Instruction/ maintenance manual of the product S281SC Saleen
Go to page of 12
= SALEEN SPEEDLAB S281SC REAR WING KIT INSTALLATION MANUAL: 2005 Mustang P/N: 10-8002-C11998B Saleen Performance, Inc. 76 Fairbanks Irvine, CA 92618 949-597-4900 www.
2.
3 IF YOU ARE NOT EXPERIENCED IN THE AREA OF AUTOMOTIVE MECHANICS, WE STRONGLY URGE THAT YOU REFER THIS INSTALLATION TO A CERTIFIED INSTALLER OR TECHNICIAN.
4 Saleen Speedlab S281SC Rear Wing Kit Installation Guide for 2005 Mustang Thank you for buying the Saleen Speedlab S281SC Rear Wing Kit for the 2005 Mustang.
5 Please Check That All of The Follo wing Parts, In Their Specified Quantities, Are In The Box You Received From Saleen: OBTAIN THE FOLLOWING TOOLS: • Drill • 1/8” bit • 5/16” bit • Torque.
6 Order of Operations: 1. The two boxes in Figure 1 show the location of the holes that will be drilled in the deck lid to mount the rear wing. 2. Figure 2 shows the wing as it is shipped, with the studs installed. The studs will go into the holes you will drill in the deck lid.
7 Figure 5 1 ¼” Figure 6 7/8” 1 ½” 7/8” Front of car Front of car Figure 7 Studs Holes in deck lid 5. Mark each rearward, outboard hole location for the wing studs with a center punch.
8 Figure 8 10. Secure the deck lid in an open position so it is a few inches above the tail light assemblies – this is to p rotect all trunk innards during hole dr illing. (Figure 8) 11. Drill 1/8” pilot holes at the marked locations in the deck lid, then open the holes up to 5/16”.
9 14. Using paint thinner, clean around the bottom side of the wing in the raised portion around the studs (clean the area indicated by the dotted line in Figure 13). 15. Apply automotive adhesion promoter (3M# 06396) around the base of the studs; follow the dotted line in Figu re 13.
10 Figure 17 Figure 16 Figure 18 Studs Holes in deck lid 18. Before installing the wing, make sure the number of studs in the wing equals the number of holes drilled in the deck lid. Do a test fit to m ake sure all the holes li ne up. (Figure 16) 19. Apply adhesive promoter to the top of the deck lid around both sets of four holes.
11 Figure 19 Figure 20 SC Wing Driver side Acorn nuts Deck lid 22. With the deck lid just partially open (so the wing doesn’t fall out), secure four outboard studs of wing (two per side) with one washer (00- 9004-C11804*) and one acorn hex nut (00-9003-C11802*; use red Loctite).
12 Fi g ure 24 Figure 23 Tighten nut in here 26. Place one washer (00-9004- C11804*) and one hex nut (00- 9003-C11803*; use red Loctite) over each (2 total) of the furthest inboard studs (those that a.
An important point after buying a device Saleen S281SC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Saleen S281SC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Saleen S281SC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Saleen S281SC you will learn all the available features of the product, as well as information on its operation. The information that you get Saleen S281SC will certainly help you make a decision on the purchase.
If you already are a holder of Saleen S281SC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Saleen S281SC.
However, one of the most important roles played by the user manual is to help in solving problems with Saleen S281SC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Saleen S281SC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
