Instruction/ maintenance manual of the product EASYN400 Rosewill
Go to page of 112
W ireless Router RNX-EasyN400 User Manual.
Wir eless Router RNX-Eas yN400 User M anual 1 Safety Warning • Place connecting cables carefu lly so that no one w ill step on th em or stumble over them. • Always disconnect all cables from this device before servicing or disassem bling. • Use ONLY an appropriate power adaptor or cord for your device.
Wir eless Router RNX-Eas yN400 User M anual 2 Table of Contents T AB LE OF CONTENTS ............................ ................................ ....................................... ........... .........2 BEFORE WE BEGIN ............. ............
Wir eless Router RNX-Eas yN400 User M anual 3 3.7.1 Advanced .......................................................................... ....................................... ................. 58 3.7.2 Dem ilitarized Zone (D MZ) .....................
Wir eless Router RNX-Eas yN400 User M anual 4 Before We Begin • Please configure RNX-EasyN400 with the comp uter that was last co nnected directly to your mo dem.
Wir eless Router RNX-Eas yN400 User M anual 5 1 Introduction 1.1 Over view Congratulations on y our purchase of RNX-EasyN40 0 Wireless Network Broadband Router.
Wir eless Router RNX-Eas yN400 User M anual 6 enhance security WDS (Wireless Distribution System) Make wireless AP an d Bridge mode simultaneously as a w ireless r epeater ** Theoretical wireless signal rate ba sed on IEEE standard o f 802.11a, b, g, n chipset used.
Wir eless Router RNX-Eas yN400 User M anual 7 1.4 Product La yout and LED S ignal LED Colo r St a t u s Description On RNX-EasyN400 is receiving power and functioning properly.
Wir eless Router RNX-Eas yN400 User M anual 8 Blinking RNX-EasyN400 i s sending/receiving data th rough WAN Off The W AN is not ready or fail On RNX-EasyN400 has a succe ssful Ethernet connec tion.
Wir eless Router RNX-Eas yN400 User M anual 9 1.7 RNX-EasyN400’s LAN & WAN Cable Connection Setup W A N co nnect ion: Connect Ethernet cable between W AN ports of your ADSL/CABLE modem & INTERNET port of RNX-EasyN400. Make su re your ADSL/CABLE modem is working well.
Wir eless Router RNX-Eas yN400 User M anual 10 RNX-EasyN400 LAN Connection Diagram.
Wir eless Router RNX-Eas yN400 User M anual 11 2 Setup Wizard We will introduce the Smart Wizard in this section. Please make sure the following before inser t the CD into the CD/DV D drive: • Internet connection should be setup & ready to use (ADSL or cable modem).
Wir eless Router RNX-Eas yN400 User M anual 12 Click User Manual to open user manual. Click Ad obe Reader to install Adobe Acrobat reader on your PC/Noteb ook. Click EX IT anytime you want to abort. 2.2 Setup Wizard – Configur atio n Click <Next> to proceed.
Wir eless Router RNX-Eas yN400 User M anual 13 Make sure your DSL/CABLE modem is setup and wo rking. Else take the help of y our internet service provider. Click <Next> to proceed. Check the MODEM and RNX-EasyN400 connection. It sho uld be as shown below.
Wir eless Router RNX-Eas yN400 User M anual 14 Notice the LED will light up at this stage. If not, check your procedures again. Click <Next> to configure WAN & Wireless setting s.
Wir eless Router RNX-Eas yN400 User M anual 15 Then, you will be prompt to RNX-EasyN400 login page User name and password are admin/adm in. C lick <OK> .
Wir eless Router RNX-Eas yN400 User M anual 16 Click <Next> to ente r mode sel ectio n. 2.3 Setup Wizard – Con nect Mo de Sel ection This is where you s elect t he mode that RNX-Eas y N400 is going t o be use and set it s configurations.
Wir eless Router RNX-Eas yN400 User M anual 17 Depending on your Network setting, Wizard will show you either one of the pages below, the best detecting option will be selected, please click < Next > unless you wa nt to manually configure yo ur connectin g op tion.
Wir eless Router RNX-Eas yN400 User M anual 18 LABEL DESCRIPTION Host Name This is optional. Depending on if your ISP require you to provide this information. Please leave this blank, if you are not sure. MAC address The default value when Click < Clone MAC Address > is set to the WAN ’s physical interface of the broadb and router.
Wir eless Router RNX-Eas yN400 User M anual 19 Please choose your security level, and enter your desired name for your wireless network ( SSID ) and security key ( Key ); Click < Next > to proceed. Depending on how y ou set up RNX-EasyN400, you will see different result pages before you reboot your RNX-EasyN400.
Wir eless Router RNX-Eas yN400 User M anual 20 Below is the example page, if you select the h i ghest security to be your RNX-EasyN4 00 Connecting option. To apply the entire configuration, c l ick < Reboot >. You wi ll see the below cou nt do wn whe n < Reboot > clicked.
Wir eless Router RNX-Eas yN400 User M anual 21 NOTE: After W ireless settings are applied, yo u need to connect fro m your WLAN client with the security settings you just finished configuring. Remember to write down the type of security & security key you selected.
Wir eless Router RNX-Eas yN400 User M anual 22 You should see the below page, click < Reboot > You will see the count down o f the sy stem rebooting 2.3.3 Connectin g to RNX-E a s yN400 in AP Repeater Mode RNX-EasyN400 will res tart as a repeater now.
Wir eless Router RNX-Eas yN400 User M anual 23 1. Click on Start > Control Panel > Network and Internet Con nections > Network connections. 2. Righ t-click on the Local Area Connection which represents your net work card and selects Properties.
Wir eless Router RNX-Eas yN400 User M anual 24 192.168.0.X where X is a number between 100 and 200. Make sure that the number you choose is not in use on the networ k. Set Subnet mask as 255.255.255.0. 5. Set Default Gateway the same as the LAN IP address of your router (192 .
Wir eless Router RNX-Eas yN400 User M anual 25 8. You will see the configuration homepage u nder “ REPEATER ” m ode now ..
Wir eless Router RNX-Eas yN400 User M anual 26 3 Accessing RNX-EasyN400 through Web Browser in Router Mode 1. Make sure your RNX-EasyN400 hardware is properly connected and prepare y our computer or computer network to connect to the RNX-EasyN400 (refer to the Qui ck St ar t Gu ide ) .
Wir eless Router RNX-Eas yN400 User M anual 27 3.1 Resetting the RNX-EasyN400 If you forget your password or IP address, or you cannot access the RNX-EasyN400 through Web Bro wser, you will need to us e the < RESET> button at the back of the RNX-EasyN400 to reload the factory-default configuration file.
Wir eless Router RNX-Eas yN400 User M anual 28 3.2.1 Naviga ting RNX-Easy N400 in AP Router Mode Click on the si de menu selection on System , The picture screen b elow shows the status screen in AP Router Mode .
Wir eless Router RNX-Eas yN400 User M anual 29 Status This page shows the current Internet connection typ e and status. Dynamic IP This page is only use when your ISP provides you with below information Static IP This page is when your ISP a ssigns you with a fix IP addr ess to connect.
Wir eless Router RNX-Eas yN400 User M anual 30 servers/clients in your LAN to handle different service/Internet appli cation type (e.g. Email, FTP, Web server etc.
Wir eless Router RNX-Eas yN400 User M anual 31 3.2.2.1 RNX-EasyN 400 Side M enu Desc ription Table – AP Repeater Mode LABEL DESCRIPTION Status This shows the RNX-EasyN400’s general device, system and interface status information. LAN This is where you can configure LAN IP ad dress, subnet mask, also to enable DHCP server and IP range.
Wir eless Router RNX-Eas yN400 User M anual 32 web-based management Time The Time Zone allows your router to reference or base its tim e on the settings.
Wir eless Router RNX-Eas yN400 User M anual 33 3.3 RNX-EasyN400’s System Page 3.3.1 Status This page allows you to monitor the current status of y our router. Syste m: You can see the Uptime, hardw are information, serial number as well as firmware version i nformation.
Wir eless Router RNX-Eas yN400 User M anual 34 3.3.2 LAN The LAN Tabs reveals LAN settings which can be altered at will. If you are an entry level user, try accessing a website from your b rowser. If you can access website without a glitch, just do not change any of these settings.
Wir eless Router RNX-Eas yN400 User M anual 35 DHCP Server DHCP Server: This can enable or disable the Dynamic Pool setting. Lease time: This is the lease time of each assigned IP address. Start IP: This is the beginning of the IP pool for DHCP client hosts.
Wir eless Router RNX-Eas yN400 User M anual 36.
Wir eless Router RNX-Eas yN400 User M anual 37 3.3.4 Schedu le This page allows users to set up schedule func tion fo r Firewa ll and Power Saving. Edit schedule op tions to allow con figuration of firewall and power savings services to take effect. Fill in the schedule and select type of service.
Wir eless Router RNX-Eas yN400 User M anual 38 3.3.5 L o g Vie w operation event log . This page shows the current system log of the Broadband router. It displays any event occurred after syst em start up.
Wir eless Router RNX-Eas yN400 User M anual 39 3.3.7 Langua ge This Wireless Router support multiple langu age, You can select your desired langu age here.
Wir eless Router RNX-Eas yN400 User M anual 40 3.4 RNX-EasyN400’s Wizard Page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click < Next >. The details please refer to Setup Wizard at < Page 10 >.
Wir eless Router RNX-Eas yN400 User M anual 41 3.5 RNX-EasyN400’s Internet Page 3.5.1 Status This pa ge shows the curr ent Inte rnet c onnecti on type an d statu s. 3.5.2 Dynamic IP Use the MAC address when registering for Internet service, and do not change it unless required by your ISP .
Wir eless Router RNX-Eas yN400 User M anual 42 Host Name: This is option al. Please enter only when your ISP pro vider provides you with this info r mation . MAC address: The default value is set to the WAN’s physical interface of the broadband router.
Wir eless Router RNX-Eas yN400 User M anual 43 Authentication type: Please use de fault < Auto > to aut o- detec t the best type. Type: Enable the Automatic Conn ection option to automatica lly re-establish the connection when an application atte mpts to access the Internet again.
Wir eless Router RNX-Eas yN400 User M anual 44 3.6 RNX-EasyN400’s Wireless Page 3.6.1 Basic In this wireless basic setting page, you can set your wireless con nection based on Radio, Mode, Band, SSID, and Channel. Radio: You can turn on/off wireless ra dio.
Wir eless Router RNX-Eas yN400 User M anual 45 2.4 GHz (B): If all of your clients are 802.11b, select this one. 2.4 GHz (N): If all of your c lients a re 802.11 n, selec t this one . 2.4 GHz (B+G): Either 802.11b or 802.11g wireless devices are in y our environment.
Wir eless Router RNX-Eas yN400 User M anual 46 Enable SSID: We support up to 4 m ultiple SSIDs in this devi ce. Ple ase sel ect how m any SSIDs you would like to use in your n etwo rk environmen t. SSID1~4: ESSID is the name of your wireless network .
Wir eless Router RNX-Eas yN400 User M anual 47 3.6.2 WDS with AP Router WDS (Wireless Distribution System), a system that enables the wireless in tercon nection of access point, allows a wireless network to be exten d ed using multiple APs without a wired backbone to link them.
Wir eless Router RNX-Eas yN400 User M anual 48 3.6.3 Advan ce d Advanced function allows you to set your RN X-EasyN400 in adv anced wire less options. You should not cha nge these parameters un less you know w hat effect the changes will have on RNX-EasyN400.
Wir eless Router RNX-Eas yN400 User M anual 49 Data Rate: The “Data Rate” is the ra te that th is access point uses to trans mit data packets. The access point w ill use the highest possible selected tran smission rate to transmit the data packets.
Wir eless Router RNX-Eas yN400 User M anual 50 SSID Selection: This broadband router support multiple SSID, you could sele ct and set up the wanted SSID. Broadcast SSID: If you enabled “ Broadcast SSID ”, every wireless station located within the cov erage of the RNX-EasyN400 can discover its signal easily.
Wir eless Router RNX-Eas yN400 User M anual 51 WEP Encryption When you select 64-bit or 128-bit WEP key, you have to enter WEP key s to encrypt data. You can generate the key by yourself an d enter it. You can enter four WEP key s and select one of them as a default key.
Wir eless Router RNX-Eas yN400 User M anual 52 Authentication Ty pe: There are two authentication typ es: "Open System" and "Shared Key" . Both AP and wireless client must be configured with the same authentication ty p e. Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit.
Wir eless Router RNX-Eas yN400 User M anual 53 WPA-Radius Encryption Wi-Fi Protected Access ( WPA ) is an advanced security standard. You can use an external RADIUS server to authen ticate wireless stations and provide the session key to encrypt data during communication.
Wir eless Router RNX-Eas yN400 User M anual 54 Enable wireless access control: Enable the wireless access control function . Adding an address into the list Enter the "MAC Address" and "Description" of the wireless station to be added and then click < Add >.
Wir eless Router RNX-Eas yN400 User M anual 55 3.6.6 WPS (Wi-Fi Protected Setup) WPS is the simplest way to establish a connection between the wireless clients and the wireless router. You don’t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection.
Wir eless Router RNX-Eas yN400 User M anual 56 information when connecting to other WPS-enab led wireless devices. SSID : This is t h e network br oadcas t name (S SID) of R NX-EasyN400. Authentication Mode: It shows the active authentication mode for the wireless connection.
Wir eless Router RNX-Eas yN400 User M anual 57 Communication betw e en Wireless clients: A llow Wirele ss Client to co mmunicate wi th other W ireless C lient on s pecifi c SSID. Communication between Wireless clients an d wired clients: Allow Wir eless Client t o communicate with Wired Client on the switch on specific SSID.
Wir eless Router RNX-Eas yN400 User M anual 58 3.7 RNX-EasyN400’s Firewall Pa ge The Broadband router provides ex tensive firewall protection by restricting con nection parameters, thus limiting the risk of hacker attacks, and defending against a wide array of common Internet attacks.
Wir eless Router RNX-Eas yN400 User M anual 59 server re-directs a particular serv ice/Internet application (e.g. FTP, websites) to a particular LAN client/serv er, whereas DMZ re-directs all packets (regardless of servic es) from your WAN IP address to a particular LAN client/server.
Wir eless Router RNX-Eas yN400 User M anual 60 Disc ard Pi ng From W AN: RNX-EasyN400’s WAN port will not respond to any Ping requests Port Scan: Protects RNX-EasyN40 0 from Port Scans.
Wir eless Router RNX-Eas yN400 User M anual 61 Fill in “ LAN MAC Address ” and <Description> of the PC that is allowed / denied to access the Internet, and then click <Add> . If you find any typo before adding it and want to retype again, just click <Reset> and the fields will be cleared.
Wir eless Router RNX-Eas yN400 User M anual 62 Deny: If you select “ Deny ” then al l clients will be allowed to access Internet except for the clients in the list below. All ow: If you select “ Allow ” then all clients will be denied to access Internet except for the PC s in the lis t be low.
Wir eless Router RNX-Eas yN400 User M anual 63 Fill in “URL/Keyword” and then click <Add> . You can enter the full URL address or the keyword of the web site you want to block. If you happen to make a mistake and want to retype aga in, just click "Res et " and the fie l d will be cleared.
Wir eless Router RNX-Eas yN400 User M anual 64 3.8 RNX-EasyN400’s Advanced Page 3.8.1 Network Address Tr anslation (NAT) Network Address Translation (NAT) allows mul tiple users at yo ur local site to access the Internet through a single Public IP Address or multiple Public IP Addresses.
Wir eless Router RNX-Eas yN400 User M anual 65 Enable Port Mapping: Enable or disable port mapping function. Description: description of this se tting. Local IP: This is the local IP of the server behind the NAT firewall. Protocol: This is the prot ocol t ype to be forwarde d.
Wir eless Router RNX-Eas yN400 User M anual 66 D<D elete S elect ed> . I f you want to remove all Port Mapp ing settings from the table, click <Delete All> button. C lick <Reset> wil l clear your current sele ction s. Click < Apply > at the bottom of the screen to save the above configurations.
Wir eless Router RNX-Eas yN400 User M anual 67 Protocol: Select the port number protocol ty pe (TCP, UDP or both). If you are unsu re, then leave it to the default “both” setting.
Wir eless Router RNX-Eas yN400 User M anual 68 Enable Trigger Port: Enable or disable the Port Trigger function. Trigger Port: This is the outgoing (Outbound) range of port numbers for this particular application. Trigger Type: Select whether the out bound por t prot ocol is “ TCP ”, “ UDP ” or “ BOTH ”.
Wir eless Router RNX-Eas yN400 User M anual 69 Add Port Triggering Fill in t he " Trigger Port ", " Trigger Type ”, “ Public Port ”, " Public Type ", " Pu blic Port " and " Descripti on " of the setting to be added and then Click <Add> .
Wir eless Router RNX-Eas yN400 User M anual 70 3.8.6 UPnP With UPnP, all PCs in you Intranet will discover this router automatically. So, you don’t have to configure your PC and it can easily access the Internet throu gh this router. Enable/Disable UPnP: You can enable or D isable the UPnP feature here.
Wir eless Router RNX-Eas yN400 User M anual 71 This can put the p ackets of specific proto cols in High/Low Qu eue. The packets in High Queue will process first.
Wir eless Router RNX-Eas yN400 User M anual 72 This can reserve / limit the thro ughput of specific protocols and port range. Y ou can set the upper bound and Lower bound . T ype: Spec ify the direction of packets. Upload, d own load or both . IP range: Sp ecify the IP address ran ge.
Wir eless Router RNX-Eas yN400 User M anual 73 Desti nation LAN IP : Specify the destination LAN IP address of static routing rule. Subnet Mask: Specify the Subnet Mask of static routing rule. Default Gateway: Specify the defau lt gateway of static routing rule.
Wir eless Router RNX-Eas yN400 User M anual 74 You can change the password required to log into the broadband router's system web- based management. By default, the password is: admin. Passwords can co ntain 0 to 12 alphanumeric characters, and are case sensitive.
Wir eless Router RNX-Eas yN400 User M anual 75 Host Address: This is the IP address of the host in the In ternet that will have management/con figu ration access to the Broad band router from a remote site.
Wir eless Router RNX-Eas yN400 User M anual 76 Time Z one: Select the time zone o f the country you are curren tly in. RNX-EasyN4 00 will set its time based on your sele ction. NTP T ime Serve r: RNX-Eas yN400 can set up external NTP Time Server. Daylight Savings: RNX-EasyN400 can also take Daylight Savings into a ccount.
Wir eless Router RNX-Eas yN400 User M anual 77 3.9.3 DDNS DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain name f rom the DDNS service providers. This router supports DynDNS , TZO and other co mmon DDNS service providers.
Wir eless Router RNX-Eas yN400 User M anual 78 3.9.5 Diagn osis This page could let you diagnosis y our current network status. B y entering any website address, you will know if the internet connection is connected. 3.9.6 Firm ware This page allows you to upgrad e RNX-EasyN400’s firmware.
Wir eless Router RNX-Eas yN400 User M anual 79 Once you’ve selected the n ew firmware file, cl ick < A pply > at the bottom of the screen to start the upgrade process Caution: • T o upgrade firmware, please make sure the wireless connection is disabled and the computer is connected with a cabl e to the router .
Wir eless Router RNX-Eas yN400 User M anual 80 S tep 2 Log on to the manag ement web page of the AP . By default, the management IP is http://192.168.0.1 , and the user name is “admin”; password is “admin” . Step 3 Click < To ols > and < Firmware >, then Clic k < Browse >.
Wir eless Router RNX-Eas yN400 User M anual 81 Step 5 Click < Apply > button. Step 6 Click < OK > button for wr i ting the la test fir mware to your r outer . Step 7 Click < OK > button. 3.9.7 B ac k- up This page allows y ou to save the current rou ter configurations.
Wir eless Router RNX-Eas yN400 User M anual 82.
Wir eless Router RNX-Eas yN400 User M anual 83 4 Repeater Mode Repeater mode has limited se tting s compared to the AP mode. Choose “ Repeater mode ” on the top right corner of the configuration page. System will counting down and restarts automatically.
Wir eless Router RNX-Eas yN400 User M anual 84 2. Right-click on the Local A rea Connection which represents your network card and selects Properties. 3. High light Internet Protocol (TCP/IP) and click Properties . 4. Click to use the B section like below page.
Wir eless Router RNX-Eas yN400 User M anual 85 5. Set Default Gateway the same as the LAN IP address of your router (192.168.0.1). 6. Afte r finish, Click < OK >, Then < OK> on below page 7. Open your web browser and type in 192.168.0.1 on the address bar.
Wir eless Router RNX-Eas yN400 User M anual 86 8. You will see the configuration homepage un der “ Repeater mode ” now. Note: After finishing co figurate y our RNX-Eas yN400 in Repeater mode, please do remember to adjust your computer’s IP address function back to DHCP function.
Wir eless Router RNX-Eas yN400 User M anual 87 4.1 RNX-EasyN400 in Re peater Mode’s System page 4.1.1 Status This page allows you to monitor the current status of y our RNX-EasyN400 in Repeater mode. Syste m: You can see the Uptime, hardw are information, serial number as well as firmware version i nformation.
Wir eless Router RNX-Eas yN400 User M anual 88 The LAN Tabs reveals LAN setting s which can be altered at will. If y ou are an entry level user, try accessing a w ebsite fro m your browser. If you can access website withou t a glitch, just do not change any of these settings.
Wir eless Router RNX-Eas yN400 User M anual 89 The schedule table lists the pre-schedule service-runs. You c an select any of them using the check box. 4.1.4 L og View operation log of RNX-EasyN40 0 . This page shows the current system log of the Broadband router.
Wir eless Router RNX-Eas yN400 User M anual 90 4.1.5 Monitor Show the network packets histogram for network connection on WAN, LAN & WLAN. Auto refresh keeps information updated frequen tly . 4.1.6 Langua ge This Wireless Router support m ultiple language of web pages, you could select your nativ e lang uage here.
Wir eless Router RNX-Eas yN400 User M anual 91.
Wir eless Router RNX-Eas yN400 User M anual 92 4.2 RNX-EasyN400 in Repeat er Mode’s Wizard page Click Wizard to configure the Broadband Router. Setup wizard will be displayed; check that the modem is connected and click < Next >. The details please refer to Setup Wizard at < Page 10 >.
Wir eless Router RNX-Eas yN400 User M anual 93 You will see that when add SSID # 2 and SSID #3, you have “Security” in option to set up for your SSID #2 and S SID #3. Radio: This is where you set your RNX-EasyN 400 to broadcast the signal from your wireless router.
Wir eless Router RNX-Eas yN400 User M anual 94 Mode: This is predefined as Repe ater. Band: Depending on the wireless router yo u want to connect to, you will n eed to adjust the band accordingly to the wireless router. Enable SSID #: By default, RNX-EasyN400 h as 1 set of SSID in Repeater mode .
Wir eless Router RNX-Eas yN400 User M anual 95 Once selected your desired SSID connection, Click < Connect >, then you will see below page popup. Depending on the wireless signal that you want to connect to, RNX-EasyN400 will automatically configures to the current Encryption based on WEP, WPA and WPA2.
Wir eless Router RNX-Eas yN400 User M anual 96 All you have to do is to enter the password of the wireless router you want to co nnect with. Then Click < Apply > You will see the RNX-EasyN400 st.
Wir eless Router RNX-Eas yN400 User M anual 97 5 PC Network Adapter setup ( Under Windows XP ) • Enter [Start Menu] Æ select [Control panel] Æ select [Network].
Wir eless Router RNX-Eas yN400 User M anual 98 • Select [Internet Protocol (T CP /IP)] =>Click [Properties]. • Select the [General] tab and Click “a” on both selections. a. RNX-EasyN400 supports [ DHCP ] fu nction, p lease select both [ Obtain an IP address automatically ] and [ Obtain DNS server address automatica lly ].
Wir eless Router RNX-Eas yN400 User M anual 99.
Wir eless Router RNX-Eas yN400 User M anual 100 Appendix A – Product Specification Hardware Feature Dimensions 125mm (L) x 98mm (W) x 25mm (H) W AN: One 10/100 Fast E thernet RJ-45 LAN: Four 10/100 .
Wir eless Router RNX-Eas yN400 User M anual 101.
Wir eless Router RNX-Eas yN400 User M anual 102 Appendix B – Troubleshooting Q: How do I configue to set up Remote M anagement? A: Depending on your internet connect plans, your methods of setting up re mote mana gement wi ll be diff erent . 1. After Login to the RNX-EasyN400 management page, Click 「 Tools 」 , then 「 Admi n 」 .
Wir eless Router RNX-Eas yN400 User M anual 103 5. Aft er RNX-Ea syN400 fin ish re set, pl ease Cl ick “ System ”, the n from “ Status ” page below you wi ll see unde r “ WAN Settings ” which shows your External IP address (where has been red circled under “ WAN Settings ”).
Wir eless Router RNX-Eas yN400 User M anual 104 7. We suggest that you change the default login name and password to your desired login name and password which are difficult for others to guess or hack. (Rosewill default login/Password is admin) 8. Use above picture as an example.
Wir eless Router RNX-Eas yN400 User M anual 105 Q: What is the IP address of my RNX-E asyN400 ? A: The default IP address is 192 .168.0 . 1. However If you changed the IP address and have forgotten it, you might get the IP address of RNX-Easy N400 by lookin g up the IP ad dress of the default ga teway for your computer .
Wir eless Router RNX-Eas yN400 User M anual 106 • If you changed the IP address and have forgott en it, see the troubleshoo ting on how to find the IP address of your RNX-EasyN400. • Make sure your Internet br owser does not block pop -up window s and has JavaScrip ts and Java enabled.
Wir eless Router RNX-Eas yN400 User M anual 107 with a battery for when power is lost, i.e. T i me W arner Cable Modems, will keep the modem on and connected. Due to the ADSL/Cable modem not assign ing the c orrect DHCP inform ation, t he Rosewill Routers ca n not work correctly and assign a DH CP to the client computers.
Wir eless Router RNX-Eas yN400 User M anual 108 that might be in terfering with the wireless ne twork (for example, microwaves, other wirele ss networ ks, and s o on). • Reboot the RNX-Eas yN400. • Please update the Wi reless Adapter ’ s Firmware of yo ur Notebook and PC to the latest version to ensure the best connection.
Wir eless Router RNX-Eas yN400 User M anual 109 Appendix C – FCC Interference Statement Federal Communication Com mission Interfer ence S tatement This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursu ant to Part 15 of the F CC Rules.
Wir eless Router RNX-Eas yN400 User M anual 11 0 Italian: In alcuni Paesi si applicano i requisiti per il funzionam e nto in interni -esterni, i requisiti di lic enza e i ca nali consentiti, come desc.
Wir eless Router RNX-Eas yN400 User M anual 111 Appendix D – IC Interference Statement Industry Canada statement: This device complies with RSS-210 of the Industry Cana da Rules.
An important point after buying a device Rosewill EASYN400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rosewill EASYN400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rosewill EASYN400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rosewill EASYN400 you will learn all the available features of the product, as well as information on its operation. The information that you get Rosewill EASYN400 will certainly help you make a decision on the purchase.
If you already are a holder of Rosewill EASYN400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rosewill EASYN400.
However, one of the most important roles played by the user manual is to help in solving problems with Rosewill EASYN400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rosewill EASYN400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
