Instruction/ maintenance manual of the product K-9 Audiovox
Go to page of 10
Page 1 of 10 P/N 8007132 REV. B BJ ASA Electronics TV/VCP Floor Console Model K - 9 With out Harness and Antenna 12 Volt DC powered remote controlled 9” television AVT - 975 12 Volt DC powered remot.
P/N 8007132 Page 2 of 10 Rev. B This manual contains specific instructions on how to install this automotive TV/VCP floor console. Please read this manual thoroughly before install ing the console into the vehicle.
P/N 8007132 Page 3 of 10 Rev. B There are six (6) steps to install the K - 9 TV/VCP floor console: Step # 1 Remove face of the console Step # 2 Install brackets and the straps Step # 3 Install console.
P/N 8007132 Page 4 of 10 Rev. B Step #2 Install brackets and straps 1) Mount brackets using four screws. Do not use center hole. 2) Use soldering iron, if necessary, to melt holes in open st rap, as shown. 3) Use soldering iron, if necessary, to melt holes in closed strap, as shown.
P/N 8007132 Page 5 of 10 Rev. B 3) Pre - drill 1/8” pilot holes on bottom TV shelf for strap..
P/N 8007132 Page 6 of 10 Rev. B 1) Attach both straps and customer - su pplied harness, securing harness as needed..
P/N 8007132 Page 7 of 10 Rev. B Step #3 INSTALL CONSOLE TO FLOOR OF VEHICLE ⇒ BEFORE DRILLING ANY HOLES VERIFY THAT DRILL BIT WILL NOT ENTER INTO FRAME RAIL(S) OF VEHICLE, ELECTRICAL WIRES, FUEL LINES, BRAKE LINES, HOSES, EXHAUST SYSTEMS OR ANY OTHER ITEMS THAT WILL IMPAIR OPERATION OF VEHICLE.
P/N 8007132 Page 8 of 10 Rev. B STEP #4 INSTALL VCP INTO CONSOLE ⇒ Remove VCP from box. ⇒ Connect white RCA connector (customer supplied) from console wiring harness to white audio output jack of VCP. ⇒ Connect yellow RCA connector (customer supplied) from console wiring harness to yellow audio output jack of VCP.
P/N 8007132 Page 9 of 10 Rev. B STEP #5 INST ALL TV INTO CONSOLE ⇒ Connect yellow RCA connector (customer supplied) to yellow RCA input jack on rear of television. This is the video connection. ⇒ Connect white RCA connector (customer supplied) to white RCA input jack on rear of television.
P/N 8007132 Page 10 of 10 Rev. B STEP #6 REPLACE THE FACE OF THE CONSOLE ⇒ Place face of console over body of console. Gently tap into place. ⇒ Install four Phillips screws that hold the face to the body.
An important point after buying a device Audiovox K-9 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox K-9 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox K-9 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox K-9 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox K-9 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox K-9, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox K-9.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox K-9. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox K-9 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
