Instruction/ maintenance manual of the product TS1351 Ryobi
Go to page of 28
OPERA T OR'S MANUAL 10 in. (254 mm) Compound Miter Saw Model TS1351 - Double Insulated Your new Miter Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
Page 2 TABLE OF CONTENTS PRODUCT SPECIFICA TIONS Blade Arbor 5/8 in. (16 mm) Blade Diameter 10 in. (254 mm) Rating 120 volts, 60Hz, AC Only No Load Speed 5000 RPM Input 15 Amperes Net Weight 29.92 lbs. (13.6 kg.) INTRODUCTION Y our saw has many features for making cutting operations more pleasant and enjoyable.
Page 3 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 4 Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your miter saw works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER TOOL.
Page 5 ■ NEVER reach behind, under, or within three inches of the blade and its cutting path with your hands and fingers for any reason. ■ NEVER hand hold a workpiece that is too small to be clamped.
Page 6 SA VE THESE INSTRUCTIONS RULES FOR SAFE OPERA TION ■ STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired.
Page 7 UNP ACKING ■ Lift the saw arm by the handle. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap. ■ Examine all parts to make sure no breakage or damage has occurred during shipping.
Page 8 The following items are included with your Compound Miter Saw: ■ 10 in. (254 mm) Saw Blade ■ Miter Lock Handle ■ Dust Bag ■ Dust Guide ■ Stop Block ■ Small Wing Screw ■ Clamp Brac.
Page 9 FEA TURES KNOW YOUR COMPOUND MITER SAW See Figure 2. Before attempting to use your saw, familiarize yourself with all operating Features and Rules for Safe Operation. W ARNING: Do not allow familiarity with your saw to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.
Page 10 1 . 1 5 30 4 5 2 2 .5 31.62 3 0 45 3 1 . 6 2 FEA TURES BLADE WRENCH / ST ORAGE AREA See Figure 2. A blade wrench is packed with your saw . One end of the wrench is a phillips screwdriver and the other end is a 1/4 in.
Page 11 0 2 2 .5 3 1 .6 22.5 31.6 4 5 45 30 5 1 3 0 15 FEA TURES POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0 ° , 15 ° , 22-1/2 ° , 30 ° , and 45 ° . The 22-1/2 ° and 45 ° positive stops have been provided on both the left and right side of the miter table.
Page 12 1 1 5 30 4 5 3 3 0 45 .5 31.62 1 5 30 22. 5 3 1 . 6 2 4 5 5 1 5 3 0 45 33.9 15 3 0 45 33.9 1 . 15 30 4 5 2 2 . 5 31.6 2 30 4 5 3 1 .6 2 ASSEMBL Y W ARNING: To prevent accidental starting that .
Page 13 1 1 5 3 0 45 3 3 . 9 3 0 45 .5 3 1. 6 2 1 5 3 0 22.5 3 1 . 6 2 4 5 0 1 5 1 5 3 0 45 3 3 .9 3 0 45 .5 31 .62 1 5 30 22 .5 3 1 . 6 2 30 3 1 . 6 2 4 5 TABLE EXTENSIONS See Figures 11, 12, and 13. If you plan to use the stop block, slide the stop block on the back arm of the desired table extension first.
Page 14 ASSEMBL Y TO INSTALL BLADE See Figures 15 and 16. W ARNING: A 10 in. (254 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle.
Page 15 ASSEMBL Y CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard. ■ Tighten blade bolt securely.
Page 16 0 22.5 31 .6 22.5 3 1 .6 45 45 3 0 5 1 30 15 ADJUSTMENTS W ARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury. ■ Push down on the saw arm and pull out the lock pin to release the saw arm.
Page 17 0 22.5 31.6 22.5 31.6 45 45 30 5 1 30 15 45 3 0 1 5 15 3 0 45 3 1 .6 2 2 2. 5 31 .6 2 22.5 45 0 45 3 0 1 5 15 3 0 45 3 1 .6 2 2 2. 5 31.6 2 2 2 .5 45 0 45 3 0 1 5 15 3 0 45 3 1 .6 2 2 2. 5 31.6 2 22.5 45 0 ADJUSTMENTS ■ The edge of the square and the saw blade should be parallel as shown in figure 21.
Page 18 45 3 0 1 5 15 3 0 45 3 1 .6 2 2 2. 5 3 1.6 2 2 2 .5 45 0 45 3 0 1 5 15 3 0 45 3 1 .6 2 2 2. 5 31.6 2 22 .5 45 0 45 3 0 1 5 15 3 0 45 3 1.6 2 2 2. 5 31 .6 2 22.5 45 0 ADJUSTMENTS SQUARING THE BLADE TO THE MITER TABLE See Figures 25 - 27. ■ Unplug your saw.
Page 19 ADJUSTMENTS BEVEL PIVOT ADJUSTMENT ■ Your compound miter saw should bevel easily by loos- ening the bevel lock knob and tilting the saw arm to the left. ■ If movement is tight or if there is play in the pivot, have saw repaired by at your nearest RYOBI AUTHORIZED SERVICE CENTER.
Page 20 1 1 5 3 0 4 5 33.9 30 45 .5 31.62 1 5 30 22.5 3 1 . 6 2 4 5 CUTTING WITH YOUR COMPOUND MITER SAW W ARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece.
Page 21 1 1 5 3 0 45 3 3 . 9 3 0 45 .5 31.62 1 5 30 22.5 3 1 . 6 2 4 5 0 15 0 45 BEVEL SCALE INDICATOR SCREW SCALE INDICATOR OPERA TION ■ Pull out the lock pin and lift saw arm to its full height. ■ Loosen the miter lock handle. Rotate the miter lock handle approximately one-half turn to the left to loosen.
Page 22 0 3 1 5 2 2. 5 0 1 5 30 4 5 22.5 3 1. 6 2 OPERA TION ■ Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 31. W ARNING: To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in.
Page 23 ■ Recheck miter angle setting. Make a test cut in scrap material. ■ Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade.
Page 24 CUTTING COMPOUND MITERS To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much thought and planning made, prior to making your required cut.
Page 25 When setting the bevel and miter angles for compound miters, remember that the settings are interdependent; chang- ing one angle changes the other angle as well. Keep in mind that the angles for crown moldings are very precise and difficult to set.
Page 26 0 2 2 . 5 3 1 .6 22.5 31.6 45 45 3 0 5 1 3 0 15 1 1 5 30 4 5 33.9 3 0 45 .5 3 1 .6 2 1 5 3 0 2 2.5 3 1 . 6 2 4 5 3 45 3 1 . 6 2 4 5 5 3 3 1 . 6 3 1 . 6 4 5 5 3 3 1 .6 4 5 WRONG W ARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence.
Page 27 W ARNING: When servicing, use only identical Ryobi replacement parts. Use of any other part may create a hazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use.
Page 28 972000-956 09-02 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.
An important point after buying a device Ryobi TS1351 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi TS1351 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi TS1351 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi TS1351 you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi TS1351 will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi TS1351, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi TS1351.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi TS1351. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi TS1351 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
