Instruction/ maintenance manual of the product ST2-XM Russound
Go to page of 40
.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER - SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
T ABLE OF CONTENTS Pr oduct Introduction ..........................................................................................................4-5 Component Guide ST2-XM Front Panel .................................................................
4 INTRODUCTION DESCRIPTION Thank you for choosing the Russound ST2-XM Smart T uner . Whether you are adding radio to an existing system, expanding a CAi Series system or taking advantage of the CAV6.6’ s robust RNET™ communication link, the ST2-XM T uner is designed to meet your needs.
5 INTRODUCTION frequency or channel, pr eset names and AM/FM band or XM is displayed on UNO-S2 keypads. An additional RNET device can be connected to an existing ST2 by using the Link Out of the first unit into the Link In of the second unit. Before using the ST2-XM tuner with the CAV6.
6 COMPONENT GUIDE ST2-XM FRONT P ANEL XM AM/FM XM AM/FM 64 : The Groove 64 : The Groove MAIN POWER SWITCH - T urns power on and off POWER ON/OFF LED - Indicates power on or off REMOVABLE COVER LENS - .
7 RS-232 INTERFACE 12VDC 1.5A I N O UT NEWMARKET, NH U.S.A. ST2 Smart Tuner LINK K EYP AD P ORTS Serial# MADE IN KOREA T UNER 1 FM C OAX L OOP A NTENNA IR LR A UDIO O UTPUT IR LR A UDIO O UTPUT T UNER.
8 TUNE TUNE FAV 1 SEEK ST/ MONO LOC/ DX SEEK TUNE TUNER 1 TUNER 2 4 M E M B A N K 123 56 789 0 PWR MEM TUNE AM/FM FAV 2 OK POWER - Puts the tuner in/out of standby mode TUNER CONTROL - Select TUNER 1 .
9 ST2-XM SETUP AND CONNECTIONS BASIC CONNECTIONS Power T o power the tuner , connect the 12VDC external power supply by inserting the power supply jack into the power supply connection on the tuner’ s rear panel. Audio Output Connect one end of a dual RCA audio cable to the T uner 1 Audio Output connection.
10 ST2 T uner CA V6.6 UNO-S2 keypads RCA Cable 64:The Groove Source Connections with CA V6.6 Contr oller/Amplifier (RNET System) The diagram depicts a typical setup using the ST2-XM T uner with a CAV6.6 amplifier . Each tuner in the ST2 unit must be connected as a separate source for audio inputs.
11 ST2-XM SETUP AND CONNECTIONS CAi SERIES AND A-BUS CONNECTIONS RS-232 INTERFACE 12VDC 1.5A I N O UT NEWMARKET, NH U.S.A. ST2 Smart Tuner LINK K EYPAD P ORTS Serial# MADE IN KOREA T UNER 1 FM C OAX L OOP A NTENNA IR LR A UDIO O UTPUT IR LR A UDIO O UTPUT T UNER 2 A NTENNA 1 R L 2 1 R L 2 34 CA6.
12 ST2-XM SETUP AND CONNECTIONS ANTENNA CONNECTIONS Connecting an Indoor and Outdoor Antenna The diagram above depicts a typical setup using the ST2-XM T uner with the included XM antenna, FM antenna and AM loop antenna. Also shown are two outdoor antenna options (not included).
13 ST2-XM SETUP AND CONNECTIONS ANTENNA CONNECTIONS Gr ounding an Outdoor Antenna If the tuner is used with an outdoor antenna, the antenna must be grounded against static char ges and voltage sur ges. Consult the instructions that came with the antenna or contact the antenna manu- facturer for pr oper installation instructions.
XM Radio Activation XM Radio is over 100 channels of radio broadcasts with the signal deliver ed by satellite and (depend- ing on location) transferred by terr estrial antennas. The radio is a subscription-based service with a monthly provider fee and an activation char ge.
15 ST2-XM OPERA TION XM RADIO MODES XM Radio Modes There ar e four user “modes” for selecting music and viewing music information on the XM T uner: Preset (default or normal) Category Search Now Playing Display Prefer ences . These modes are accessed thr ough cer tain button and key presses fr om the tuner panel, remote controls and keypads.
16 ST2-XM OPERA TION XM RADIO MODES ST2-XM ST2-RC ST2-KP UNO-S2 UNO-LRC1 Preset Mode Next Preset MEM Previous Pr eset MEM Next Bank Hold Hold Hold Previous Bank Hold Hold Hold Channel Up TUNE Channel Down TUNE Preset (default) Mode This is the normal operating mode of the XM tuner .
17 Category Search Mode ( 1 1 . . C C A A T T S S E E A A R R C C H H ) XM Radio is or ganized by Channel Category (e.g., Rock, Country, News ). W ithin each category is a series of channels (e.g., T op T racks, Bluegrass Junction, XM Classics). Channel selection in this mode is refined to scr olling only those channels in the selected category .
18 ST2-XM ST2-RC ST2-KP UNO-S2 UNO-LRC1 Display Prefer ence Mode OK Next Display Prefer ence TUNE MEM MEM Previous Display Pr eference TUNE MEM MEM ST2-XM OPERA TION XM RADIO MODES Now Playing Mode ( 2 2 . . N N O O W W P P L L A A Y Y N N G G ) This mode displays information about the current XM selection.
19 Front Panel Operation T urning the unit on T o turn the unit on, push the On/Off button up on the front panel. Pushing the On/Off button down turns the tuner off. Selecting the desired tuner From the fr ont panel, use to toggle between XM and AM/FM.
20 ST2-XM OPERA TION ST2-RC REMOTE CONTROL ST2-RC Remote Control Operation The ST2-RC remote contr ol is the only means of remote operation of the ST2-XM in a non--RNET sys- tem. The ST2-XM front panel displays information for the tuner that is receiving commands fr om the ST2- RC.
21 ST2-XM OPERA TION ST2-KP KEYP AD CONTROLS ST2-KP Keypad Operation T urning the keypad on/of f T o activate the ST2-KP , press . Pr ess to power down the keypad display . The keypad remains powered until the ST2-XM T uner is turned off. Selecting the desired tuner T o select a different tuner , press and hold .
22 ST2-XM OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 CAV6.6-UNO-S2 Keypad Operation NOTE: To control the ST2 Tuner through the UNO-S2 keypad, the tuner must be configured as a source using the CAV6.6 programming steps. T urning the unit on The tuner is power managed by the CAV6.
23 ST2-XM OPERA TION UNO-S2 KEYP AD CONTROLS WITH CAV6.6 TUNER SELECTION - Select source number assigned to TUNER 1 (XM) or TUNER 2 (AM/FM) TUNE UP/DOWN - Used for manual station or channel selection .
24 UNO-LRC1 Remote Control Operation T urning the unit on The tuner is power managed by the CAV6.6 or other RNET -enabled controller . If the tuner is in standby mode, any button press of the UNO-LRC1 will bring the tuner out of standby mode when used with the UNO keypad.
ST2-XM OPERA TION UNO-LRC1 REMOTE CONTROL WITH CA V6.6 POWER - Power managed by CAV6.6 NUMERIC INPUT - Number buttons for direct input of frequency , channel, preset, bank TUNE UP/DOWN - Incrementally.
26 ST2-XM T uner Setup Menus Note: The Setup Menu procedures must be performed from the ST2-XM Tuner front panel. The ST2-XM T uner Setup Menus provide setup and naming pr ocedures for the ST2-XM main chassis, the XM tuner module and the AM/FM tuner module.
27 ST2-XM TUNER PROGRAMMING ST2 TUNER SETUP MENU TNR SEL Press and Hold TNR SEL button ST2 Chassis Setup Proc edures TNR SEL TNR SEL This Procedure returns the ST2 T uner to its F actor y settings SOU.
28 System Info (Chassis) The System Info menu shows the ST2 T uner’ s manufacturing build properties. 1. Enter the Setup Menu by pressing and holding the TNR SEL button. 2. TUNER SETUP appears. Press MEM Up/Down until SYSTEM INFO appears on the tuner .
29 ST2-XM TUNER PROGRAMMING ST2 TUNER SETUP MENU Tuner Setup Menu for XM It is important to select the desired tuner (Tuner 1 for XM) using the TNR SEL button BEFORE accessing the Tuner Setup Menus. Memory Name (XM) A memory preset must be created and saved before it can be named (see page 19).
30 ST2-XM TUNER PROGRAMMING ST2 TUNER SETUP MENU Memory Name (XM) (continued) 9. Press BAND to advance. MEMOR Y NAME appears again. 10. Press BAND to access the Memory Name entry screen. 11. Press T une Up/Down to select a character and MEM Up/Down to change a character position.
31 ST2-XM TUNER PROGRAMMING ST2 TUNER SETUP MENU Press TNR SEL button to select XM T uner XM Setup Menu Con troller , Diagnostics, Factory Initialization and Sy stem Info Procedur es TNR SEL TNR SEL M.
32 ST2-XM TUNER PROGRAMMING ST2 TUNER SETUP MENU Memory Name (AM/FM) (continued) 1. Enter the Setup Menu by pressing and holding the TNR SEL button. 2. TUNER SETUP appears. Press BAND again. 3. MEMORY NAME appears on the tuner . 4. Press BAND. 5. Bank # appears.
33 AM/FM Setup Menu TNR SEL TNR SEL MEM NAME Procedure AM/FM Setup Menu TUNER SETUP Menu SOURCE NUM Procedure Chassis Setup Menu F ACT ORY INIT Procedure UPDA TE FIRMW Procedure SYSTEM INFO Procedure .
34 NOTE: The CAV6.6 firmware must be version 2.00.01 or higher and UNO-S2 firmware must be version 3.00.01 or higher to control the ST2-XM Tuner. Use the System Info Menu of the CAV6.6 to check the firmware version. If the firmware is not the proper revision as noted here, visit the Document Center at www.
35 ST2-XM Smart T uner Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm) Weight: 7 lbs. (3.2kg) Power Supply: 12VDC 1.5A Frequency Range: AM 530 - 1710 kHz FM 87.
36 WARRANTY & REP AIR The Russound ST2-XM is fully guaranteed against all defects in materials and workmanship for two (2) years from the date of pur chase. During this period, Russound will replace any defective parts and correct any defect in workmanship without char ge for either par ts or labor .
37 NOTES.
38 NOTES.
39 NOTES.
Russound 5 Forbes Road, Newmarket, NH 03857 tel 603.659.5170 • fax 603.659.5388 e-mail: tech@russound.com www .russound.com E. & O.E. Copyright © 2004 Russound ® All rights reserved.
An important point after buying a device Russound ST2-XM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Russound ST2-XM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Russound ST2-XM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Russound ST2-XM you will learn all the available features of the product, as well as information on its operation. The information that you get Russound ST2-XM will certainly help you make a decision on the purchase.
If you already are a holder of Russound ST2-XM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Russound ST2-XM.
However, one of the most important roles played by the user manual is to help in solving problems with Russound ST2-XM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Russound ST2-XM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
