Instruction/ maintenance manual of the product PRO 9171FT Audiovox
Go to page of 12
3 Channel Remote Car Starter Installation Instructions For installation in vehicles with 12 volt negative ground circuits, gasoline engines, with automatic transmission only! Model PRO 9171FT Installa.
The PRO-9171FT is for Automatic Transmission vehicles only! Although it is a sophisticated system, with multiple built-in safety features, it must not be installed into vehicles with manual transmissions. Doing this can cause serious personal injury and property damage.
LIGHT GREEN Wire : Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show +12 Volts when the ignition key is turned to the “ RUN or ON “ position, and in some cases, the “ START or CRANK “ position.
4 This wire provides a 500 mA + 12 Volt transistorized output when the ignition key is turned to the “ON” position, and 0 Volts when the ignition key is “OFF” and when the vehicle is running under the control of the remote starter. This wire should be connected to the ignition input of the alarm system.
5 DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the tach rate while the engine is running under power supplied by the Remote Starter. This wire will be routed through the fire wall into the engine compartment. It is necessary to use an existing grommet when passing wires through the fire wall to prevent short circuiting.
To program these selectable features: 1. Start with the programming switch in the OFF position. 2. Turn the ignition key to the ON position. 3. Flip the program switch ON - OFF - ON - OFF - ON - then OFF. 4. Immediately turn the ignition key OFF, then back to ON.
NEUTRAL ST ART SAFETY TEST : The intent of the neutral start switch is to prevent the vehicle from starting while the gear selector is in any position other than Park, or Neutral. When installing a Remote S tart Device, it is imperative that the Y ellow Starter wire be connected to the ignition switch side of the Neutral Start Switch.
KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral S t art Switch from starting in gear .
T o connect to the key in sensor as shown in method 1: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .
10 NOTE: A second 4002 series diode may be required to maintain t he integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit.
12 PIN CONNECTOR WIRING THE 12 PIN INPUT / OUTPUT HARNESS CONTROL SWITCH TO ALARM'S IGNITION INPUT- (YELLOW WIRE OF AUDIOVOX ALARMS) LIGHT BLUE WHITE WHITE POSITIVE INHIBIT 1 NEGATIVE INHIBIT 2 T.
© 1998 Audiovox Corporation, Hauppauge, NY 11788 128-5404.
An important point after buying a device Audiovox PRO 9171FT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox PRO 9171FT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox PRO 9171FT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox PRO 9171FT you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox PRO 9171FT will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox PRO 9171FT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox PRO 9171FT.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox PRO 9171FT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox PRO 9171FT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
