Instruction/ maintenance manual of the product RF-502 Auto Page
Go to page of 18
RF - 502 OPERATION INSTRUCTIONS.
Congratulations on your purchase of the RF - 502 vehicle security system. AutoPage, Inc. is one of the companies with the longest history and experience in vehicle security in the United States and a wh olly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
RF - 502 1 RF - 502 OPERATION I NSTRUCTIONS A. REMOTE CONTROL TRANSMITTER OPERATION The new remote control transmitter (XT - 54) included with the RF - 502 offers the code rolling feature which will prevent illegal use of a code - grabber with an attempt to record the code of your transmitter.
RF - 502 2 particular operation. The sequence must be repeated each time if it is desired to cancel the arm/disarm chirp sound. 3. PANIC FUNCTION The RF - 502 remote control may be used as a remote panic switch to trigger the siren in cases of emergency.
RF - 502 3 To replace the battery, carefully remove the case screw located at the end of the remote where the key ring attaches to the case. Use a small blade Phillips screwdriver.
RF - 502 4 D. VALET/OVERRIDE SWITCH NOTE : Both VALET and OVERRIDE functions are performed from the same switch. 1. OVERRIDE FUNCTION The OVERRIDE FUNCTION may be used if the RF - 502 remote is lost or inoperative. To operate the OVERRIDE FUNCTION, enter the vehicle (siren will sound); switch the vehicle ignition to ON.
RF - 502 5 E. PASSIVE/MANUAL ARMING OPERATION (Optional at installation) Passive/Manual operations can be selectable if an optional toggle switch is installed. Consult your installing dealer. 1. PASSIVE ARMING If you choose the PASSIVE (aut omatic) mode, the system must be operated as below.
RF - 502 6 Approach the vehicle and press the ON/OFF remote transmitter button. The siren will chirp 2 times and the lights will flash to indicate the RF - 502 is disarmed.
RF - 502 7 1. Open any door or other protected opening. The siren will sound instantly, and the lights will flash. 2. If the pre - warning feature is activated, the RF - 502’s SIS - 5 impact sensor will respond to a light shock with a chirp sound, and trigger the alarm when a heavier shock is detected.
RF - 502 8 4. Turn the igniti on switch "ON/OFF", "ON/OFF". The siren will chirp one (1) time. You are now in the programming mode. 5. Press the ON/OFF button on one of the remote transmitters until the alarm siren responds with a confirming chirp.
RF - 502 9 Enter the programming mode on vehicle #1 and push the ON/OFF button on the tran smitter for Vehicle #1. The alarm siren will respond with a confirming chirp. Within five (5) seconds , push the AUX button on the transmitter for Vehicle #2. The alarm siren will respond with a confirming chirp.
RF - 502 10 AUTOPAGE ALARM ACCESSORIES AP - 4000DX Paging System Vehicle secu rity paging was originated by AutoPage over 18 years ago. The AP4000DX is our latest version providing a full four watts of output power to signal a handsome belt - clip paging receiver indicating your RF - 502 has been triggered, even if you cannot hear the siren.
RF - 502 11 sensors, the SIS - 10 has a LED and potentiometer for easy sensitivity adjustment. MSEN - KIT The MSEN - KIT includes two pre - wired Micro Resonance Sensors and a special triggering amplifier.
12 LIMITED LIFETIME WARRANTY PROVISIONS (U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
RF - 502 13 7 AutoPage shall not be liable, under the foregoi ng WARRANTIES or otherwise, for: Any personal injury of any kind to the purchaser, its employees or agents or anyone else whomsoever resul.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
13 DATE SERVICE COMPLETED.
1815 W. 205th St. #101 Torrance, CA 90501 310 - 618 - 2002.
An important point after buying a device Auto Page RF-502 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Auto Page RF-502 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Auto Page RF-502 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Auto Page RF-502 you will learn all the available features of the product, as well as information on its operation. The information that you get Auto Page RF-502 will certainly help you make a decision on the purchase.
If you already are a holder of Auto Page RF-502, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Auto Page RF-502.
However, one of the most important roles played by the user manual is to help in solving problems with Auto Page RF-502. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Auto Page RF-502 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
