Instruction/ maintenance manual of the product VH-12 Roland
Go to page of 12
03458434 ’05-10-6N Owner’s Manual The VH-12 V-Hi-Hat is to be used in combination with the Roland TD-20 or TD-12 Percussion Sound Module. fig.Structure * Hi-hat stand is not included. For details on compatible stands, refer to p. 10. 202 Copyright © 2004 ROLAND CORPORATION All rights reserved.
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002a • Do not open or perform any internal modifications on the unit.
3 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes.
4 Getting Started Similar Touch and Feel as with an Acoustic Hi-Hat The superior design has taken into account not only the shape of the hi-hat, but also the bounce of the stick, and even the movement caused by playing, making it possible to play with the same feel as an acoustic hi-hat.
5 Mounting on the Hi-Hat Stand * Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-12. Be sure to use the special VH-12 clutch. fig.Clutch.e 1. Use the tuning key included with the VH-12 to loosen the clutch bolt, then simultaneously turn and remove the clutch top.
6 Mounting on the Hi-Hat Stand 1. Remove the clutch included with the hi-hat stand from the cymbal rod. * The clutch included with the hi-hat stand will not be used. * It is not necessary to remove the felt (or rubber) pad on the hi- hat stand used for supporting the bottom cymbal.
7 Mounting on the Hi-Hat Stand 6. Attach the clamp and holder to the pipe on the upper part of the hi-hat stand, then slightly tighten the assembly with the tuning key.
8 Mounting on the Hi-Hat Stand 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
9 Mounting on the Hi-Hat Stand 1. Adjust the gap between the top hi-hat and bottom hi-hat to a clearance of approximately 10 mm, then tighten the clutch screw.
10 Playing Methods The hi-hat tone changes smoothly and continuously from open to closed in response to how far the pedal is pressed. You can also play the foot closed sound (playing the hi-hat with the pedal completely pressed down) and foot splash sound (playing the hi-hat with the pedal fully pressed and then instantly opening it).
11 Troubleshooting Was the unit adjusted after being connected to the sound module? When using the VH-12, be sure to run the automatic offset adjustment on your sound module (p.
As of August 1, 2005 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.
An important point after buying a device Roland VH-12 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Roland VH-12 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Roland VH-12 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Roland VH-12 you will learn all the available features of the product, as well as information on its operation. The information that you get Roland VH-12 will certainly help you make a decision on the purchase.
If you already are a holder of Roland VH-12, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Roland VH-12.
However, one of the most important roles played by the user manual is to help in solving problems with Roland VH-12. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Roland VH-12 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
