 User’s Manual xvi 3.9.1 On-board FDC Controller .......... ............. ........... ........... 43 3.9.2 On-board Serial Port 1 ................. .............. ........... ........ 43 3.9.3 On-board Serial Port 2 ................. .......
xvii 3.13.1 Auto-detect P CI CLK ... ........... ........... ........... ........... .... 48 3.13.2 Spread Spectrum ........ ........... ............ ........... ........... ...... 48 3.14 Passwords and Settings .............. .............. .........
PCA-6189 User’s Manual xviii 10.1 I ntroduction ......... ................................................... ......... 94 10.2 Entering Setup ................... ............... .............. .............. ... 94 Figure 10.1:RAID Setup i nitial screen .
xix B.13 External Speaker Connector (CN17)............................ . 117 Table B.13:External Speaker Connector (CN1 7) ....... 117 B.14 Reset Connector (CN18) ............ ................. .............. .... 118 Table B.14:Reset conne ctor (CN18).
PCA-6189 User’s Manual xx.
1 CHAPTER 1 General Information.
PCA-6189 User’s Manual 2 Chapter 1 Hardware Configuration 1.1 Introduction The PCA-6189 is designed with Intel® 855GME chipset and 6300ESB (I/O controller) to support the Intel ® Pentium® M / Cel.
3 1.2 Features 1. Supports FSB 400 MHz low thermal pro file Intel® Pentium® M processor or Intel® Celeron® M processor 2. Supports 2 Serial-A T A devices with Software RAID 0 or 1 func- tions 3. Supports DDR 200/ 266/333 SDRAM up to 2GB 4. Optional onboard Adaptec AIC-7899 du al channel Ultra160 SCSI up to 160MB/sec.
PCA-6189 User’s Manual 4 • Floppy disk drive interface: Supports up to two floppy disk drives, 5¼" (360 KB and 1.2 MB) and/or 3½" (720 KB, 1.44 MB). BIOS enabled/d isabled 1.3.2 Memory • RAM: Up to 2 GB in two 184-pin DIMM so ckets. Supports DDR266/ 333 SDRAM 1.
5 L VDS connector , dual channel: 25 MHz to 1 12 MHz DVI connector: 2048 x 1536, 75 MHz 1.3.5 Ethernet LAN • Supports single 10/100Base-T networking or sing le/dual10/100/ 1000Base-T Ethernet netwo .
PCA-6189 User’s Manual 6 ers. Chapter 2 gives instructions for connecting external devices to your single board computer . T able 1.1: Jumpers Label Function J1 CMOS Clear J2 W atchdog timer output selection T able 1.
7 Notice: The 4-pin ATX 12V power connector "ATX1" must be connected to the power supply to provide adequate power to the CPU card. Otherw ise system might be unstable.
PCA-6189 User’s Manual 8 1.5 Board Layout: Jumper and Connector Location Figure 1.1: Jumper and Connector locations.
9 Figure 1.2: I/O Connectors Figure 1.3: SCSI daughter board 50 Pin for Ultra wide SCSI 68 Pin for Ultra 160 Adaptec AIC-7899 68 Pin for Ultra 160.
PCA-6189 User’s Manual 10 1.6 PCA-6189 Block Diagram Figure 1.4: Block Diagram.
11 1.7 Safety Precautions Notice: Before install your PCA-6189 into a chassis, make sure that all components on both sides of the CPU card do not touc h any metal parts, especially the chassis wall and add-on card at the adjacent slot. Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware.
PCA-6189 User’s Manual 12 1.8 Jumper Setti ngs This section provides instru ctions on how to configure your single board computer by setting the jumpers. It also includes the single board com- puter's default settings and your options for each jumper .
13 1.9 System Memory The PCA-6189 has two so ckets for 184-pin dual inline memory m odules (DIMMs). All these sockets use 2.5 V unbuffered double data rate synchronous DRAMs (DDR SDRAM).
PCA-6189 User’s Manual 14 1.9.1 CPU FSB and memory speed The PCA-6189 can accept DDR SDRAM memory chips without parity . Also note: The PCA-6189 accepts PC2100 (DD R266), PC2700 (DDR 333) and DDR SDRAM, depending on the CPU front side bus frequency (FSB).
15 1. T o open the socket, turn the socket screw clockwise as far as it will go. 2. Place the CPU in the empty socket an d then follow the instructions that came with the CPU.
PCA-6189 User’s Manual 16.
17 Chapter 2 CHAPTER 2 Connecting Peripherals.
PCA-6189 User’s Manual 18 Chapter 2 Connecting Peripherals 2.1 Introduction Y ou can access most of the connectors fr om the top of the board while it is installed i n the chassis. If you have a number of card s installed or have a packed chassis, you may need to pa rtially remove the card to make all the connections.
19 Chapter 2 Connect the first hard drive to the oth er end of the cable. Wire 1 on the cable should also co nnect to pin 1 on the hard drive connector, which is labeled on the drive circuit board. Check the documentation that came with the drive fo r more informati on.
PCA-6189 User’s Manual 20 2.4 Parallel Port (CN4) The parallel port is normally used to connect th e single board computer to a printer . The PCA-6189 includes an onboard parallel port, accessed through a 26-pin flat-cable connector, CN4. The card comes with an adapter cable which lets you use a tr aditional DB-25 connector .
21 Chapter 2 2.5 USB Port s CN6, CN31, and CN32 The PCA-6189 provides up to four ports for the USB (Univ ersal Serial Bus) interface, which gives complet e Plug & Play and hot swapping for up to 127 external devices.The US B interface complies with USB Speci- fication Rev .
PCA-6189 User’s Manual 22 2.6 VGA Connector CN7 The PCA-6189 includes a VGA interface that can drive conventional CR T displays. CN7 is a standard 15-pin D-SUB connector commonly used for VGA. Pin assi gnments for CR T connector CN7 are detailed in Appendix B.
23 Chapter 2 2.8 DVI connector VCN3 The VCN3 provides a DVI interface th at supports DVI display . This con- nector should be used with a 20-pin DV I cable (p/n: 1 700000821) Pin assignments fo r the VCN3 are detailed in Ap pendix B.
PCA-6189 User’s Manual 24 2.10 Serial Port s (COM 1 : CN9; COM2 : CN10 ) The PCA-6189 offers two serial ports, CN9 as COM1 and CN10 as COM2. These ports can connect to seri al devices, such as a mouse or a printer , or to a communi cations network. The IRQ and address ranges for both ports are fixed.
25 Chapter 2 2.12 External Keyboard Connector (CN12) In addition to the PS/2 mouse/keyb oard connector on the PCA-6189's rear plate, there is al so an extra onboard exte rnal keyboard connecto r . This gives system integrators greater flexibility in designing their sys- tems.
PCA-6189 User’s Manual 26 2.14 Front Panel Connector s (CN16, 17, 18, 19, 21&29) There are several extern al switches to monitor and control the PCA -6189 2.14.1 Power LED (CN16) CN16 is a 5-pin conn ector for the power on LED. Refer t o Appendix B for detailed information on the pin assignm ents.
27 Chapter 2 2.14.3 Reset (CN18) Many computer cases offer the convenie nce of a reset button. Connect the wire from the reset button. 2.14.4 HDD LED (CN19) Y ou can connect an LED to connector CN19 to indicate when the HDD is active.
PCA-6189 User’s Manual 28 2.15 A TX feature connector (CN20) Connect to the CN1 on the Advantech backplane to enable the A TX func- tion, 5V stand-by . 2.16 AC-97 Audio interface (CN43) The PCA-6189 provides AC-97 audio through PCA -AUDIO-00A1 module from Advantech.
29 Chapter 2 2.17 Serial A T A inte rface (SA0 and SA1) In addition to the two EIDE interfaces (up to f our devices), the PCA-6189 features high performance serial A T A interface (up to 150MB /s) which eases cabling to hard drives with thin and long cables.
PCA-6189 User’s Manual 30 2.19 Auxiliary 4-pin power connector (A TX1) T o ensure the sufficiency of power supply for Pentium M or Celeron M single board computer, one auxiliary 4 pin power connector is available on PCA-6189. This connector must be connected to the power supply , otherwise system might be unstable.
31 Chapter 3 CHAPTER 3 A ward BIOS Setup.
PCA-6189 User’s Manual 32 Chapter 3 A ward BIOS Setup 3.1 Introduction A ward’ s BIO S ROM has a built-in setup program that allows you to mod- ify the basi c system configuration. Th is type of inform ation is stored in battery-backed memory (CMOS RAM) so that it retains the setup info r- mation when the power is turned off.
33 Chapter 3 3.2 Entering Setup T urn on the computer and press <D el> to enter the BIOS setup. Figure 3.1: A ward BIOS Setup initial screen 3.3 St andard CMOS Setup Choose the S tandar d CMOS Featur es option from the initial setup screen menu to display the screen below .
PCA-6189 User’s Manual 34 3.4 Advanced BIOS Features The Advanced BIOS Featur es screen appears when you choose the Advanced BIOS Featur es item from the initial setup screen menu. Use this screen to configure the PCA- 6189 according to y our particular requirements.
35 Chapter 3 3.4.5 Quick Power On Self T est This setting allows the system to skip certain tests while boot ing. This will decrease the time need ed to boot the system. 3.4.6 First/Second/Third Boot Device The BIOS will load the OS with the devices in the sequence selected.
PCA-6189 User’s Manual 36 3.4.15 Security Option Choose an option for this setting to have the system prom pt for a pass- word every time the system boot s or only when you enter setup. System : The system will not boot and access to setup will be denied if the correct password is not entered at the prompt.
37 Chapter 3 3.5 Advanced Chip set Features By choosing the Advanced Ch ipset Features option from the Initial Setup Screen menu, the screen below will be displayed. This sample screen contains the manufacturer ’ s default values for the PCA-6189, as shown in Figure 3-4: Figure 3.
PCA-6189 User’s Manual 38 3.5.4 DRAM RAS# to CAS# Delay In order to improve performance, certa in space in memory is reserved for ISA cards. This memory must be map ped into the memo ry space below 16 MB. The choices are: 3 and 2. 3.5.5 DRAM RAS# Precharge This controls the idle clocks after issuing a precharge command to DRAM.
39 Chapter 3 3.5.12 AGP Aperture Size (MB) Use this setting to select the size of the Accelerated Gr aphics Port (AGP) aperture. The aperture is a portion of the PCI memory address range ded- icated to graphics memory address space. Host cycles that hit the aperture range are forwarded to the A GP without any translation.
PCA-6189 User’s Manual 40 3.6 Integrated Peripherals Figure 3.5: Integrated peripherals 3.7 On-chip IDE Device Figure 3.6: On-Chip IDE Device 3.7.1 IDE DMA transfer access This setting controls the DMA function of hard disk driv e. The choices are Enabled or Disabled .
41 Chapter 3 3.7.2 On-Chip IDE Device IDE Primary (Secondary) Master/Slave PIO/UDMA Mode (Auto) Each channel (Primary and Secondary) has both a master and a slave, making four IDE devices possible. Because each IDE device may have a dif ferent Mode timing (0, 1, 2, 3, 4), it is necessary for these to be independent.
PCA-6189 User’s Manual 42 3.8.1 USB Controller Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have USB peripherals. The choices are Enabled or Disabled . 3.8.2 USB 2.0 Controller Use this option to disable/en able the USB 2.
43 Chapter 3 3.9.1 On-board FDC Controller When enabled, this field allo ws you to connect your floppy d isk drives to the onboard floppy disk drive connector instead of a separate controller card. If you want to use a dif ferent controller card to connect the floppy disk drives, set this field to Disabled .
PCA-6189 User’s Manual 44 faster than the maximum data transfer rate. ECP+EPP allo ws normal speed operation in a two-way mode. 3.9.1 1 EPP Mode Select This field allows you to select EPP po rt type 1.7 or 1.9. The choices are: EPP1.9 or EPP1.7. 3.9.
45 Chapter 3 Max Saving, the values for HDD Power Down and Suspend Mode (the following settings) are filled in autom atically . If you select User Defined, you must also enter values for HDD Power Down and Suspend Mode. 3.10.3 V ideo Off Method Use this setting to select a metho d to turn off the video.
PCA-6189 User’s Manual 46 3.10.9 Power On by LAN Choose Enabled to resume system functi on by LAN, or choose Disabled to resume system functio n by PCI card. 3.10.10 Power On by Modem This item allows you to wake up th e system via a COM port from the remote host.
47 Chapter 3 3.1 1.1 PNP OS Inst alled Set this option to Ye s if PNP OS is installed on your system. The default value for this setting is No . 3.1 1.
PCA-6189 User’s Manual 48 3.12.2 Current System T emp This shows you the curren t temperature of system. 3.12.3 Current CPU T emperature This shows you the current CPU temperature. 3.12.4 Current CPUF AN Speed This shows you the current CPU fan operating speed.
49 Chapter 3 3.14 Passwords and Settings 3.14.1 Load Setup Default s Choose the Load Setup De faults selection from the initial setup screen. At the prompt, enter Y to return system setup options to default values. 3.14.2 Set Supervisor Password Choose the Set Supervisor Pa sswor d selection from the initial setup screen.
PCA-6189 User’s Manual 50.
51 Chapter 4 CHAPTER 4 Chip set Sof tware Inst allation Utility.
PCA-6189 User’s Manual 52 Chapter 4 Chip set Sof tware Inst all Utility 4.1 Before you begin T o facilitate the installation of th e enhanced display device drivers and utility software, you shoul d read the instructions in this chapter carefully before you attempt installatio n.
53 Chapter 4 • Identification of Intel chipset componen ts in the Device Manager . • Integrates superior video features. These include filtered sealing of 720 pixel DVD cont ent, and MPEG-2 motion co mpensation for soft- ware DVD 4.3 Windows XP Driver Setup 1.
PCA-6189 User’s Manual 54 2. Click "Next" when you see the following message. 3. Click "Y es" when you see the following message.
55 Chapter 4 4. Click "Next" when you see the following message. 5. When the following message appear s, click "Finish" to complete the installation an d restart W indows.
PCA-6189 User’s Manual 56.
57 Chapter 5 CHAPTER 5 VGA Setup.
PCA-6189 User’s Manual 58 Chapter 5 VGA Setup 5.1 Introduction The PCA-6189 has VGA onbo ard, you need to install the VGA driv er to enable the function. The Intel 855GME Chipset provides a highly integrated graphics acceler- ator delivering hig h performance 2D, 3D, and video capabilities.
59 Chapter 5 5.3 Windows XP Driver Setup 1. Insert the driver CD into your system's CD-ROM drive. In a few seconds, the software installation ma in menu appears, as shown in the following figure.
PCA-6189 User’s Manual 60 2. Y ou will see a welcome window . Please chick on "Next" to con- tinue the installation..
61 Chapter 5 3. Click "Y es" when you see the following message. 4. Click on "Y es" to continue the installati on.
PCA-6189 User’s Manual 62 5. Click "Finish" to comp lete the installation and restart the compu ter now or later ..
63 Chapter 6 CHAPTER 6 LAN Configuration.
PCA-6189 User’s Manual 64 Chapter 6 LAN Configuration 6.1 Introduction The PCA-6189 features the 32-bit 10/100/1000 Mbps Ethernet network interface. This interface supports bus mastering archit ecture and auto- negotiation features.
65 Chapter 6 6.3 Inst allation The PCA-6189's onboard Ethernet inte rface supports all majo r network operating systems. However , the instal lation procedure varies with differ- ent operating systems. In the following sections, refer to the one that pro- vides driver setup procedure for the operating system you are using.
PCA-6189 User’s Manual 66 2. Select "I accept the terms in th e license agreement" and click "Next" to continue. 3. Click "Next" to continue.
67 Chapter 6 4. Click "Install Software" to start the instal lation procedure. 5. The driver will be installed au tomaticall y and the LAN function will be enabled after the installation.
PCA-6189 User’s Manual 68.
69 Chapter 7 CHAPTER 7 SCSI Setup & Configuration.
PCA-6189 User’s Manual 70 Chapter 7 SCSI Setup & Configuration 7.1 Introduction The PCA-6189 is equipped with an Adaptec AIC-7 899 single-chip PCI- to-SCSI host ad apter which provide s a dual channel Ultra 160 multi- tasking interface between your comp uter .
71 Chapter 7 7.2 Underst anding SCSI SCSI (pronounced .scuzzy .) stands for Small Co mputer Systems Inter- face. SCSI is an industry standard computer interface for connecting SCSI devices to a common SCSI bus. A SCSI bus is an electrical pathway that consists of a SCSI interface installed in a computer and one or more SCSI devices.
PCA-6189 User’s Manual 72 • If you are booting your computer from a SC SI hard disk drive con- nected to the SCSI bus, the Boot SC SI ID setting in the SCSISelect utility must correspond to the SCSI ID of the device from which you are booting. By default, the Boot SCSI ID is set to 0.
73 Chapter 7 7.5 Configuring the SCSI interface with SCSISelect SCSISelect, included with the CPU card, enables you to change SCSI set- tings without open ing the computer . SCSISelect also enables you to low- level format or verify the disk media of your SCSI hard disk drives.
PCA-6189 User’s Manual 74 SCSI Devi ce Configur ation: Sync T ransfer Rate (MBytes/sec) 160, 80.0, 53.4, 40.0, 160 32.0, 26.8, 20.0, 16.0, 13.4, 10. 0 ASYN Initiate Wide Negotiation Y es, No Y es (e.
75 Chapter 7 7.6 St arting SCSISelect Follow these steps to start SCSISelect: 1. T urn on or restart your system. D uring the startup process, pay careful attention to the messages that appear on your screen.
PCA-6189 User’s Manual 76 Using SCSISelect Settings T o select an option, use the arrow keys to move the cursor to the optio n, then press ENTER. In some cases, se lecting an option displays another menu. Y ou can return to the previous men u at any time by pressing ESC.
77 Chapter 7 • Initiate W ide Negot iation -(Default: Y es) When set to Y es, the SCSI card attempts 16-bit data transfer (wide negotiation.) When set to No, the SCSI card uses 8-bit data transf er unless the SCSI device requests wide negotiation.
PCA-6189 User’s Manual 78 • Display <Ctrl> <A> Messages during BIOS Initialization -(Default: Enabled) When set to Enabled, the SCSI card BIOS displays the Press <Ctrl> <A> for SCSI Select (TM) Utility! message on y our screen dur- ing system bootup.
79 Chapter 7 • Support Removable Disks Und er BIOS as Fixed Dis ks. (Default: Disabled) Determines which remo vable-media drives are support ed by the SCSI card BIOS. Choices are as follows: • Disabled. No removable-media drives are treated as hard disk drives.
PCA-6189 User’s Manual 80 7.8 Inst allation under Windows 2000 If you are only using SCSI hard drives withou t any IDE HDD drive installed. Please follow these steps: 1. Insert W indows 2000 CD Disk. 2. Press F6 immediately when it di splays: “Set up is inspecting your computer ’ s h ardware configuration.
81 Chapter 7 2. In the “Sy stem properties”, choos e “PCI SCSI Bus Controller .” Then click on “Properties.” 3. Click on "Update Driver".
PCA-6189 User’s Manual 82 4. Click on “Next” 5. Recommend to search for a better driver.
83 Chapter 7 6. If the SCSI driver is supplied in floppy disk, click on “Floppy disk drives.” Then, click on “Next.” If the SCSI driver is supplied in CD-ROM disk, click on “Specify a location:" then enter "E:Drv_SCSIAIC7899WindowsW in9X" 7.
PCA-6189 User’s Manual 84 8. The installation is completed. Cli ck on "Finish." 9. Click on "Y es" to restart the system..
85 Chapter 8 CHAPTER 8 USB 2.0 Configuration.
PCA-6189 User’s Manual 86 Chapter 8 USB 2.0 Configuration 8.1 Introduction The PCA-6189 is designed with Intel 630 0ESB which supports both USB 1.1 and USB 2.0 high-speed tran smission. It still remains the comp atibil- ity with today's USB device.
87 Chapter 9 CHAPTER 9 Onboard Security Setup.
PCA-6189 User’s Manual 88 Chapter 9 Onboard Security Setup 9.1 Introduction The PCA-6189's hard ware monitor is desig ned with W inbond W83627HF . Onboard secur ity (OBS) functions moni tor key hardwar e. They help you mainta in your sy stem's stability and durability .
89 Chapter 9 9.2 Windows XP Driver Setup 1. Insert the driver CD into your system's CD-ROM drive. In a few seconds, the software installation main menu appears, as shown in the following figure. Click on the "Ins tall" button under the "OBS DRIVERS" heading.
PCA-6189 User’s Manual 90 3. Click "Next" when you see the following message. 4. Click "Next" when you see the following message.
91 Chapter 9 6. Click "Finish" when you see the followi ng message. 9.3 Using the OBS Hardwa re Doctor Utility After completing the setup, all th e OBS functions are permanently enabled. When a monitored reading exceeds safe limits, a warning mes- sage will be displayed and an error b eep tone will activate to attract your attention.
PCA-6189 User’s Manual 92 2. It is recommended that you load the default values fo r all the OBS settings. However , if desired, you can establish new conditions for voltage, fan speed, and temperature.
93 Chapter 10 CHAPTER 10 SA T A RAID Setup.
PCA-6189 User Manual 94 Chapter 10 SA T A RAID Setup 10.1 Introduction T o support demanding disk I/O, Intel 6300 ESB chipset integrates two Serial A T A controllers with software RAID 0 and 1 capabilit y . RAID 0 stripping increases the storage perfor mance and is designed to speed up data transfer rates for disk-i ntensive application s.
95 Chapter 10 10.3 Array Configuration Utility Select the “Array Configuration Uti lity” in the “Initi al Setup Screen” menu, and the “SA T A RAID Setup Main Menu screen” screen will dis- play . This menu allows users to co nfigure RAID function such as man- age/create array , add/delete ho tspare and initialize drives.
PCA-6189 User Manual 96 10.3.2 Creating Arrays Before creating arrays, please make sure that the disks for the array already connected and in stalled in the system. 1. Select “Create Array” from the setup main menu 2. Select the disks for the new array then pres s “Insert”.
97 Chapter 10 4. Press “Enter” 5. Read the warning message and type “Y” to continue 10.3.6 Rebuilding Arrays Y ou can rebuild the array to have optimal status by rep lacing a failed disk of a RAID 1 or RAID 10 arra y with a new disk.
PCA-6189 User Manual 98 3. When the array is build, insert the driver CD and restart the system 4. Windows searches the disk for a suitable driver 5. When the Adaptec Embedded Se rial A T A HostRAID driver is found, press “Enter”. Follow the instruct ions to complete your installation.
99 Appendix A Appendix A Programming the W atchdog T imer.
PCA-6189 User’s Manual 100 Appendix A Programming the watchdog A.1 Programming the W atchdog Timer The PCA-6189's watchd og timer can be used to monitor system so ftware operation and take correc tive action if the software fails to functio n after the programmed period.
101 Appendix A Unlock W83627H Select register of watchdog timer Enable the function of the watchdog timer Use the function of the watchdog time r Lock W83627HF.
PCA-6189 User’s Manual 102 W atchdog Timer Registers Address of regis ter (2E) Attribute Read/Write V alue (2F) and description 87 (hex) ----- Write this addres s to I/O address port 2E (hex) twice to unlock theW83627HF 07 (hex) write Write 08 (hex) to select reg- ister of watchdog timer .
103 Appendix A T able A.1: W atchdog ti mer registers A.1.4 Example Program 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- ----------- ---------- --------- ----------.
PCA-6189 User’s Manual 104 ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Set second as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;---.
105 Appendix A ;-------- --------- ----------- ---------- --------- ---------- -- Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- --.
PCA-6189 User’s Manual 106 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;-------.
107 Appendix A Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;-------- --------- --.
PCA-6189 User’s Manual 108 Out dx,al ;-------- --------- ----------- ---------- --------- ---------- -- Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;-------.
109 Appendix B Appendix B I/O Pin Assignment s.
PCA-6189 User’s Manual 110 Appendix B Pin Assignment s B.1 IDE Hard Drive Connector (CN1, CN2) T able B.1: IDE hard drive connector (CN1, CN2) Pin Signal Pin Signal 1 IDE RESET* 2 GND 3D A T A 7 4 D.
111 Appendix B B.2 Floppy Drive Connector (CN3) T able B.2: Floppy dr ive connector (CN3) Pin Signal Pin Signal 1 GND 2 FDHDIN* 3G N D 4 N / C 5 N/C 6 FDEDIN* 7 GND 8 INDEX* 9 GND 10 MOTOR 0* 1 1 GND .
PCA-6189 User’s Manual 112 B.3 Parallel Port Connector (CN4) T able B.3: Parallel port connector (CN4) Pin Signal Pin Signal 1 STROBE* 14 AUTOFD* 2D 0 1 5E R R 3D 1 1 6I N I T * 4D 2 1 7 S L C T I N.
113 Appendix B B.4 USB Connector (CN6) B.5 VGA Connector (CN7) T able B.4: USB1/USB2 connector (CN6) Pin USB1 Signal Pin USB2 Signal 1+ 5 V 6 + 5 V 2 UV- 7 U V- 3 UV+ 8 UV+ 4G N D 9 G N D 5 Chassis GND 10 N/CA T able B.
PCA-6189 User’s Manual 114 B.6 VCN2 L VD connector (Insert diagram) T able B.6: VCN2 L VDS connector Pin Signa l Pin Signal 1 VDDSAFE5 21 G4 2 VDDSAFE5 22 G5 3G N D 2 3 G 6 4G N D 2 4 G 7 5 VDDSAFE3.
115 Appendix B B.7 VCN3 DVI connector (insert diagram) B.8 COM1/COM2 RS-232 Se rial Port (CN9, CN10) (insert diagram) T able B.7: VCN3 DVI connector Pin Signal Pin Signal 1 #TMDS1_0 1 1 GND 2 AGP_5V_T.
PCA-6189 User’s Manual 116 B.9 PS/2 Keyboard/M ouse Connector (CN1 1) (INSER T DIAGRAM) B.10 External Key board Connector (CN12) (Insert diagram) B.1 1 Power LED (CN16) (insert diagram) T able B.9: PS/2 keyboard/mouse connecto r (CN1 1) Pin Signal 1 KB DA T A 2M S D A T A 3G N D 4V C C 5 KB CLOCK 6M S C L O C K T able B.
117 Appendix B B.12 Power LED (CN16) (insert diagram) B.13 External Speak er Connector (CN17) (insert diagram) T able B.12: Power LED (CN16) Pin Function 1 LED po wer (+5 V) 2N C 3G N D 4N C 5G N D T able B.
PCA-6189 User’s Manual 118 B.14 Reset C onnector (CN18) B.15 A TX Feature Connector (CN20) T able B.14: Reset connector (CN18) Pin Signal 1 RESET 2G N D T able B.
119 Appendix B B.16 A TX Feature Connector (CN20) B.17 A TX Sof t Power Switch (CN21) T able B.16: A TX Feature Connector (CN20) Pin Signal 1 PS-ON 2V C C 3V C C S B T able B.
PCA-6189 User’s Manual 120 B.18 H/W Monitor Alarm (CN22) B.19 SM Bus Connector (CN29) T able B.18: H/W Monitor alarm (CN22) Pin Signal 1 Enable OBS alarm 2 Disable OBS alarm T able B.
121 Appendix B B.20 Audio Interface (CN43) (insert diagram) B.21 LCD Inverter pow er connectore (VP1) (insert diagram) T able B.20: Audio Interface(CN 43) 1 VCC 2 GND 3 Sync 4 BITCLK 5 SDOUT 6 SDIN0 7 SDIN1 8 AC-RST 9 +12V 10 GND 1 1 GND 12 N/C T able B.
PCA-6189 User’s Manual 122 B.22 System I/O Port s T able B.22: System I/O ports Addr . range (H ex) Device 000-01F DMA controller 020-021 Interrupt controller 1, master 022-023 Chipset address 040-0.
123 Appendix B B.23 DMA Channel Assignment s B.24 Interrupt Assignment s T able B.23: DMA channel assignments Channel Functio n 0A v a i l a b l e 1A v a i l a b l e 2 F loppy disk (8-bit transfer) 3A v a i l a b l e 4 Ca scade for DMA controller 1 5A v a i l a b l e 6A v a i l a b l e 7A v a i l a b l e T able B.
PCA-6189 User’s Manual 124 B.25 1st MB Memory Map B.26 PCI Bus Map T able B.25: 1st MB memory map Addr . range (Hex) Device E0000h - FFFFFh BIOS CC000h - DFFFFh Unused C0000h - CBFFFh VGA BIOS A0000h - BFFFFh Video Memory 00000h - 9FFF Fh Base memory T able B.
An important point after buying a device Samsung PCA-6189 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samsung PCA-6189 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samsung PCA-6189 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samsung PCA-6189 you will learn all the available features of the product, as well as information on its operation. The information that you get Samsung PCA-6189 will certainly help you make a decision on the purchase.
If you already are a holder of Samsung PCA-6189, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samsung PCA-6189.
However, one of the most important roles played by the user manual is to help in solving problems with Samsung PCA-6189. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samsung PCA-6189 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
