Instruction/ maintenance manual of the product 310r Ryobi
Go to page of 20
1 IMPOR T ANT FOR ST AR TING INSTR UCTIONS REFER TO P A GE 10 IMPOR T ANT MANU AL DO NO T THR O W A W A Y OPERA T OR’S MANU AL Model 310r Blo wer Model 310BVr Blo wer V ac.
2 I. California Emission Regulations ................................3 II. Safety W ar nings ......................................................3-5 A. Operational ........................................................3-4 B. Safety and International Symbols .
3 CALIFORNIA EMISSION REGULA TIONS SAFETY W ARNINGS FUELING AND PRE-OPERA TION • Gasoline is extremely flammable and its vapors can explode if ignited. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the fuel tank.
4 SAFETY W ARNINGS (Continued) unit is running to avoid flying debris. • Avoid situations that could catch the collection bag on fire. Do not operate near an open flame. Do not vacu- um warm ash from fir eplaces, barbeque pits, brush piles, etc. Do not vacuum discarded cigars or ciga- rettes unless the cinders ar e completely cool.
5 SAFETY W ARNINGS (Continued) • UNLEADED FUEL. Always use clean, fresh unleaded fuel. • PRIMER BULB. Push primer bulb, fully and slowly , 5 to 7 times. • CHOKE CONTROL. FULL CHOKE position. • CHOKE CONTROL. P ARTIAL CHOKE position. • CHOKE CONTROL.
W ARNING Rotating impeller blades can cause severe injury . Do not attempt to convert the unit while the engine is running to avoid serious personal injury . Do not put hands or any other object into the vacuum tubes while they are installed on the unit.
7 ASSEMBL Y INSTR UCTIONS (Continued) INST ALLING THE AD APTER ONTO THE UPPER V A CUUM TUBE - (OPTIONAL FOR MODEL 310r) NOTE: Do not install while unit is running. 1. T ur n the blower upside down as shown in Fig. 4. Hold the blower between your knees to install the adapter and vacuum tubes.
8 INST ALLING THE V A CUUM TUBES - (OPTIONAL FOR MODEL 310r) NOTE: Do not install tubes while unit is running. 1. Align the arrow on the lower vacuum tube with the arrow on the upper vacuum tube (Fig. 12). 2. Grasping the lower vac tube firmly with both hands, push the lower vac tube into the upper vac tube.
W ARNING Remove fuel cap slowly to avoid injury from fuel spray . NOTE: BE SURE TO READ THESE INSTRUCTIONS CAREFULL Y BEFORE A TTEMPTING TO ST AR T OR OPERA TE THIS UNIT . Using old or improper oil or fuel, or improperly mixing the oil and fuel can cause engine damage.
10 5. SQUEEZE THE THROTTLE TRIGGER TO FULL THROTTLE. Hold the trigger in this position. 6. PULL THE ST AR TER ROPE BRISKL Y until you hear the engine sounds like it wants to run (normally 2 to 5 pulls). 7. PLACE THE CHOKE LEVER IN THE "P AR TIAL" POSITION.
11 W ARNING DO NOT OPEN THE DOOR WITH THE ENGINE RUNNING! T o do so can result in serious personal injury caused by contact with the rotating blades. NOTE: Do not wear rubber or any other insulated gloves to avoid static electricity shock. 1. Move the unit slowly back and forth over the debris to be vacuumed (Fig.
12 NOTE: CLEAN AND RE-OIL THE AIR FIL TER EVER Y 10 HOURS OF OPERA TION . Y our unit's air filter is one of the most important areas to maintain. If it is not maintained as follows, you will void the warranty . 1. Press the filter cover with your finger and r emove the cover from the air filter base (Fig.
13 Fig. 26 Fig. 27 Fig. 28 6. Carefully r einstall the air filter . Be sure the filter is sealed properly befor e placing it on the air filter base (Fig. 28). 5. Squeeze the filter to spread the oil (Fig. 27). MAINTEN ANCE AND REP AIR INSTR UCTIONS (Continued) 4.
3. Initial High Speed Mixture and Idle Speed Mixtur e Needle Settings: Insert the screwdriver thr ough the hole at the back of the top handle (Fig. 32). T ur n both the high speed mixture and idle speed mixtur e needles out (counterclockwise) until the limiter caps stop .
NOTE: If the carburetor adjustments do not help the unit to run properly , contact your authorized service dealer . 15 MAINTEN ANCE AND REP AIR INSTR UCTIONS (Continued) INSPECTING/CLEANING THE MUFFLER The muffler should be r emoved every 25 hours of opera- tion to inspect for excessive carbon build-up.
16 MAINTEN ANCE AND REP AIR INSTR UCTIONS (Continued) If carbon build-up cannot be cleaned, replace the muf fler . 3. Inspect the muffler mounting holes for elongation. Replace the muffler if the holes ar e elongated. Muffler Reassembly 1. Install a new gasket*.
17 ENGINE Manufacturer ..........................Ryobi Outdoor Pr oducts, Inc. T ype ..........................................2-Cycle, Air -Cooled Displacement ............................31 cc (1.9 cu. in) Bore ......................................
18 TR OUBLESHOO TING PR OBLEM CA USE A CTION Engine Will Not Start Choke in incorrect position Refer to starting/stopping instructions on page 10 Empty fuel tank Fill fuel tank Primer bulb wasn't.
19 The California Air Resources Board and Ryobi America Corp. (RAC), is pleased to explain the emission control system warranty on your 1995 lawn and garden equipment engine. In California, new lawn and garden equipment engines must be designed, built and equipped to meet the State's stringent anti-smog standards.
20 Operator's Manual Part Number 181146 3/95 R YOBI AMERICA COR P . warrants each new R YOBI P r oduct for two (2) years acco r d- ing to the following terms. This warranty extends to the original retail purchaser only and commences on the date of original retail purchase.
An important point after buying a device Ryobi 310r (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ryobi 310r yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ryobi 310r - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ryobi 310r you will learn all the available features of the product, as well as information on its operation. The information that you get Ryobi 310r will certainly help you make a decision on the purchase.
If you already are a holder of Ryobi 310r, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ryobi 310r.
However, one of the most important roles played by the user manual is to help in solving problems with Ryobi 310r. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ryobi 310r along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
