Instruction/ maintenance manual of the product Prestige 128 -5264A Audiovox
Go to page of 16
IMPORT ANT ! In order to provide you and your vehicle with the highest level of security , this system is equipped with a dual mode Anti Hi-Jack feature.
Page 2 ARMING THE SYSTEM - ACTIVE 1. T urn of f the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and release the ARM / DISARM button on the keychain transmitter . Red dash mounted L.E.D. begins to flash slowly .
This serves as a visual deterrent to the potential thief. The L.E.D. is a very low current bulb, and will not cause the vehicle’s battery to drain, even when left unattended for extended periods.
Page 4 was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature. If the L.E.D. is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors.
1. S tart with the valet switch in the off position, then turn the ignition key on then off. 2. Within 10 seconds, move the valet switch to on then of f three times. 3. If the chirps were on before you started, then you will hear 2 chirps indicating they have been turned off.
This initial flashing of the LED allows the operator , if Hi-Jack mode is inadvertently triggered, the time to disable the Hi-Jack mode before the siren sounds.This is ac- complished by pressing the hidden Anti Hi-Jack override button. Stage 2 For the next 30 seconds in 10 second intervals, the siren will emit a single chirp.
1. T urn off the ignition switch. 2. Press the hidden Hi-Jack enable/override switch one time. The LED turns on for 5 seconds indicating that the secured mode has successfully be entered. 3. Exit the vehicle, close all doors, and arm your security system using the keychain trans- mitter .
Page 8 APS-25HJ SYSTEM FUNCTIONS A T A GLANCE DASH L.E.D. INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH...P AUSE = INTRUSION ZONE 3 2 FLASH...P AUSE = INTRUSION ZONE 2 NOTE: Slow flash while ignition switch is on indicates that the Hi-Jack mode has been triggered.
Page 9 Modelo APS-25HJ Manual del Propietario Sistema de seguridad con control remoto de 2 botones y función antirrobo en presencia del conductor CARACTERÍSTICAS: Dos transmisores programables d.
Page 10 ACTIV ACIÓN DEL SISTEMA - MODO ACTIVO 1. A pague el motor , salga del vehículo y cierre todas las puertas y las tap as del capó y el baúl. 2.
Page 11 visual para un posible ladrón. El indicador L.E.D. es una bombilla de muy poca corriente que no agotará la batería del vehículo, aun cuando se la deje encendida durante períodos prolongados.
Page 12 hubo algún intento de intrusión a través de alguna de las puertas del vehículo. Estos indicadores de advertencia de intrusión están almacenados en la memoria del siste- ma y solamente se borrarán cuando se encienda la llave de contacto.
Page 13 apague la llave de contacto. 2. A los 10 segundos, mueva el interruptor valet a las posiciones de encendido y apagado tres veces. 3. Si los chirridos estaban conectados antes de empezar , entonces oirá un chirrido que le indica que los está desconectando.
Page 14 el ajuste de la hora de inicio que está indicado en la última hoja de este manual). El indica- dor L.E.D. comienza a destellar por 15 segundos. Este destello inicial del indicador L.E.C. le da tiempo al conductor , si se dispara por accidente la modalidad antirrobo, p ara desactivar la modalidad antirrobo antes de que suene la sirena.
Page 15 MODALIDAD FIJA DE FUNCIONAMIENTO Esta modalidad fija de funcionamiento está disponible, independientemente de que la fun- ción antirrobo esté activada o no. La modalidad fija se usa en aquellos lugares en que el conductor del vehículo sea atacado al volver a su automóvil.
Page 16 INDICADORES L.E.D. DEL T ABLERO DESTELLO RAPIDO = ACTIV ACION P ASIV A DESTELLO LENTO = ACTIV ADO AP AGADO = DESACTIV ADO ENCENDIDO CONTINUO = MODO V ALET 3 DESTELLOS .
An important point after buying a device Audiovox Prestige 128 -5264A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox Prestige 128 -5264A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox Prestige 128 -5264A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox Prestige 128 -5264A you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox Prestige 128 -5264A will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox Prestige 128 -5264A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox Prestige 128 -5264A.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox Prestige 128 -5264A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox Prestige 128 -5264A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
