Instruction/ maintenance manual of the product 210C Samson
Go to page of 24
Hartke Hartke 1 1 2 C 1 1 5 C 2 1 0 C.
Important Safety Instruc tions 1. Please read all instructions before operating the unit . 2. Keep these instructions for future refer ence. 3. Please heed all safety warnings. 4. Follo w manufacturers instructions. 5. Do not use this unit near water or moisture.
Copyright 2007, Samson T echnologies Corp . Printed December , 2007 v1.0 Hartke 45 Gilpin Avenue Hauppauge, New Y ork 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) F ax: 631-784-2201 www.hartke.com T able of C ontents I n t r o d u c t i o n .....
2 Introduction Thank you f or purchasing the Hydrive Bass C ombo Amplifier from Hartke! W e k now you don ’t like r eading owners manuals, but y ou’ ve just purchased one of the finest bass amplifiers around, and w e want to tell y ou about it.
3 and at the same time lightweight. The vinyl cov ering, steel grill and corners pr ovide added protection while moving the amplifier from gig t o gig.
4 4 Har tke 112C,115C and 210C C ombo Bass Amplifier F eatures The Hartke Hydrive Combos offer all the newest c oncepts in state- of-the-ar t hybrid drive bass amplification in an extremely compact size and affor dable price.
5 • Specially designed cabinet which can be used either flat on the floor or on its “kick back ” position for increased high end clarity . • A rear panel, line-level direct output, with PRE/POST switch on standard XLR connector is provided f or interfacing with P A systems or recor ding mixing consoles.
6 Guided T our - F ron t P anel 1. INPUT (1/4-inch Jack) - Connect your bass guitar to this standar d 1/4" unbalanced jack. T his Hydrive Combo Input has been designed to handle the sig nals from just about any bass with either passive pickups or with hotter pickups if y our bass has active electronics (that is, if it has a battery).
7 Guided T our - F ron t P anel 8. BRITE (control knob ) – This knob set the amount of high frequency tone control used to drive the harmonics in the Bass Attack Overdriv e.
8 Guided T our - Rear P anel A. AC PO WER (inlet) - Use the supplied grounded A C pow er cord to c onnect your Hydrive Combos amplifier to mains po wer .
9 Setting Up and Using Y our Hartke Hydriv e C ombo Bass Amplifier Setting up your Hartke H ydrive C ombo Bass Amplifier is a simple procedure which takes only a f ew minutes: 1. Remove all packing materials (save them in case of need for future service) and decide where the amplifier is to be physically placed .
8. Adjust the Bass, T reble and Graphic Equaliz er controls to tast e. ( When you get a grea t setting that complement's your instrument and pla ying style, it’ s a good idea to write it down f or future use.
11 12. If you need to connect the Hydrive Combo to a P A system or a recording mixing c onsole, connect a cable between the rear-panel Direct Out and a Line -level input on the mix er . (See E on page 8 in this manual for more inf ormation on the use of the Hydrive Combo Dir ect Out).
12 12 The E ffect of the Shape Con trol The Hydrive's unique Shape contr ol enables the sound of your bass instrument to be enhanced a t the touch of a button. When the front panel Shape switch is pressed in, a special equalization curve is activated that is designed to impro ve the sound of most electric bass instruments.
13 Using the Bass A ttack O ver driv e The Hydrive combos f eature Hartke’ s Bass Attack Overdrive circuit allo wing you to add a little tube type overdrive , some edgy dirt or all out fuzz. The Bass A ttack Overdrive operates with thr ee controls; the rst is Harmonics, which is used t o set the amount of over drive.
14 Using E qualization The Hartke Systems Hydrive Combos Bass Amplifier gives you enormous con trol over shaping the sound of your bass, using a pr ocess called equalization .
15 In many instances, the best wa y to deal with equalization is to think in terms of which frequency areas you need to attenua te, as opposed to which ones y ou need to boost.
16 Hydriv e Combo Sample Settings The Hydrive combos are po werful bass amps with a lot of personality. The ampliers oer bassists a wide range of sounds and after playing just a short time; you’ll nd the tone that's perfectly suited for your pla ying style and your sound.
17 Hydriv e Combo Sample Settings.
18 Hydriv e Combo Setting T emplate.
19 Hydriv e Combo Setting T emplate.
20 Rated Output Po wer (@ 1 kHz, 4 ohm, 1% THD) 250 watts Rated Input Lev el (@ 1 kHz) -20 dBu T otal Harmonic Distortion (@ 1 dB below rated output, 1 kHz typical) 0.
.
45 Gilpin Av enue Hauppauge, New Y ork 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) F ax: 631-784-2201 www.hartke.com Hartke Hartke.
An important point after buying a device Samson 210C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Samson 210C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Samson 210C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Samson 210C you will learn all the available features of the product, as well as information on its operation. The information that you get Samson 210C will certainly help you make a decision on the purchase.
If you already are a holder of Samson 210C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Samson 210C.
However, one of the most important roles played by the user manual is to help in solving problems with Samson 210C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Samson 210C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
