Instruction/ maintenance manual of the product WIN7000 RuggedCom
Go to page of 34
RuggedMAX WiN7000 Installation Guide Revision 1 - March 9, 2011 www.RuggedCom.com.
RuggedMAX WiN7000 RuggedMAX WiN7000 : Installation Guide Copyright © 2010 RuggedCom Inc. All Rights Reserved Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted.
RuggedMAX WiN7000 RuggedCom® RuggedMAX WiN7000 3 Installation Guide Rev1 Table of Contents FCC Statement And Cautions ................................................................................................... 6 1. Introduction ..............
RuggedMAX WiN7000 RuggedCom® RuggedMAX WiN7000 4 Installation Guide Rev1 List of Figures 1.1. Typical Centralized DC Power System, Plant and Distribution Source-Grounded DC Power System ................................................................
RuggedMAX WiN7000 RuggedCom® RuggedMAX WiN7000 5 Installation Guide Rev1 List of Tables 3.1. WiN7000 Pole Mount Parts List ....................................................................................... 18 3.2. WiN7000 Wall Mount Parts List .
FCC Statement And Cautions RuggedCom® RuggedMAX WiN7000 6 Installation Guide Rev1 FCC Statement And Cautions Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules.
1. Introduction RuggedCom® RuggedMAX WiN7000 7 Installation Guide Rev1 1. Introduction The WiN7000 is a member of the RuggedMAX™ family, a line of mobile WiMAX broadband wireless access systems based on the 802.
1. Introduction RuggedCom® RuggedMAX WiN7000 8 Installation Guide Rev1 1.2. Capabilities and Features The WiN7000 provides the full base station functionality necessary for serving a single sector: • All-outdoor, single-box installation • IEEE802.
1. Introduction RuggedCom® RuggedMAX WiN7000 9 Installation Guide Rev1 1.3. Safety Information 1.3.1. General • Read this user manual and follow all operating and safety instructions. • The base station and antenna must be installed by a professional installer.
1. Introduction RuggedCom® RuggedMAX WiN7000 10 Installation Guide Rev1 Figure 1.1. Typical Centralized DC Power System, Plant and Distribution Source-Grounded DC Power System Figure 1.
1. Introduction RuggedCom® RuggedMAX WiN7000 11 Installation Guide Rev1 1.3.3. Equipment Installation Install the equipment in accordance with the electrical code relevant to the country of installation, such as the National Electrical Code (NEC), ANSI/NFPA 70; the Canadian Electrical Code (CEC), Part 1, CSA C22.
1. Introduction RuggedCom® RuggedMAX WiN7000 12 Installation Guide Rev1 1.3.8. Antenna Grounding Requirements The antenna installation must be as per Article 810 of the NEC. Of particular note is the requirement that the grounding conductor not be less than 10 AWG (Cu).
1. Introduction RuggedCom® RuggedMAX WiN7000 13 Installation Guide Rev1 1.4. WiN7000 Physical Specifications The WiN7000 outdoor base station is packed in a waterproof metal housing. A mounting bracket and mounting kit allows for pole or wall installation.
2. Site and Installation Requirements RuggedCom® RuggedMAX WiN7000 14 Installation Guide Rev1 2. Site and Installation Requirements 2.1. Mounting Considerations When choosing a mounting location, consider the available mounting structures and antenna clearance.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 15 Installation Guide Rev1 3. Installation Procedures 3.1. Pre-Installation Safety Instructions Installing the WiN7000 can pose a serious hazard.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 16 Installation Guide Rev1 3.4. Installing the WiN7000 The equipment should be installed in compliance with the National Electrical Code (NEC), ANSI/NFPA 70, the Canadian Electrical Code (CEC), Part 1, CSA C22.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 17 Installation Guide Rev1 3.4.1. WiN7000 Mounting Bracket The mounting bracket is used for both pole- and wall-mount installations.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 18 Installation Guide Rev1 3.4.2. Pole Mounting Figure 3.2. WiN7000 Pole Mounting Diagram Item Quantity Description 1 1 Mounting brackets 2 1 W.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 19 Installation Guide Rev1 3. Lift the base station by the eye bolts and secure it to the mounting bracket. At the top of the unit and mounting bracket, use NC 1/4" × 1/2" hex screws (Item 8) and NC 1/4" flat washers (Item 9).
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 20 Installation Guide Rev1 Procedure 3.2. Installing the WiN7000 on a Wall 1. Select a mounting location. 2. Place the mounting bracket on the wall and mark the location of the four mounting holes, two at the top and two at the bottom.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 21 Installation Guide Rev1 Figure 3.5. Copper Ethernet Port Option Number Connector Name Connector Type Cable Type Function Connected to 1 ANT1.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 22 Installation Guide Rev1 3.5. Weatherproofing It is extremely important to weatherproof all outdoor cable connections.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 23 Installation Guide Rev1 2. Tightly wrap the connector and the cable. Overlap the tape, without gaps, all the way along the connector. Continue wrapping the tape 25 mm (1") onto the cable.
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 24 Installation Guide Rev1 3.6. Power Connections 3.6.1. Copper and SFA Type Base Station The power system can be supplied by RuggedCom (WiNPS) or by the operator. Connect the power system DC + ETH output to the WiN cable proprietary connector (supplied by RuggedCom).
3. Installation Procedures RuggedCom® RuggedMAX WiN7000 25 Installation Guide Rev1 3.6.2. SFD Type Base Station The power system is supplied by the operator. Connect the power system DC output to the RuggedCom cable with proprietary connector (supplied by RuggedCom).
4. Setup RuggedCom® RuggedMAX WiN7000 26 Installation Guide Rev1 4. Setup The initial setup procedure consists of: • Configuring the computer’s network parameters and connecting the WiN7000 to the Web interface • Verifying IP connectivity 4.
4. Setup RuggedCom® RuggedMAX WiN7000 27 Installation Guide Rev1 Figure 4.2. Microsoft Windows Internet Protocol (TCP/IP) Properties dialog box 7. On the Internet Protocol (TCP/IP) Properties dialog, click OK . On the Local Area Connection Properties dialog, click Close .
5. Troubleshooting RuggedCom® RuggedMAX WiN7000 28 Installation Guide Rev1 5. Troubleshooting 5.1. No IP connectivity If there is no IP connectivity between the WiN7200 unit and the NMS, perform the following steps: 1. Connect the the computer and the WiN7200 Console connector (serial connection), located on the unit’s bottom panel.
Appendix A. Connector and Cable Pinouts RuggedCom® RuggedMAX WiN7000 29 Installation Guide Rev1 Appendix A. Connector and Cable Pinouts A.1. Power and Ethernet Cable Pinouts The pinout of the power cable is shown below: Figure A.
Appendix A. Connector and Cable Pinouts RuggedCom® RuggedMAX WiN7000 30 Installation Guide Rev1 A.2. Console Cable Pinouts In normal operation, the console connector should remain closed and should only be used by an authorized technician. The console connection is a 3-pin female connector, based on the RS-232 serial standard.
Appendix B. WiN7000 Specifications RuggedCom® RuggedMAX WiN7000 31 Installation Guide Rev1 Appendix B. WiN7000 Specifications Radio and Modem: • IEEE802.16-2005 (16e OFDMA) • WiMAX Forum Wave 2 Profile • Time Division Duplex (TDD) • Channel Bandwidth (MHz) 3.
Appendix B. WiN7000 Specifications RuggedCom® RuggedMAX WiN7000 32 Installation Guide Rev1 Environmental: • Operating Temperature: -40°C to +65°C • Operating Humidity 5% to 95% non condensing 1613 & IEC61850-3: EMC: • 1613 Section 6.3, 7, 8, 9 Class1 • IEC61850-3 Section 5.
Appendix C. List of Acronyms RuggedCom® RuggedMAX WiN7000 33 Installation Guide Rev1 Appendix C. List of Acronyms Acronym Description ASN Access Service Network BST Base Station IP Internet Protocol .
Appendix D. Warranty RuggedCom® RuggedMAX WiN7000 34 Installation Guide Rev1 Appendix D. Warranty RuggedCom warrants this product for a period of five (5) years from the date of purchase. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void.
An important point after buying a device RuggedCom WIN7000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RuggedCom WIN7000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RuggedCom WIN7000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RuggedCom WIN7000 you will learn all the available features of the product, as well as information on its operation. The information that you get RuggedCom WIN7000 will certainly help you make a decision on the purchase.
If you already are a holder of RuggedCom WIN7000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RuggedCom WIN7000.
However, one of the most important roles played by the user manual is to help in solving problems with RuggedCom WIN7000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RuggedCom WIN7000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
