Instruction/ maintenance manual of the product C358 Ryobi
Go to page of 20
OPERA TOR’S MANUAL 14 in. Abrasive Cut-Of f Machine C358 SA VE THIS MANUAL FOR FUTURE REFERENCE Y our cut-off machine has been engineer ed and manufactured to Ryobi’ s high standard for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-fr ee performance.
2 T ABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 � n General Safety Rules ....................
3 GENERAL SAFETY RULES into moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Also wear protective hair covering to contain long hair . n AL WA YS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impact- resistant lenses; they ar e NOT safety glasses.
4 GENERAL SAFETY RULES SPECIFIC SAFETY RULES n NEVER USE IN AN EXPLOSIVE A TMOSPHERE. Normal sparking of the motor could ignite fumes. n INSPECT TOOL CORDS PERIODICALL Y . If damaged, have repaired by a qualified service technician at an authorized service facility .
5 SPECIFIC SAFETY RULES n AL W A YS EASE THE ABRASIVE WHEEL AGAINST THE MA TERIAL when starting to cut. A harsh impact can break the wheel. n BEFORE CUTTING press the trigger switch and allow the cut-off wheel to r each full speed.
6 SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpr eta- tion of these symbols will allow you to operate the tool better and safer .
7 SYMBOLS SERVICE Servicing requir es extr eme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the pr oduct to your near est AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts.
8 SPEED AND WIRING The no-load speed of this tool is approximately 3,900 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’ s horsepower rating. A line intended only for lights cannot pr operly carry a power tool motor .
9 FEA TURES PRODUCT SPECIFICA TIONS n Input .............................. 120V , 60 Hz, AC Only ,15 Amps n No Load Speed.............................................. 3,900/min. n Arbor Diameter .......................................................
10 FEA TURES LOCK-ON BUTTON See Figure 3. T h e c u t - o f f m a c h i n e i s e q u i p p e d w i t h a l o c k - o n feature which is convenient when continuous cutting for extended periods of time is r equired.
11 LOOSE P ARTS ASSEMBL Y UNP ACKING This product has been shipped completely assembled. n Carefully lift machine from the carton by the carrying handle and the machine base, and place it on a level work surface. NOTE: This tool is heavy . T o avoid back injury , lift with your legs, not your back, and get help when needed.
12 REMOV AL / INST ALLA TION OF WHEEL TO REMOVE See Figure 5. n Unplug the cut-off machine. n Push down on machine arm and r emove transport chain from hook on motor housing to r elease machine arm. n Raise machine arm to its full raised position. Be cautious when raising, machine arm is spring loaded.
13 Fig. 6 Fig. 7 Fig. 8 ADJUST ABLE FENCE ADJUST ABLE FENCE FENCE SCALE VISE CLAMP ADJUST ABLE FENCE ASSEMBL Y ADJUST ABLE FENCE See Figure 6. The adjustable fence is located at the rear of the cut-off machine. As mentioned previously , it is used along with the vise clamp to provide a clamp for holding the workpiece securely when making cuts.
14 Fig. 9 Fig. 10 QUICK LOCK-RELEASE LEVER WITH THREADS NOT ENGAGED VISE CLAMP VISE CRANK HANDLE VISE SCREW VISE CLAMP VISE CRANK HANDLE QUICK LOCK- RELEASE LEVER WITH THREADS ENGAGED n Usi ng the hex wren ch suppli ed, secur ely tight en hex hea d bolts.
15 Fig. 11 CAUTION: Do not start the abrasive cut-of f machine without check- ing for interfer ence between the wheel and the machine base support. Damage may result to the wheel if it strikes the machine base support during operation of the machine. � n Tighten the depth stop bolt with the hex wrench provided.
16 MA TERIAL TO BE CUT POWER SUPPL Y Before operating the cut-off machine, check the power supply and make sure it meets the requir ements listed on the tool’ s data plate. A substantial voltage drop will cause a loss of power and machine overheating.
17 OPERA TION Fig. 14 Fig. 15 MACHINE BASE MACHINE ARM SWITCH TRIGGER MA TERIAL TO BE CUT ADJUST ABLE FENCE VISE CLAMP ADJUST ABLE FENCE MA TERIAL TO BE CUT VISE CRANK HANDLE the wheel to build up to full speed before letting it come into contact with the material to be cut.
18 MAINTENANCE WARNING: When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shi eld s du ring pow er tool oper ati on or when blow ing dust .
19 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Machine does not start 1. Power cord not plugged in. 1. Plug in cord. 2. Power cor d is damaged. 2. Have the cord r eplaced at your nearest authorized service center . 3. Cir cuit breaker is tripped. 3. Reset circuit br eaker .
983000-607 10-04 OPERA TOR’S MANUAL 14 in. Abrasive Cut-Of f Machine C358 • SER VICE Now that you have pur chased your tool, should a need ever exist for repair parts or service, simply contact your near est Ryobi Authorized Service Center . Be sure to provide all pertinent facts when you call or visit.
An important point after buying a device Ryobi C358 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi C358 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi C358 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi C358 you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi C358 will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi C358, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi C358.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi C358. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi C358 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
