Instruction/ maintenance manual of the product TD-6V Roland
Go to page of 148
03458934 5RCC To resize thickness, move all items on the front cover to left or right (6.54 mm) * All product names mentioned in this document are trademarks or registered trademarks of their respective owners. 202 Copyright © 2003 ROLAND CORPORATION All rights reserved.
To resize thickness, move all items on the front cover to left or right IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
3 010 • This unit, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable.
4 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2–3, please read and observe the following: Power Supply 301 • Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or variable lighting system).
5 Additional Precautions 551 • Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit.
6 Contents IMPORTANT NOTES ..................................................................................4 Contents .....................................................................................................6 Features ...................
7 Contents Quick Start ..................................................... 39 Choosing a Drum Kit ...............................................................................40 Playing While Listening to the Metronome/Click ......................
8 Contents Ambience Settings ................................................................ (AMBIENCE) ......................... 60 Switching Ambience On/Off ......................................... (Ambience Switch) .................. 60 Ambience “Send” Level for Each Instrument .
9 Contents Chapter 3 Global Settings for the TD-6V ........... (SETUP/UTILITY, Factory Reset) .........76 Making the Global Settings ................................................... (UTILITY) .............................. 76 Display Contrast Adjustment .
10 Contents Chapter 6 Recording a Song ................................... (Realtime Recording) ..92 Preparations for Recording ................................................................................................... 92 When Recording Pad Performances .
11 Contents Appendices .................................................. 109 Troubleshooting ....................................................................................110 No Sound ............................................................
12 Features Full Palette of Internal Sounds for All Uses, from Practice to Live Performance ■ Includes 99 Different Drum Kits You can immediately start playing any of a variety of drum kits, just by selecting the drum kit. Whether for practice or live performances, these kits can be applied in a wide range of situations.
13 Features Function and Operations Perfect for Live Performances ■ Flat Top Design for Great Visibility ■ Buttons Light for Easy Operation, Even On Stage ■ Large [+] and [-] Buttons That Can Be Operated Even with Drum Sticks Convenient Functions for Practicing ■ Includes Metronome (Click) (p.
14 How to Use This Manual Composition of This Manual This owner’s manual is organized as follows. Setup Guide (p. 15) For those using the TD-6V for the first time, this volume explains the preparations needed for playing sounds, including how to set up the stand, make pad settings, and turn on the TD-6V’s power.
15 Setup Guide Setup Guide TD-6KV_e.book 15 ページ ２００５年１月２４日 月曜日 午後７時４分.
16 Panel Descriptions Front Panel fig.P-022 Display The screen displays information, indicating the drum kit name, song name, and settings etc. VOLUME Knob Adjusts the volume of the TD-6V (p. 24). Even when headphones are connected, sound will still be output from the various output jacks.
17 Panel Descriptions Setup Guide SONG Button Calls up the song’s basic settings screen (p. 82). KIT Button Calls up the drum kit’s basic settings screen (p. 55). SHIFT Button Used in conjunction with other buttons. Editing section • EXIT Button Returns to the previous stage screen.
18 Panel Descriptions Rear Panel fig.P-023 POWER Switch Switch turns the power on/off (p. 23). Cord Hook Anchor the power cord (p. 22). AC Adaptor Jack Connect the supplied AC adaptor to this jack (p. 22). OUTPUT Jacks (L (MONO), R) Connect these to your amp or audio system.
19 Setup Guide Making the Settings Mounting the TD-6V to the Stand 1 Attach the stand holder (included with the optional drum stand) to the TD-6V. Using the screws attached to the bottom panel, attach the holder so the unit is oriented as shown in the diagram.
20 Making the Settings Connecting the Pads and the Pedals Using the provided cables, connect the pads, cymbal pads, hi-hat control pedal, and kick trigger unit. Carefully refer to the numbers shown in the illustration and connect to the appropriate TRIGGER INPUT jacks on the TD-6V's rear panel.
21 Making the Settings Setup Guide ■ Connecting Two Pads to Trigger Inputs 5/6 (TOM2/AUX) and 7/8 (TOM3/4) With the optional cable (PCS-31) or standard insert cable, two pads may be connected to the trigger inputs 5/6 (TOM2/AUX) and 7/8 (TOM3/4). For instructions on making these settings, refer to p.
22 Making the Settings Connecting Headphones, Audio Equipment, Amps, and Other Gear fig.P-010 1 Turn off the power of all devices before you make connections. 921 To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.
23 Setup Guide Turning On/Off the Power 941 Once the connections have been completed ( p. 22), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
24 Turning On/Off the Power 4 Turn on the power to the connected amp or audio system. 5 Press [SHIFT] + [KIT] (PREVIEW) or strike the pad, and while listening to the sound, gradually bring up [VOLUME] to adjust the volume level. Also raise the volume level of the connected amp or audio system to the appropriate level.
25 Setup Guide Restoring the Factory Settings ( Factory Reset) This restores the pad and instrument settings, song data, and other information stored in the TD-6V to the original factory settings. fig.P-003 1 While holding down [SHIFT], press [EDIT (SETUP)].
26 Restoring the Factory Settings (Factory Reset) 4 Press [+] or [-] to select the parameter you want to restore to factory settings. Here, select “ALL” to restore all of the settings to the original factory values. ALL: All internal settings will be restored to the factory settings.
27 Setup Guide Listening to the Demo Songs The TD-6V features five demo songs demonstrating the TD-6V’s sounds and expressive capabilities. The drums played on the demo songs were played in real time into a sequencer. fig.P-029 1 While holding down [KIT], press [SONG].
28 Listening to the Demo Songs 2 Press [+] or [-], or press [ ] or [ ] to select the song to play back. 1. How Now Copyright © 2003, Roland Corporation Drum kit being used: #11 “PopKit X” 2. TC R&B Copyright © 2001, Roland Corporation Drum kit being used: #80 “AcuStick” 3.
29 Setup Guide Selecting the Pad Type Make the settings for the type of pads to be used ( trigger type ) to ensure that the TD-6V accurately receives what is being played on the pads. Set each trigger input as described below. Settings optimized for the TD-6K are provided in factory settings on the TD-6V.
30 Selecting the Pad Type 4 Strike the pad you wish to set. The setting screen for the struck pad appears. 5 Select the most suitable trigger type from the following chart for the pad you are using. 6 Press [+] or [-] to select the trigger type. 7 Repeat Steps 4 – 6 to set the trigger type for each pad.
31 Setup Guide Adjusting the Sensitivity of the Pad You may wish to adjust the sensitivity of the pads to accommodate your personal taste and style of performing. Adjusting the TD-6V’s sensitivity allows you to change the correlation between your playing velocity (strength) and the response and volume of the sound.
32 Adjusting the Sensitivity of the Pad 4 Press [ ] to select “Sensitivity.” fig.P-020_50 5 Strike the pad you wish to set. The setting screen for the struck pad appears. 6 Press [+] or [-] to adjust the sensitivity of the pads. Here you can make a setting of 1–16.
33 Setup Guide About the Pads Trigger Inputs and the Pads You Can Use Although you can use previous model pads, kick trigger units, and other such devices with the TD-6V, there may be incompatibilities between pads and trigger inputs, which may prevent you from being able to perform on some pads.
34 About the Pads ■ Combinations of Pad and Trigger Type To enjoy full use of all the functionality offered by the TD-6V and your pads, be sure to review the following chart and select the pads best suited for your aims. fig.P-024a.e O : Can be used.
35 About the Pads Setup Guide ■ Recommended Parameters for the Pads The trigger parameters (except the Xtalk Cancel) are automatically set to the most efficient values for each pad when you select the trigger type.
36 About the Pads Playing the Pads ■ Pad Head Shots and Rim Shots When you perform a head shot, the head instrument is played; rim shots produce the sound of the rim instrument. To play a rim shot, you must strike both the head and the rim of the pad simultaneously .
37 About the Pads Setup Guide ■ Cymbal Bow Shots/Edge Shots/Bell Shots When you perform a bow shot, the head instrument is played; edge shots and bell shots produce the sound of the rim instrument. CY-6, CY-12H, CY-14C: Capable of bow shots and edge shots.
38 About the Pads ■ Cymbal Choke By striking a pad and then squeezing the rim portion of the pad, you can mute the note while the note is still sounding.
39 Quick Start Quick Start TD-6KV_e.book 39 ページ ２００５年１月２４日 月曜日 午後７時４分.
40 Choosing a Drum Kit The TD-6V comes with 99 preset drum kits. Now’s probably a good time for you to try out the drum kits by selecting and playing them. fig.Q-001 1 Press [KIT]. [KIT] lights, and the “DRUM KIT” screen appears. fig.Q-002ai 2 Press [+] or [-] to select the drum kit.
41 Quick Start Playing While Listening to the Metronome/Click Switching the Click On and Off Try using metronome (click). You can switch the click sound on and off by pressing [CLICK]. [CLICK] lights when set to play the sound. fig.Q-003.e fig.Q-004a 1 Press [CLICK].
42 Playing While Listening to the Metronome/Click Adjusting the Click Volume (Level) fig.Q-004 1 Confirm that [EDIT] is not lit. If [EDIT] lights, you can press [KIT] or [SONG] to turn it off. fig.Q-005 2 Press [CLICK]. [CLICK] lights, and the click sound begins to play.
43 Playing While Listening to the Metronome/Click Quick Start Adjusting the Click Tempo fig.Q-008 1 Press [CLICK]. [CLICK] lights, and the click sound begins to play. fig.Q-006 2 While holding down [SHIFT], press [CLICK (TEMPO)]. The Tempo screen appears.
44 Playing Along with Songs Choosing a Song and Playing Back The TD-6V features a sequencer that can record and play back accompaniment tracks and drum performances. This sequencer comes loaded with 170 Preset (internal) songs. fig.Q-010 ■ Choosing a Song 1 Press [SONG].
45 Playing Along with Songs Quick Start ■ Playing Back a Song 3 Press the [PLAY ] button, and the song will begin playing. [PLAY ] lights. fig.Q-012 4 To stop playback of the song, press [STOP ]. The [PLAY ] light goes out. fig.Q-013 When playback of a song is stopped, you can do the following.
46 Playing Along with Songs Adjusting the Song Volume You can adjust the song volume to correct the drum kit volume balance. Song volume consists of the two following adjustments. Backing Volume: Adjusts the volume of melodic instruments etc. other than percussion.
47 Playing Along with Songs Quick Start 4 Press [+] or [-] to select the volume. 5 When you finish making settings, press [SONG] to end the procedure. Temporarily Changing the Tempo of a Song You can temporarily change the tempo of a song while playback is in progress.
48 Playing Along with Songs Muting the Pre-programmed Drums in Songs You can mute just the drums recorded in a song. So you can play along. Try this using Song #8, “FUNK ROK.” fig.Q-019 1 Press [SONG]. [SONG] lights, and the SONG screen appears. fig.
49 Playing Along with Songs Quick Start 3 Press the [PLAY ] button, and the song will begin playing. [PLAY ] lights. fig.Q-022 4 Press [PART MUTE]. [PART MUTE] lights, and the drum sound are muted. fig.Q-023 5 To hear the drums, press [PART MUTE] once more.
50 Using the Pads to Play Songs The pads can also be set so that they start the performance of songs when struck ( Pad Pattern function ). This function is available only with electronic drums. The Pad Pattern function is already selected in Drum Kit #8, “1ManBand+.
51 Quick Start Playing with a CD, Tape, or MD (Using MIX IN Jack) Using the TD-6V’s MIX IN jack allows you to play along with a CD or other external audio sources.
52 Using the TD-6V As a General MIDI Sound Module The TD-6V features GM mode, allowing it to play back GM scores (music data for GM sound generators) from an External Sequencer. The TD-6V has a function that lets you mute only the drum sounds in GM mode, making this a very useful feature.
53 Advanced Use Advanced Use TD-6KV_e.book 53 ページ ２００５年１月２４日 月曜日 午後７時４分.
54 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Parameters That Can Be Set Here fig.01-001.e About Drum Kits and the Drum Kit Screen About the Drum Kits A drum kit is a collection of settings, including how each pad’s sound is played, effects settings, hi-hat control pedal settings, etc.
55 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 About the Drum Kit Screen The screen displayed when [KIT] is pressed is referred to as the Drum Kit screen. fig.01-003ai 1 Drum Kit Number Displays the number of the currently selected drum kit. 2 Drum Kit Name The name of the currently selected drum kit is displayed.
56 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Choosing on the TD-6V 1. Press [KIT], then [EDIT]. [KIT] and [EDIT] light. fig.KIT-INST_50 2. Press [ENTER ]. The instrument selection screen appears. fig.01-008_50 3. Hold down [SHIFT] and press [ ] or [ ] to select the trigger input number for the pad being set.
57 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 Locking the Setting Screen While Editing One Instrument (Note Chase) Note Chase is a function in which a pad is selected either by striking the pad or when MIDI data corresponding to that pad is received.
58 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Choosing an Instrument (Inst) Select the instrument you want to sound when the pad is struck. To see which instruments can be selected here, refer to “Drum Instrument List” (p. 120). No sound is played if the pads are struck when the instrument is set to “1024 OFF.
59 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 Adjusting the Volume of the Pad ( Level) Adjusts the volume of the instrument. Raising the value will increase the volume. With a setting of “0,” no sound is produced. Make the adjustment here when correcting the volume balance between instruments.
60 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Ambience Settings (AMBIENCE) Here you can choose (on a per drum kit basis) the location, room size, wall material, etc. 1. Press [KIT], then [EDIT]. [KIT] and [EDIT] light. 2. Press [ ] to select “AMBIENCE.
61 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 Changing the Wall Surface Material (Wall Type) Select the surface material of the walls in the room in which the drums are played. fig.01-027_50 WallType (Wall Type): WOOD, PLASTER, GLASS WOOD: Simulates the sound of a wood-walled room producing a warm sound.
62 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Equalizer Settings (EQUALIZER) A two-band equalizer (for high and low frequency ranges) is used to adjust the sound of each drum kit. An equalizer lets you boost or cut specified frequency ranges to adjust the tone.
63 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 6. Strike the pad you wish to set. The setting screen for the struck pad appears. 7. Press [+] or [-] to make the setting. fig.01-036ai.e 8. When you finish making settings, press [KIT] to end the procedure.
64 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Pitch Control with the Hi-Hat Control Pedal On/Off for Each Pad (Pitch Control Assign) Pitch Control is a function that lets you change the pitch of an instrument assigned to a pad according to the amount the hi- hat control pedal is pressed.
65 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 “CH10Priority (Channel 10 Priority)” to determine whether the instrument (the drum kit part) or the percussion set instrument (the percussion part) is to be played when the note number is received (SETUP/MIDI COMMON/CH10Priorty; p.
66 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Overall Drum Kit Settings (COMMON) Make the settings for each drum kit. 1. Confirm that [CLICK] is not lit. If this lights, press [CLICK] to extinguish it. 2. Press [KIT], then [EDIT]. [KIT] and [EDIT] light.
67 Chapter 1 Creating Your Own Drum Kit (Kit Edit) 1 Naming the Drum Kit (Kit Name) Each kit can be given a name of up to 8 characters. Press [ ] or [ ] to move the cursor (under bar) to the character you want to change, then press [+] or [-] to select the character.
68 Chapter 1 Creating Your Own Drum Kit (Kit Edit) Restoring the Factory Settings for the Edited Drum Kit You can restore reconfigured drum kits to their original factory conditions. Drum Kit Copy Function Follow the procedure described on p. 67 to select a drum kit marked with “ ” (P01–P99) as the copy source.
69 2 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) Parameters That Can Be Set Here fig.02-001.e About the Screen Display Notation Used in the Screen Trigger input numbers and names are indicated in pad and trigger settings screens.
70 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) 3. Press [ENTER ]. fig.02-002ai.e 4. Strike the pad you wish to set. The setting screen for the struck pad appears. You can also make your selection by holding down [Shift] and pressing [ ] or [ ].
71 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) 2 4. Disconnect the connecting cable, then connect two pads to TRIGGER INPUT 5/6 and 7/8 using the optional cable (PCS-31). When connecting the pads, refer to the instructions in “Connecting Two Pads to Trigger Inputs 5/6 (TOM2/ AUX) and 7/8 (TOM3/4)” (p.
72 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) fig.02-006_50 Sensitivity: 1–16 Setting the Minimum Levels for the Pads (Threshold) This setting allows a trigger signal to be received only when the pad is struck harder than a specified force.
73 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) 2 SPLINE: Extreme changes are made in response to the force used to strike the pad. fig.02-013.e LOUD1, LOUD2: Changes made in response to the striking force are minor, maintaining a volume level at which it is easy to play.
74 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) Adjusting the Trigger Signal Detection Time (Scan Time) Since the rise time of the trigger signal waveform may differ slightly depending o.
75 Chapter 2 Making the Pad and Trigger Settings (SETUP/TRIG) 2 Making the settings While stepping on the pad being used for the kick, raise the “Mask Time” value until there is no more bouncing (sounds made by the rebounding of the beater).
76 Chapter 3 Global Settings for the TD-6V (SETUP/UTILITY, Factory Reset) Parameters That Can Be Set Here fig.03-001.e Making the Global Settings (UTILITY) Overall settings that apply to the entire TD-6V. 1. While holding down [SHIFT], press [EDIT (SETUP)].
77 Chapter 3 Global Settings for the TD-6V (SETUP/UTILITY, Factory Reset) 3 Backing Instruments Volume Control (Backing Level) This adjusts the volume of the backing part (Parts 1–4). Raising the value will increase the volume. With a setting of “0,” no sound is produced.
78 Chapter 3 Global Settings for the TD-6V (SETUP/UTILITY, Factory Reset) Preview Volume Control (Preview Velocity) This sets the velocity used when an instrument is previewed. Raising the value will increase the volume. With a setting of “0,” no sound is produced.
79 4 Chapter 4 Setting the Metronome (Click Edit) Parameters That Can Be Set Here fig.04-001.e Switching the Click On/Off (Click) You can switch the click sound on and off by pressing [CLICK]. [CLICK] lights while the click sound is set to be played. fig.
80 Chapter 4 Setting the Metronome (Click Edit) Setting the Time Signature (Time Signature) Specify the time signature of the click sound.When the numerator is set to “0,” no accent is added to the first beat. The metronome click sound then plays at a fixed volume.
81 5 Chapter 5 Editing Songs (SONG Edit) Parameters That Can Be Set Here fig.05-001a.e About Songs and the Song Screen About Songs The TD-6V’s sequencer organizes music into six parts. The Drum Kit part is used to record/play back what is played on the pads.
82 Chapter 5 Editing Songs (SONG Edit) fig.05-001.e Only the performance data is recorded to the drum kit part. When the song is played back, the settings of instruments and effects etc. of the current selected drum kit are used. About the Song Screen The screen that appears when [SONG] is pressed is called the Song screen.
83 Chapter 5 Editing Songs (SONG Edit) 5 Choosing a Song Part settings are switched when a song is selected. To see which songs can be selected here, refer to “Preset Song List” (p. 128). Choosing from a Category (Song Category) Select songs by searching the category names.
84 Chapter 5 Editing Songs (SONG Edit) Even when “9 Perc Only” or “10 Special” is selected for the percussion set, the buttons still light up according to the note numbers. • The correspondence between the lighted buttons and note numbers is predetermined and cannot be changed.
85 Chapter 5 Editing Songs (SONG Edit) 5 Overall Song Settings ( COMMON) Make the settings for each song. • If you want to save any changes made to Preset song settings, first copy the song to a User Song before making the changes (SONG/COPY; p. 89).
86 Chapter 5 Editing Songs (SONG Edit) Playing Back the Song from the First Note/Event (Quick Play) This is an auxiliary function available when “LOOP” or “1SHOT” is specified as the Play Type for the song (SONG/ COMMON/Play Type; previous section).
87 Chapter 5 Editing Songs (SONG Edit) 5 Naming a Song (Song Name) You can use up to eight characters when naming a User song. Press [ ] or [ ] to move the cursor (under bar) to the character you want to change, then press [+] or [-] to select the character.
88 Chapter 5 Editing Songs (SONG Edit) Choosing Percussion Set and Instruments (Percussion Set, Inst) Select a percussion set for the percussion part and instruments for Parts 1–4. Percussion Part The TD-6V features ten Preset percussion sets that are ready to use.
89 Chapter 5 Editing Songs (SONG Edit) 5 Adjusting the Stereo Position (Pan) Adjusts the pan (the perceived location of the sound between the left and right speakers). The effect set here applies only when connected in stereo. Percussion parts do not feature the Pan setting.
90 Chapter 5 Editing Songs (SONG Edit) 7. Press [+] or [-] to select copy destination song. You can select a song that has not yet been used by holding down [SHIFT] and pressing [STOP ]. New User songs are indicated by “ ” in the display. fig.05-031ai.
91 Chapter 5 Editing Songs (SONG Edit) 5 Erasing Performance Data in a Song (ERASE) This erases the User song. Only the performance data is erased, and the beat, measure length, parts, and the song’s other settings are left intact. You can also erase specific parts.
92 Chapter 6 Recording a Song (Realtime Recording) Parameters That Can Be Set Here fig.06-001.e What is played on the pads or on an external MIDI keyboard can be recorded ( Realtime Recording ). The performance of the hi-hat control pedal is also recorded.
93 Chapter 6 Recording a Song (Realtime Recording) 6 How To Record (RECORDING STANDBY) 1. Prepare for recording using the procedure described in “Preparations for Recording” (p. 92). 2. Press [SONG] ➝ [REC ]. [PLAY ] flashes, while [SONG], [REC ] and [CLICK] light up.
94 Chapter 6 Recording a Song (Realtime Recording) Quantize During Recording (Quantize) “ Quantize ” is a function that corrects mistakes or discrepancies in the timing of the performance being recorded. Timing problems almost always occur when recording performances using pads, a MIDI keyboard, or other instruments.
95 7 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) Parameters That Can Be Set Here fig.07-005.e About MIDI MIDI (Musical Instrument Digital Interface) is a standard that allows performance data and other information to be exchanged among electronic musical instruments and computers.
96 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) fig.07-003.e When used as a sound module, the TD-6V can receive on up to six of the sixteen MIDI channels (16 channels in GM mode).
97 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) 7 Automatically Switching Instrument Settings Screens (Note Chase) Note Chase is a function in which a pad is selected either by striking the pad or when MIDI data corresponding to that pad is received.
98 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) Synchronizing with an External MIDI Device (Sync Mode) This section discusses the settings that allow an external MIDI sequencer and the TD-6V’s sequencer to be synchronized.
99 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) 7 The settings screen does not appear in GM mode. fig.07-013_50 CH10Priorty (Channel 10 Priority): KIT, PERC KIT (Drum Kit Part): When overlapping note numbers are received, the drum kit part’s instrument (the pad instrument) is sounded.
100 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) While in GM mode, “ ” appears in the drum kit screen. fig.07-015aai fig.07-015_50 GM Mode: OFF, ON Preventing the TD-6V from Switchin.
101 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) 7 Set the Device ID (Device ID) The setting described here is necessary only when you wish to transmit separate data to two or more TD-6V units at the same time. Do not change this setting in any other case.
102 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) ON: The drum kits are switched when Program Change messages are received from an external MIDI device. MIDI Channel Settings for a Part (MIDI PART) For each part, you can specify the channel on which the TD-6V will receive and transmit MIDI messages.
103 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) 7 Saving Data to an External MIDI Device (BULK DUMP) You can save the TD-6V’s drum kits, songs, general settings, and more to an external MIDI sequencer.
104 Chapter 7 Making the MIDI Settings (SETUP/MIDI, BULK DUMP) Returning Saved Data to the TD-6V This returns settings that have been saved to a sequencer or other external MIDI device back to the TD-6V. At this time, the TD-6V’s data is overwritten.
105 8 Chapter 8 Features Using MIDI and Setting Examples About Transmitting/Receiving Program Changes Drum Kit The drum kit program numbers are always the same as the drum kit numbers; this relationship is fixed, and cannot be changed. Percussion Set Percussion set program numbers are predetermined.
106 Chapter 8 Features Using MIDI and Setting Examples Combining with an External MIDI Sequencer Importing Sequence Data from an External MIDI Device to the TD-6V’s Internal Sequencer You can load data created on another sequencer from the MIDI IN connector and record the data on the TD-6V’s sequencer, then use the data as a song.
107 Chapter 8 Features Using MIDI and Setting Examples 8 3. Match the MIDI channel to be used for transmitting data from the TD-6V and the MIDI channel that the external MIDI sequencer is to use for receiving the data. (SETUP/MIDI PART/CH; p. 102) 4. Start the recording process of the external MIDI sequencer.
MEMO TD-6KV_e.book 108 ページ ２００５年１月２４日 月曜日 午後７時４分.
109 Appendices Appendices TD-6KV_e.book 109 ページ ２００５年１月２４日 月曜日 午後７時４分.
110 Troubleshooting This section outlines points to check if you experience problems, and what to do about them. No Sound No Sound Has the [VOLUME] been lowered? ➝ Rotate the [VOLUME] knob to be sure. Is Local control set to “OFF?” (SETUP/MIDI COMMON/LocalControl; p.
111 Troubleshooting Appendices No sounds from pads connected to Trigger Inputs 6 (AUX) and 8 (TOM4) Have you made correct trigger settings? (SETUP/TRIG TYPE; p. 69) ➝ Change the settings if you are connecting two pads to Trigger Inputs 5/6 (TOM2/AUX) and 7/8 (TOM3/4).
112 Troubleshooting Are you playing a new User song? ➝ Play back a song that contains performance data. New User songs are indicated by “ ” in the display. Is the volume level of the backing part and percussion part set to “0?” (SETUP/UTILITY/PercPartLevel, BackingLevel; p.
113 Troubleshooting Appendices Drum Kit Does Not Sound As Intended Pressing [SHIFT] + [KIT] (Preview) Starts Playback of the Song Is the Pad Pattern function (a feature that starts performance of songs when a pad is struck) specified for the selected pad? (KIT/CONTROL/Pad Ptn; p.
114 Troubleshooting Wrong Sound Plays Is there a mistake in the head and rim selection? (p. 55) ➝ With some parameters, you can make separate settings for the head and rim. At this time, confirm the trigger type appearing in the upper right of the screen, then make the settings.
115 Troubleshooting Appendices Problems Operating the TD-6V Striking Pads Does Not Switch the Settings Screen Is the pad’s settings screen locked? (SETUP/MIDI COMMON/Note Chase; p. 57, p. 97) ➝ Press [+] to set this to “ON.” You can press [SHIFT] + [ ] or [ ] to switch to other pads’ settings screens.
116 Messages and Error Messages This section explains the meaning of the various error messages and other messages that the TD-6V may display, and describes the measures to take when these appear. When [EXIT] appears as shown in the following figure, you can press [EXIT] to dismiss the message.
117 Messages and Error Messages Appendices Song Lock ON! fig.e-012_50 Song Lock is on for this song; it cannot be edited or recorded. Set Song Lock to “OFF” (SONG/COMMON/Song Lock; p. 86). Empty Song! fig.e-013_50 This song contains no performance data; it cannot be edited.
118 Drum Kit List No. Drum Kit Name Remark Featured Kits 1 RoseWood 2 BeeBop X x-stick 3 Yo Yo 4 RokCncrt 5 LtnPerc+ Pad Pattern (SNR_H,CR1_R) 6 Orch Set 7 TblaTun+ Pad Pattern (RD_H,RD_R) 8 1ManBnd+ .
119 Drum Kit List Appendices Jazz Kits 61 BrshSwel 62 Jazz 63 Sizzle 64 JazzOne Electronic Kits II 65 HipHop 66 R&B1 67 R&B2 68 Dance808 Funk Kits 69 JazzFunk 70 PowrFusn 71 Pocket Ambience Kits 72 Dome 73 JzThet X x-stick 74 TileRoom 75 GigaHall 76 Cave 77 Dry&Wet No.
120 Drum Instrument List No. Name Remark KICK 1 DblHeadK 2 Sharp K 3 Acous K 4 Meat K 5 R8 Low K 6 R8 Dry K 7 WdBeatrK 8 Open K 9 VintageK 10 26"DeepK 11 ThickHdK 12 Round K 13 Medium K 14 BigRoo.
Appendices Drum Instrument List 121 264 Std2 1 S 265 Std2 2 S 266 Room 1 S 267 Room 2 S 268 Power1 S 269 Power2 S 270 Gate S 271 Jazz 2 S 272 Jazz 3 S 273 Funk S 274 Funk RS 275 Bop S 276 Bop RS 277 P.
122 Drum Instrument List No. Name Remark 549 Elec T1 550 Elec T2 551 Elec T3 552 Elec T4 553 Elec T5 554 Elec T6 555 TR808 T1 556 TR808 T2 557 TR808 T3 558 TR808 T4 559 TR808 T5 560 TR808 T6 HI-HAT 56.
Appendices Drum Instrument List 123 819 KungFoo 820 Pistol 821 Gun Shot 822 Glass 823 Hammer 824 Bucket 825 Barrel 826 TrashCan 827 Af Stomp 828 Bounce 829 CuicaHit 830 Monster 831 AirDrive 832 Car Do.
27 28 29 31 33 35 30 32 34 39 40 41 43 45 47 42 44 46 36 38 37 87 88 84 86 85 51 52 53 55 57 59 54 56 58 48 50 49 63 64 65 67 69 71 66 68 70 60 62 61 75 76 77 79 81 83 78 80 82 72 74 73 C2 C3 C4 C5 C6 26 25 96 89 91 93 95 90 92 94 C7 24 C1 23 19 21 18 20 22 Note No.
27 28 29 31 33 35 30 32 34 39 40 41 43 45 47 42 44 46 36 38 37 87 88 84 86 85 51 52 53 55 57 59 54 56 58 48 50 49 63 64 65 67 69 71 66 68 70 60 62 61 75 76 77 79 81 83 78 80 82 72 74 73 C2 C3 C4 C5 C6 26 25 96 89 91 93 95 90 92 94 C7 24 C1 23 19 21 18 20 22 Note No.
126 Backing Instrument List PC CC0 Name Voices PIANO 1 0 Piano 1 1 8 Piano 1w 2 16 Piano 1d 1 2 0 Piano 2 1 8 Piano 2w 2 3 0 Piano 3 1 8 Piano 3w 2 4 0 Honky-tonk 2 8 Honky-tonk w 2 E. PIANO 5 0 E.Piano 1 1 8 Detuned EP 1 2 24 60’s E.Piano 1 64 FM+SA EP 2 65 Hard Rhodes 2 6 0 E.
Backing Instrument List 127 Appendices SYN. BRASS 63 0 Synth Brass1 2 8 Synth Brass3 2 16 AnalogBrass1 2 64 Synth Brass5 2 65 Poly Brass 2 66 Quack Brass 2 67 Octave Brass 2 64 0 Synth Brass2 2 8 Synt.
128 Preset Song List No. Song Name Time Sig Length Tempo Type DRUMS 1 DRUMS 4/4 8 124 LOOP ROCK 2 US ROCK 4/4 35 128 1SHOT 3 ACO ROCK 4/4 26 120 1SHOT 4 8BT'ROK1 4/4 36 114 1SHOT 5 8BT'ROK2 .
129 Preset Song List Appendices LATIN 85 LATIN1 4/4 41 120 1SHOT 86 LATIN2 4/4 41 108 1SHOT 87 LATIN3 4/4 33 130 1SHOT 88 MAMBO 4/4 36 182 1SHOT 89 MERENGUE 4/4 36 207 1SHOT 90 SALSA1 4/4 30 115 1SHOT.
130 Parameter List Drum Kit Parameters KIT KIT/INST KIT/AMBIENCE KIT/EQUALIZER KIT/CONTROL +: This setting cannot be made in GM mode. KIT/COMMON *1: Parameter Value Drum Kit (p. 55) Drum Kit 1–99 Parameter Value Inst (p. 58) Instrument 1–1024 Inst Group (p.
131 Parameter List Appendices KIT/COPY KIT/EXCHANGE Song Parameters SONG +: This setting cannot be made in GM mode. SONG/COMMON +: This setting cannot be made in GM mode. #: This setting cannot be made when the preset song is selected. *1: SONG/PART:Perc +: This setting cannot be made in GM mode.
132 Parameter List SONG/COPY +: This setting cannot be made in GM mode. SONG/DELETE +: This setting cannot be made in GM mode. SONG/ERASE +: This setting cannot be made in GM mode. Setup Parameters SETUP/UTILITY +: This setting cannot be made in GM mode.
133 Parameter List Appendices SETUP/MIDI COMMON +: This setting cannot be made in GM mode. SETUP/MIDI PART +: This setting cannot be made in GM mode. SETUP/GM PART -: This setting can be made in GM mode only. SETUP/BULK DUMP SETUP/FactoryReset Parameter Value Note Chase (p.
134 Parameter List Click Parameters CLICK +: This setting cannot be made in GM mode. Song Recording Recording Standby +: This setting cannot be made in GM mode. Tempo Tempo +: This setting cannot be made in GM mode. Parameter Value Click Level (p. 79) Click Level 0–127 + Time Sig (p.
135 Appendices Function... Basic Channel Mode Note Number : Velocity After Touch Pitch Bend Control Change Program Change System Exclusive System Common System Real Time Aux Messages Notes Transmitted.
136 Function... Basic Channel Mode Note Number : Velocity After Touch Pitch Bend Control Change Program Change System Exclusive System Common System Real Time Aux Messages Notes Transmitted Recognized.
137 Appendices Function... Basic Channel Mode Note Number : Velocity After Touch Pitch Bend Control Change Program Change System Exclusive System Common System Real Time Aux Messages Notes Transmitted.
138 Inst Level Head Inst Level Rim Amb Send Level Amb Send Level Inst Level Head Inst Level Rim Amb Send Level Amb Send Level Inst Level Head Inst Level Rim Amb Send Level Amb Send Level Inst Level He.
139 Appendices Specifications TD-6V: Percussion Sound Module (Conforms to General MIDI System) Maximum Polyphony 64 Voices Instruments Drum Instruments: 1,024 Backing Instruments: 262 Drum Kits 99 Eff.
140 Index A AC Adaptor Jack ..................................................................... 18 Acoustic Drum Trigger .......................................................... 75 Advanced Trigger Parameter .......................................
141 Index Index I INC/+, DEC/- Button ............................................................ 17 Indicator ............................................................................. 32, 69 INST .................................................
142 Index Pitch Ctrl (Pitch Control Assign) .......................................... 64 PLAY Button ............................................................................ 16 Play Type ...........................................................
143 Index Index U User Song ................................................................................. 81 UTILITY .................................................................................... 76 V Variation Tone .........................
MEMO TD-6KV_e.book 144 ページ ２００５年１月２４日 月曜日 午後７時４分.
MEMO TD-6KV_e.book 145 ページ ２００５年１月２４日 月曜日 午後７時４分.
MEMO TD-6KV_e.book 146 ページ ２００５年１月２４日 月曜日 午後７時４分.
To resize thickness, move all items on the front cover to left or right IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
03458934 5RCC To resize thickness, move all items on the front cover to left or right (6.54 mm) * All product names mentioned in this document are trademarks or registered trademarks of their respective owners. 202 Copyright © 2003 ROLAND CORPORATION All rights reserved.
An important point after buying a device Roland TD-6V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Roland TD-6V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Roland TD-6V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Roland TD-6V you will learn all the available features of the product, as well as information on its operation. The information that you get Roland TD-6V will certainly help you make a decision on the purchase.
If you already are a holder of Roland TD-6V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Roland TD-6V.
However, one of the most important roles played by the user manual is to help in solving problems with Roland TD-6V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Roland TD-6V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
