Instruction/ maintenance manual of the product MDR1064 Samson
Go to page of 24
MDR Series Mixers TEN CHANNEL MIXER.
Safety Instructions/Consignes de sécurité/Sicherheitsvor kehrungen/Instr ucciones de seguridad ACHTUNG: Um die Gefahr eines Brandes oder Stromschlags zu verringern, soll- ten Sie dieses Gerät weder Regen noch Feuchtigkeit aussetzen.Um die Gefahr eines Stromschlags zu verringern, sollten Sie weder Deckel noch Rückwand des Geräts entfernen.
T able of Contents Introduction 2 MDR1064 Features 3 Front and Rear Panel Layout 4 Front and Rear Panel Controls 5 Controls and Functions Mono/Stereo Input Channel Section 6–7 Master Section 8–9 M.
2 Congratulations on your purchase of the Samson MDR1064 mixer! The MDR1064 is a ten-channel mixer, with six low noise microphone pre-amps. The six Mic/line inputs and two stereo inputs each feature a 3-band equalizer plus two Aux sends.
3 MDR1064 F eatures The Samson MDR1064, ten-channel mixer is a comprehensive, all-in-one solution for live sound, recording, fixed installation and post production applications. Here are some of its main features: • Eight Channels – Six Mic/Line plus two Stereo inputs with mic pre’s.
4 F ront and Rear P anel La yout.
5 F ront and Rear P anel Controls FRONT PANEL 1 MIC IN – Input connector for Low-Noise Microphone pre- amp. 2 LINE IN –Input connector for Line level inputs. 3 INSERT – 1/-4-inch TRS (TIP/RING/SLEEVE) connector providing send and recieve channel patch point for out- board effects.
6 Controls and Functions MONO/STEREO INPUT CHANNEL SECTION The following section details each part of the MDR1064’s MONO INPUT CHANNELS including the GAIN con- trol, LOW CUT switch, 3-BAND EQ, AUX sends, PEAK LED, PAN and LEVEL controls.
BALANCE (Stereo Inputs Only) The MDR1064’s BALANCE control is used to place or position the stereo signal into the main Left and Right MIX bus. You can move a stereo signal’s image to the left or right by setting the BALANCE control to the left or to the right.
8 MAIN LEVEL The master MAIN control is the overall volume control for the left and right mix bus. These line level signals are output from the MAIN MIX jacks. PHONES / CR The PHONES / CR control is used to set the level sent to the control room outputs, and also to the headphone jack.
AUX RET 2 The AUX RETURN 2 adjusts the level of the signal present at the AUX 2 RET jacks. This signal is summed, or mixed in to the main L/R MIX bus. TO AUX 1 This routes the signal that is present on the AUX 2 RETURN jacks to AUX 1 so that the effects can be heard in the monitor mix.
CHANNEL 1 – 6 MIC and LINE INPUTS The MDR1064’s channel 1 through 6 mono inputs each have a 1/4-inch connector for line level signals and XLR connectors for the MIC signals. Channels 7/8 and 9/10 stereo inputs each have 1/4-inch connectors for line level inputs.
MAIN MIX LEFT/RIGHT XLR OUTPUTS In a live sound application, the LEFT/ RIGHT MIX outputs are connected to a power amplifier or powered speak- ers. In a recording application, the LEFT/ RIGHT MIX outputs are used to connect to the inputs of a stereo device such as computer sound card, DAT, or cassette recorder.
Operating the MDR1064 12 BASIC OPERATION The following section explains the basic operation of the MDR1064. CONNECTING MICROPHONES AND INSTRUMENTS 1. Before connecting mics or instruments, make sure that the power of all your systems components including the MDR1064 is turned off.
Operating the MDR1064 13 SENDING AN INDEPENDENT MIX TO THE MONITOR SPEAKERS The MDR1064’s AUX1 auxiliary send can be used to feed a separate set of amplifiers and loudspeakers for stage monitors.
14 Operating the MDR1064 USING AN EXTERNAL EFFECT If you prefer to use an external device for effects process- ing, you can easily connect the unit using the MDR1064 AUX 2 bus. Follow the simple steps below to interface your processor: 1. Connect the AUX 2 OUTPUT to the input of the exter- nal effect processor.
15 MDR1064 Sy stem Set-Ups This system shows the MDR1064 connected to a pair of powered speakers like the SAMSON Expedition EX20. The A UX SEND 1 output is connect- ed to an external power amp, which is driving 2 monitor speakers .
16 MDR1064 Sy stem Set-Ups This system shows the MDR1064 in a recording set up with the LEFT and RIGHT C ON- TROL ROOM output hooked up to powered studio monitors and the A UX 1 feed headphone mix sent to a Samson S phone headphone amp.
MDR1064 Wiring Guide Unbalanced 1/4” Connector XLR Balanced Wiring Guide CONNECTING THE MDR1064 The are several ways to interface the MDR1064 to support a variety of applications. The MDR1064 features bal- anced inputs and outputs, so connecting balanced and unbalanced signals is possible.
MDR1064 Specifications 18 Mono input channels Microphone input electronically balanced, discrete input con- figuration Frequency response 10Hz to 45kHz Distortion (THD & N) 0.
MDR1064 Block Diagram 19.
Notes 20.
.
Samson T echnologies Corp. 575 Underhill Blvd. P .O. Box 9031 Syosset, NY 1 1791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www .samsontech.
An important point after buying a device Samson MDR1064 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samson MDR1064 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samson MDR1064 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samson MDR1064 you will learn all the available features of the product, as well as information on its operation. The information that you get Samson MDR1064 will certainly help you make a decision on the purchase.
If you already are a holder of Samson MDR1064, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samson MDR1064.
However, one of the most important roles played by the user manual is to help in solving problems with Samson MDR1064. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samson MDR1064 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
