Instruction/ maintenance manual of the product CUBE-60 Roland
Go to page of 12
Owner’s Manual Thank you, and congratulations on your choice of the Roland CUBE-60 Guitar Amplifier. These sections provide important information concerning the proper operation of the unit.
2 30 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION : RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
3 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. .......................................................................................................... 002a • Do not open or perform any internal modifica- tions on the unit.
4 015 • Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords—the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/amperes) for the extension cord.
5 IMPORTANT NOTES 291b In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2, 3 and 4, please read and observe the following: Power Suppl.
6 Panel Descriptions Control Panel fig.01 1. INPUT Jack Connect your guitar here. 2. SELECT Switch Switches you between the JC CLEAN and LEAD channels. You can confirm which channel is selected by checking the indicator’s color (JC CLEAN: green; LEAD: red).
7 Panel Descriptions * All product names mentioned in this document are trademarks or registered trademarks of their respective owners, and are not related to Roland Corporation. In this manual, these names are used as appropriate ways to indicate sounds that are simulated using COSM technology.
8 Panel Descriptions Rear Panel 1. FOOT SW (Foot Switch) Jack Foot switches (the optional BOSS FS-5U) are connected here. * Set the polarity switch as shown below. fig.06 (CH SELECT) Switches JC CLEAN/LEAD channels. (EFX) Switches on and off of EFX. (DELAY/REVERB) Switches on and off of DELAY/REVERB.
9 Sample Settings Alternative Metal The perfect sound for heavy, sharp riffs. Select the high-gain R-FIER amp, then use the equalizer to boost the low end even more. You can add even more to the distortion’s edge by raising the presence. Used with a humbucking pickup in the rear position, it results in an extreme distortion effect.
10 Sample Settings Dynamic Style DYNA AMP is an original amp that uses relative picking strength to create changes in distortion depth. First, adjust the GAIN knob so that a clean tone is obtained with soft picking and deep distortion is obtained when you pick hard.
11 Main Specifications Rated Power Output 60 W Nominal Input Level (1 kHz) INPUT: -10 dBu/1 M Ω Speaker 30 cm (12 inches) Controls POWER Switch, SELECT Switch <JC CLEAN Channel> BRIGHT Switch,.
SD000453 1GT Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.
An important point after buying a device Roland CUBE-60 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Roland CUBE-60 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Roland CUBE-60 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Roland CUBE-60 you will learn all the available features of the product, as well as information on its operation. The information that you get Roland CUBE-60 will certainly help you make a decision on the purchase.
If you already are a holder of Roland CUBE-60, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Roland CUBE-60.
However, one of the most important roles played by the user manual is to help in solving problems with Roland CUBE-60. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Roland CUBE-60 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
