Instruction/ maintenance manual of the product 300361 Rover
Go to page of 28
W arranty Conditions A ustrAliA & N ew Z eAlANd O Nl y F or y our record: Dealer’ s Name: ............................................................................................................. Dealer’ s Address: ........................
30” Q UEEN TM - SP ARE P ARTS LIST ITEM P ART No. DESCRIPTION 26 1 * A mower user must be in good physical condition and mental health and not under the influence of an y dr ug or alcohol which might impair vision, co-ordination or judgement. * Do not use a mow er when tired or f atigued.
25 2 MAINTENANCE AND ADJUSTMENT 30” QUEEN TM ELECTRIC MO WER 2 SPEED OPERA TION Normal Speed _ 4.9km/p.h 127 cuts per metre . Low Speed _ 3.2km/p.h 183 cuts per metre . SPEED CONTR OL T o change speed, stop motor and mov e r ibbed sliding slee ve (A) inwards to engage nor mal speed or outwards f or low speed as required.
3 24 HEIGHT ADJUSTMENT – T o cut lower , slack en quadrant clamp bolt nuts (1), also the lo wer adjusting screw nut (2). Then tighten top adjusting screw nut (3) until desired height of cut is obtained. T o cut higher , re verse procedure. Re-tighten all nuts after desired setting is obtained.
23 4 T O CHECK THE MO WER FOR ALIGNMENT – Y our mo wer is designed to produce the perf ectly flat cut that is required f or a top quality green. Ridging or stepping between cuts means that the heigh.
5 22 REVERSING CUTTER – A feature of this machine is that the cylinder ma y be easily remov ed, re versed end f or end and replaced. This provides a new k een cutting edge. If the bottom blade is badly worn, this should be replaced at the same time that the cutting cylinder is re versed or replaced.
21 6 LUBRICA TION – Pre-lubr icate, sealed ball races are fitted to the cutter , dr um shaft, countershaft and front roller . No fur ther lubrication is necessar y to these 8 races. Drums are fitted with special self-lubricating b ushes and do not require lubrication.
7 20 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305390 Handleassembly 2 305445 Cord carrier assembly 3 173024 Cord grip 4 163029 Cord grip ring 5 305496 Clutch c.
8 19 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305795 Sideframeassembly-LH 2 305779 Sideframeassembly-RH 3 302148 Clutch housing cov.
9 18 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305648 Deectorassembly 2 301065 Deectorstripassembly 3 305664 Scraper trough assembly 4.
17 10 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 301217 Drum shaft 2 303992 Drum outer assembly 3 304012 Drum inner assembly 4 301 188 Ratchetboxassembly 5 31 1 1255 Bush 6 301807 Drum shaft sleeve 7 301 196 Pawl retainer 8 333024 Drum pawls 9 301840 Drumshaftcollar-LH.
16 11 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION ITEM P ART No. DESCRIPTION 1 302869 Countershaft 2 301962 Countershaft sprocket 3 1502474 Circlip 4 1 122422 Countershaft bearing 5 301815 Countershaftbearinghousing-LH.
15 12 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 306122 Blade cutter assembly- 10 blades 1 10168 Blade cutter assembly- 16 blades 2 393000 Bottom blade- low cut 3 301735 Sole pl.
13 14 30” QUEEN TM - SP ARE P ARTS LIST ITEM P ART No. DESCRIPTION 1 301516 Front roller assembly 2 304506 Clamping channel 3 304514 Clamping tyne guide 4 166246 Rake tynes- 32 per set 5 304522 Clam.
13 14 30” QUEEN TM - SP ARE P ARTS LIST ITEM P ART No. DESCRIPTION 1 301516 Front roller assembly 2 304506 Clamping channel 3 304514 Clamping tyne guide 4 166246 Rake tynes- 32 per set 5 304522 Clam.
15 12 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 306122 Blade cutter assembly- 10 blades 1 10168 Blade cutter assembly- 16 blades 2 393000 Bottom blade- low cut 3 301735 Sole pl.
16 11 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION ITEM P ART No. DESCRIPTION 1 302869 Countershaft 2 301962 Countershaft sprocket 3 1502474 Circlip 4 1 122422 Countershaft bearing 5 301815 Countershaftbearinghousing-LH.
17 10 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 301217 Drum shaft 2 303992 Drum outer assembly 3 304012 Drum inner assembly 4 301 188 Ratchetboxassembly 5 31 1 1255 Bush 6 301807 Drum shaft sleeve 7 301 196 Pawl retainer 8 333024 Drum pawls 9 301840 Drumshaftcollar-LH.
9 18 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305648 Deectorassembly 2 301065 Deectorstripassembly 3 305664 Scraper trough assembly 4.
8 19 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305795 Sideframeassembly-LH 2 305779 Sideframeassembly-RH 3 302148 Clutch housing cov.
7 20 30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 1 305390 Handleassembly 2 305445 Cord carrier assembly 3 173024 Cord grip 4 163029 Cord grip ring 5 305496 Clutch c.
21 6 LUBRICA TION – Pre-lubr icate, sealed ball races are fitted to the cutter , dr um shaft, countershaft and front roller . No fur ther lubrication is necessar y to these 8 races. Drums are fitted with special self-lubricating b ushes and do not require lubrication.
5 22 REVERSING CUTTER – A feature of this machine is that the cylinder ma y be easily remov ed, re versed end f or end and replaced. This provides a new k een cutting edge. If the bottom blade is badly worn, this should be replaced at the same time that the cutting cylinder is re versed or replaced.
23 4 T O CHECK THE MO WER FOR ALIGNMENT – Y our mo wer is designed to produce the perf ectly flat cut that is required f or a top quality green. Ridging or stepping between cuts means that the heigh.
3 24 HEIGHT ADJUSTMENT – T o cut lower , slack en quadrant clamp bolt nuts (1), also the lo wer adjusting screw nut (2). Then tighten top adjusting screw nut (3) until desired height of cut is obtained. T o cut higher , re verse procedure. Re-tighten all nuts after desired setting is obtained.
25 2 MAINTENANCE AND ADJUSTMENT 30” QUEEN TM ELECTRIC MO WER 2 SPEED OPERA TION Normal Speed _ 4.9km/p.h 127 cuts per metre . Low Speed _ 3.2km/p.h 183 cuts per metre . SPEED CONTR OL T o change speed, stop motor and mo ve r ibbed sliding slee ve (A) inwards to engage nor mal speed or outwards f or low speed as required.
30” QUEEN TM - SP ARE P AR TS LIST ITEM P ART No. DESCRIPTION 26 1 * A mower user must be in good physical condition and mental health and not under the influence of an y dr ug or alcohol which might impair vision, co-ordination or judgement. * Do not use a mow er when tired or f atigued.
W arranty Conditions A ustrAliA & N ew Z eAlANd O Nl y F or y our record: Dealer’ s Name: ............................................................................................................. Dealer’ s Address: ........................
An important point after buying a device Rover 300361 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rover 300361 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rover 300361 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rover 300361 you will learn all the available features of the product, as well as information on its operation. The information that you get Rover 300361 will certainly help you make a decision on the purchase.
If you already are a holder of Rover 300361, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rover 300361.
However, one of the most important roles played by the user manual is to help in solving problems with Rover 300361. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rover 300361 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
