Instruction/ maintenance manual of the product RCX-Z4 Rosewill
Go to page of 13
user manual COOLER RCX-Z4.
1 user manual COOLER RCX-Z4 Improper Installation will result in damage to the processor . Never switch on the computer system until the fan is connected on to the motherboard power connector .
A X 5 B X 5 C X 1 Installation Components D X 2 E X 2 F X 1 G X 8 H X 2 I X 2 J X 4 K X 6 L X 1 M X 4 N X 4 O X 2 2 user manual COOLER RCX-Z4.
AMD K8 / AM2 Installation 1 Remove the retention module from the motherboar d by removing the scr ews. Keep the original motherboard backplate as it is. 2 NOTE The K8 / AM2 heatsink retention bracket have been pre-installed on the heatsink. Do not remove for K8 / AM2.
Stick the protective insulated film onto the back of the heatsink retention brackets. 3 4 O Apply the proper amount of thermal compound on the CPU surface, a thin film is ideal, extra thermal compound will not improve performance. Make sure the CPU surface is perfectly clean.
Place the RCX-Z4 on the top of the CPU, align two holes ( shown in red as the picture below ) of heatsink retention bracket with the Motherboard holes.
Remove the fan from the sink by unscrewing the four black screws. Take off the pre-attached pair of K8-AM2 heatsink retention bracket; keep the four screws for the next 6 user manual COOLER RCX-Z4 E INTEL P4 LGA775 Installation 1 2 Attach both of the LGA775 heatsink retention brackets to the heatsink base.
Place the screws through the backplate into the head thread of the screws , make sure the correct four holes are used, as shown in the diagram highlighted with red. Follow the same procedure for all four screws. 7 user manual COOLER RCX-Z4 Put the backplate with the screws fixed through the four motherboard holes as illustrated.
Secure the backplate onto the motherboard by using the four collars nuts . Turn these down onto the insulation washer, do not tighten one first, work around all four, gradually tightening them all. 8 user manual COOLER RCX-Z4 Put the four rubber pads on top of the four screws .
Place the cooler onto the four screws, secure the cooler with four more collars . 9 user manual COOLER RCX-Z4 Screw the fan onto the heatsink using the four black screws. Apply the proper amount of thermal compound on the CPU surface, a thin film is ideal, extra thermal compound will not improve performance.
Connect the fan cable with 3 pin connector to the Fan Controller Cable. 10 user manual COOLER RCX-Z4 Connect the 3-pin connector of the Y fan cable assigned with a yellow and a black cable to the CPU fan motherboard connector. Remove a PCI slot backplate and install the fan control unit.
Connect the power cable to the speed control and to the PSU 4-pin connector. 11 user manual COOLER RCX-Z4 Connect the 3-pin connector with the yellow / red / black cable to the Controller Circuit board.. 4 5 Thank you for purchasing a quality Rosewill Product.
www.rosewill.com.
An important point after buying a device Rosewill RCX-Z4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rosewill RCX-Z4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rosewill RCX-Z4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rosewill RCX-Z4 you will learn all the available features of the product, as well as information on its operation. The information that you get Rosewill RCX-Z4 will certainly help you make a decision on the purchase.
If you already are a holder of Rosewill RCX-Z4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rosewill RCX-Z4.
However, one of the most important roles played by the user manual is to help in solving problems with Rosewill RCX-Z4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rosewill RCX-Z4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
