Instruction/ maintenance manual of the product RZ 100 Ryobi
Go to page of 11
RZ 100 For Parts or Installation Assistance Contact INC. phone: 1-866-266-1293 fax: 1-515-266-2122 2729 Delaware Ave, Des Moines, IA. 50317 1 2 3 Craftsman DeWalt DW 625 DeWalt DW 621 Hitachi M12V Hit.
This instruction manual covers several differ ent makes and models of plunge routers. The instructions ar e written for a person with some mechanical ability . If you understand the parts and operation of a plunge r outer , installing the Router Raizer is not difficult.
© 2000-2005 Router T echnologies All Rights Reserved Page 2 READ THIS P AGE BEFORE INST ALLA TION FULL SIZE P AR TS DIAGRAM ON BACK OF THIS P AGE ( P AGE 3 ) 3. Multiple Parts The Router Raizer is a universal kit containing many parts you will not install into your router .
RZ 100 Parts Diagram Caution: Before and during installation of Router Raizer make sure power switch is in the off position and tool is disconnected from power source to avoid accidental starting of the tool which may result in personal injury .
Page 4 METHOD #1 ( Drilling 3/4" Pocket in Back of Insert Plate requir es min 3/8" thick plate ) Using the #46 Locating Pin Use this pin to simplify locating the Router Raizer access hole required through the original subbase or router table.
Page 5 Pr eparing and Drilling Router T able T op Method #2 (A ) and ( B ) METHOD #2 ( A ) Black Rubber spacer METHOD #2 ( B ) Routers Original Sub Base METHOD #2 ( A ) Black Rubber spacer METHOD #2 (.
Using Paper Drilling T emplate T roubleshooting © 2000-2005 Router T echnologies All Rights Reserved Page 6 Refer to pages 4,5,6 before using template Additional T emplates Available on Website Router Raizer Access Hole 3/4" reference circle for drilling the routers original subbase only .
Router Raizer Use Instructions Page 7 Using Handheld Using in a Router T able Caution: Always make sure router switch is in the off position, and tool is disconnected from power source when performing.
Page 8 Craftsman T ools Required: T wo 11/16" wrench’ s , phillips screwdriver , 5/16" drill bit, drill, hacksaw , Router Raizer Parts Required: ( see page 1) #1, #7, #12, #13, #14,/( thr ee #15 ) #16, #17, #18, #20, #21, #22, #23, #24, #26, #27, #28, #29, ( #30,#31,#46 for router table installation ).
Page 9 Craftsman 3. With router completely plunged and locked., center long drive nut and housing bushing assembly on #1 mainshaft. Secur e using two 11/16" wrenches. 6. With plunge lock disengaged, make sure plunging action operates smoothly , If not, loosen drive nut re-center and retighten.
Page 10 © 2000-2005 Router T echnologies All Rights Reserved Subbase mounting holes Router table fence reference line Note: Cross lines for locating and drilling holes are accurate. The illustration of subbase may vary slightly in size and design, but is accurate enough for cutting the rubber spacer if required.
An important point after buying a device Ryobi RZ 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi RZ 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi RZ 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi RZ 100 you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi RZ 100 will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi RZ 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi RZ 100.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi RZ 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi RZ 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
