Instruction/ maintenance manual of the product RF-302 Auto Page
Go to page of 20
RF - 302 OPERATION INSTRUCTIONS.
Congratulations on your purchase of the RF - 302 vehicle security system. AutoPage, Inc. is one of the companies with the longest history and experience in vehicle security in the United States and a wh olly owned subsidiary of Iwata Electric Co., of Tokyo, Japan.
RF - 302 1 RF - 302 OPERATION I NSTRUCTIONS A. REMOTE CONTROL TRANSMITTER OPERATION 1. ARM/DISARM TO ARM THE RF - 302 Press the ON/OFF button once to arm. The siren will chirp one (1) time, the lights will flash, and all doors will lock. (*) TO DISARM THE RF - 302 Press the ON/OFF button once to disarm.
RF - 302 2 3. PANIC FUNCTION The RF - 302 remote control may be used as a remote panic switch to trigger the siren in cases of emergency. To activate the PANIC FUNCTION press and hold the ON/OFF button on the remote transmitter for a minimum of 3 seconds.
RF - 302 3 To replace the battery, carefully remove the case screw located at the end of the remote where the key ring attaches to the case. Use a small blade Phillips screwdriver.
RF - 302 4 NOTE : Both VALET and OVERRIDE functions are performed from the same switch. 1. OVERRIDE FUNCTION The OVERRIDE FUNCTION may be used if the RF - 302 remote is lost or inoperative. To operate the OVERRIDE FUNCTION, enter the vehicle (siren will sound); switch the vehicle ignition to ON.
RF - 302 5 1. PASSIVE ARMING If you choose the PASSIVE (automatic) mode, the system must be operated as below. 1. Switch OFF vehicle ignition, exit vehicle, and be sure all protected openings are closed. 2. The LED STATUS INDICATOR will begin fast flashing and the passive arming timer will begin counting down.
RF - 302 6 Approach the vehicle and press the ON/OFF remote transmitter button. The siren will chirp 2 times and the lights will flash to indicate the RF - 302 is disarmed.
RF - 302 7 1. Open any door or other protected opening. The siren will sound instantly, and the lights will flash. 2. If optional sensors have been installed, arm the RF - 302 and test according to the directions of the particular sensor installed.
RF - 302 8 4. Turn the ignition switch "ON/OFF", "ON/OFF". The siren w ill chirp one (1) time. You are now in the programming mode. 5. Press the ON/OFF button on one of the remote transmitters until the alarm siren responds with a confirming chirp.
RF - 302 9 Enter the programming mode on vehicle #1 and push the ON/OFF button on the transmitter for Ve hicle #1. The alarm siren will respond with a confirming chirp. Within five (5) seconds , push the AUX. button on the transmitter for Vehicle #2. The alarm siren will respond with a confirming chirp.
RF - 302 10 AUX. BUTTON ON/OFF BUTTON BOTH BUTTONS TRANSMITTER #3 AUX. BUTTON BOTH BUTTONS ON/OFF BUTTON BOTH BUTTONS AUX. BUTTON ON/OFF BUTTON.
RF - 302 11 AUTOPAGE ALARM ACCESSORIES AP - 4000DX Paging System Vehicle s ecurity paging was originated by AutoPage over 18 years ago. The AP4000DX is our latest version providing a full four watts of output power to signal a handsome belt - clip paging receiver indicating your RF - 302 has been triggered, even if you cannot hear the siren.
RF - 302 12 sensors, the SIS - 10 has a LED and potentiometer for easy sensitivity adjustment. MSEN - KIT The MSEN - KIT includes two pre - wired Micro Resonance Sensors and a special triggering amplifier.
12 LIMITED LIFETIME WARRANTY PROVISIONS (U.S. and Continental U.S. Only) 1. AutoPage, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
RF - 302 13 LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 7 AutoPage shall not be liable, under the foregoing WARRANTIES or otherwise, for: Any p ersonal injury of an.
.
This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
13 DATE SERVICE COMPLETED.
1815 W. 205th St. #101 Torrance, CA 90501 310 - 618 - 2002.
An important point after buying a device Auto Page RF-302 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Auto Page RF-302 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Auto Page RF-302 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Auto Page RF-302 you will learn all the available features of the product, as well as information on its operation. The information that you get Auto Page RF-302 will certainly help you make a decision on the purchase.
If you already are a holder of Auto Page RF-302, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Auto Page RF-302.
However, one of the most important roles played by the user manual is to help in solving problems with Auto Page RF-302. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Auto Page RF-302 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
