Instruction/ maintenance manual of the product SA720 Ryobi
Go to page of 20
OPERA T OR'S MANU AL CORDLESS DRILL-DRIVER MODEL NOS. SA60 / SA720 20 20 MODEL SA60 MODEL SA720 This new drill has been engineered and manufactured to our Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, the drill will give you years of rugged, trouble-free performance.
Page 2 ■ ■ ■ ■ ■ Introduction .................................................................................................................................................................... 2 ■ ■ ■ ■ ■ General Saf ety Rules ..
Page 3 GENERAL SAFETY R ULES W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injur y . SA VE THESE INSTRUCTIONS WORK AREA ■ K eep your w ork area clean and well lit .
Page 4 GENERAL SAFETY R ULES SPECIFIC SAFETY R ULES SER VICE ■ T ool ser vice m ust be performed onl y b y qualified repair personnel. Ser vice or maintenance performed by unqualified personnel ma y result in a r isk of injury . ■ When servicing a tool, use onl y identical replace- ment parts.
Page 5 IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injur y . ■ Never use a battery that has been dropped or received a sharp blow.
Page 6 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger.
Page 7 DRILL-DRIVER SA60 SA720 Chuck 3/8 in. (10 mm) Keyless 3/8 in. (10 mm) Keyless Motor DC Motor 6.0 Volt DC Motor 7.2 Volt Switch Two Speed Two Speed No Load Speed 300 / 500 RPM 330 / 500 RPM Clutch 24 Positions 24 Positions Charger Input 120 V, 60 Hz, AC only 120 V, 60 Hz, AC only Charge Rate 3-6 Hours 3-6 Hours Torque Maximum 45 in.
Page 8 FEA TURES KNOW YOUR DRILL-DRIVER See Figure 1. Bef ore using this tool, f amiliarize y ourself with all operating f eatures and saf ety requirements. Howe ver , do not let f amiliarity with the tool make you careless . W ARNING: Ex ercise caution when using this tool.
Page 9 20 20 FEA TURES Fig. 1 KEYLESS CHUCK BIT STORAGE AREA TORQUE ADJUSTMENT RING SWITCH TRIGGER LEVEL MODEL SA60 MODEL SA720 KEYLESS CHUCK BIT ST ORAGE AREA TORQUE ADJUSTMENT RING SWITCH TRIGGER LE.
Page 10 5 1 0 Fig. 2 SWITCH TRIGGER REVERSE FORW ARD DIRECTION OF ROT A TION SELECTOR CENTER POSITION (LOCK) REVERSIBLE See Figure 2. This tool is reversible.
Page 11 20 WRONG ADJUSTMENTS Fig. 4 INSTALLING BITS See Figures 3 and 4. ■ Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 9. ■ Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Page 12 20 20 ADJUSTABLE TORQUE CLUTCH See Figure 5. When using your drill-driver for various driving applications, it becomes necessary to increase or decrease the torque in order to help prevent the possibility of damaging screw heads, threads, workpiece, etc.
Page 13 W ARNING: Do not allow f amiliar ity with the drill to make y ou care- less. Remember that a careless fraction of a second is sufficient to inflict sev ere injur y . CHARGING YOUR DRILL-DRIVER This tool has been shipped in a low charge condition to prevent possible problems.
Page 14 5 1 0 5 1 0 Fig. 9 DIRECTION OF ROT A TION SELECTOR SWITCH TRIGGER IMPORTANT INFORMATION FOR RECHARG- ING HOT BATTERIES When using your drill-driver continuously, the batteries be- come hot. You should let the batteries cool down for approxi- mately 30 minutes before attempting to recharge.
Page 15 20 Fig. 11 SWITCH See Figure 11. To turn your drill ON , depress the switch trigger. To turn it OFF , release the switch trigger. Your drill has a two-speed feature in the switch. Depress the switch trigger halfway for driving screws at low speed.
Page 16 2 0 20 OPERA TION Fig. 13 LEVEL DRILLING See Figure 13. A conv enient ne w f eature pro vided with y our drill is a lev el. It is recessed in the motor housing on top of your drill. It can be used to keep drill bit le vel during drilling operations.
Page 17 20 MALLET KEYLESS CHUCK CHUCK JA WS HEX KEY WRENCH Fig. 14 Fig. 15 Fig. 16 MAINTENANCE 20 20 W ARNING: When ser vicing use only identical Ry obi replacement par ts. Use of any other par ts ma y create a hazard or cause product damage. Do not abuse po wer tools .
Page 18 R E C Y C L E 1 . 8 0 0 . 8 2 2 . 8 8 3 7 RBRC Ni Cd ™ MAINTENANCE ■ Open the chuck ja ws and remov e the he x k ey . Remov e the chuck scre w b y tur ning it in a cloc kwise direction. See Figure 15. NO TE: The screw has left hand threads.
Page 19 MAINTENANCE BATTERY REMOVAL, PREPARATION FOR RECYCLING MODEL SA60 See Figures 17 and 18. T O REMO VE: ■ Lock s witch tr igger by placing the f orward/rev erse switch in center position. See Figure 9. ■ Remov e battery cover from bottom of drill handle b y depressing and pushing cov er in the direction of the arro w .
983000-332 6-03 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 in the United States for your nearest Authorized Service Center.
An important point after buying a device Ryobi SA720 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi SA720 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi SA720 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi SA720 you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi SA720 will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi SA720, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi SA720.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi SA720. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi SA720 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
