Instruction/ maintenance manual of the product 767rj Ryobi
Go to page of 22
767rj 2-Cycle Gas T rimmer OPERA TOR’S MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. or 1-800-265-6778 in CANADA www.ryobi.com IMPORT ANT MANUAL DO NOT THROW AW A Y.
INTRODUCTION T ABLE OF CONTENTS 2 THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-to-under- stand operating instructions.
CALIFORNIA EMISSION REGULA TIONS 3 SP ARK ARRESTOR W ARNING! RULES FOR SAFE OPERA TION NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington.
RULES FOR SAFE OPERA TION 4 READ ALL INSTRUCTIONS BEFORE OPERA TING • Read the instructions carefully. Be familiar with the controls and proper use of the unit. • Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.
RULES FOR SAFE OPERA TION 5 • Do not touch the engine or muffler. These parts get extremely hot from operation. When turned off they remain hot for a short time. • Do not operate the engine faster than the speed needed to cut, trim or edge. Do not run the engine at high speed when not cutting.
SYMBOL MEANING • PRIMER BULB Push primer bulb, fully and slowly , 5 to 7 times. • UNLEADED FUEL Always use clean, fresh unleaded fuel. • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate without the cutting attachment shield in place.
RULES FOR SAFE OPERA TION 7 KNOW YOUR UNIT APPLICA TIONS • Cutting grass and light weeds. • Decorative trimming around trees, fences, etc. Handle Hardware Primer Bulb Air filter/Muffler Cover Fuel.
6. While holding the unit in the operating position (Fig. 3), position the J-handle to the location that provides you the best grip. 7. Tighten the clamp screws evenly, until the J-handle is secure. INST ALLING THE CUTTING A TT ACHMENT SHIELD Use the following instructions if the cutting attachment shield on your unit is not installed.
ASSEMBL Y INSTRUCTIONS 9 OIL AND FUEL INFORMA TION WARNING: Gasoline is extr emely flammable. Ignited V apors may explode. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the tank. Keep sparks and open flames at a distance from the ar ea.
ST ARTING/STOPPING INSTRUCTIONS 10 4. Place the choke lever in the FULL choke position ( A ) (Fig. 8). 8. If the engine does not start, repeat steps 4 through 7. NOTE: If the engine floods while trying to start, place the choke lever in the RUN position ( C ) (Fig.
11 OPERA TING INSTRUCTIONS Fig. 10 Fig. 11 Each time the head is bumped, about 1 inch (25.4 mm.) of trimming line is released. A blade in the cutting attachment shield will cut the line to the proper length if excess line is released. For best results, tap the Bump Head ™ on bare ground or hard soil.
WARNING: Always use the corr ect line length when installing trimming line on the unit. The line may not release pr operly if the line is too long. 2. Hold the outer spool and turn the inner reel counterclockwise to line up the arrows on the outer spool and inner reel (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 13 Line Locking Hole Trimming Line Line Loading Hole Eyelet 5. Insert the line into the locking hole (Fig. 15). Do not push the line more than 1/2 inch (12.7 mm.) into the line locking hole. When inserted correctly the line will form a small loop (Fig.
MAINTENANCE AND REP AIR INSTRUCTIONS 14 2. Pull out the bump knob, spring, and foam seal (Fig. 19, Pg. 13). 3. Pull the inner reel with existing line from the outer spool (Fig. 19, Pg. 13). 4. Remove any existing line from the inner reel before cleaning.
MAINTENANCE AND REP AIR INSTRUCTIONS 15 Fig. 25 Fig. 26 Fig. 27 4. Apply enough clean SAE 30 oil to lightly coat the filter (Fig. 27). Air Filter 3. Wash the filter in detergent and water (Fig. 26). Rinse the filter thoroughly. Squeeze out excess water.
MAINTENANCE AND REP AIR INSTRUCTIONS 16 0.020 in. (0.5 mm.) Fig. 30 CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable through the Air filter/Muffler cover (Fig. 29). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.
CLEANING AND STORAGE 17 TRANSPORTING • Allow the engine to cool before transporting. • Secure the unit while transporting. • Drain fuel from unit. • Tighten fuel cap before transporting. CLEANING WARNING: T o avoid serious personal injury , always turn your trimmer off and allow it to cool before you clean or do any maintenance on it.
TROUBLESHOOTING 18 CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Replace the inn.
SPECIFICA TIONS 19 Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 2-Cycle Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTES 20.
21 The California Air Resources Board and Ryobi Outdoor Products (ROP), are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE TWO (2) YEAR WARRANTY PERIOD OR NINETY (90) DAYS FOR PRODUCTS USED FOR ANY COMMERCIAL PURPOSE. ACCORDINGLY, ANY SUCH IMPLIED WARRANTIES INCLUDING .
An important point after buying a device Ryobi 767rj (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi 767rj yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi 767rj - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi 767rj you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi 767rj will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi 767rj, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi 767rj.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi 767rj. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi 767rj along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
