Instruction/ maintenance manual of the product R9974 Roberts Radio
Go to page of 20
3 Band PLL Synthesised Portable Mains Battery Radio Please read this manual before use ROBER TS Sound for Generations R9974.
2 Controls ........................................................................... 3-4 Display .................................................................................5 Battery operation ...................................................
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 3 Controls (T op) 13 6 8 7 10 5 4 9 1. On/Of f button 2. LCD display 3. Band/Step button 4. Radio alarm button 5. Buzzer alarm button 6. Scan/T ime set button 7.
4 Controls 1 1. Headphone socket 12. DC input socket 12 11.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 5 a cd f e g h i j a. W aveband indicators b. Frequency indicators c. Sleep/Snooze indicators d. PM indicator e. Time set indicator f. T ime indicators g.
6 Battery operation 1. Release the catch securing the rear door of your radio. 2. Insert four LR20 (D size) batteries into the spaces in the compartment. T ake care to ensure all batteries are inserted with the correct polarity as shown inside the battery compartment.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 7 Setting the clock 1. The clock will start running when the batteries are installed or when the radio is connected to the mains supply . The display will show " -:--" together with the real time symbol .
8 Operating your radio Y our radio is equipped with four tuning methods:- Scan tuning, Manual tuning, Search tuning and Memory preset tuning. Scan tuning 1. Press the On/Off button to switch on your radio. 2. Select the required waveband by repeatedly pressing the Band button.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 9 Manual tuning 1. Press the Power button to turn on the radio. 2. Select the required waveband by repeatedly pressing the Band button. For the FM waveband fully extend the T elescopic aerial and set it at an angle of 45 degrees.
10 Search tuning 1. Press the Power button to turn on the radio. 2. Select the required waveband by repeatedly pressing the Band button. For the FM waveband fully extend the T elescopic aerial and set it at an angle of 45 degrees. 3. Press and hold down either the Tuning up or Tuning down buttons for more than 0.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 11 Storing stations in preset memories There are 5 memory presets for each waveband. 1. Press the Power button to turn on the radio. 2. T une to the required station using one of the methods previously described.
12 Recalling preset stations 1. Press the Power button to turn on the radio. 2. Select the required waveband by repeatedly pressing the Band but- ton. 3. Momentarily press the required Preset button , the preset number and station frequency will appear in the display .
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 13 Setting the radio alarm When the radio alarm is selected the radio will turn on and play the station selected during the alarm set up. The radio alarm will sound for one hour unless turned off by pressing the Power button .
14 Setting the HWS (Humane W ake System) buzzer alarm A beep tone will sound when using the HWS alarm. The alarm beep will increase in volume every 15 seconds for one minute followed by one minutes silence before repeating the cycle. The HWS alarm will sound for one hour unless turned off by pressing the On/Off button .
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 15 Snooze function 1 . Whilst the alarm is sounding pressing any button (except the Power button ) will activate the snooze function. The Radio or Buzzer alarms will be silenced for 5 minutes.
16 T uning step size In Europe and other parts of the world MW tuning steps are 9kHz, in America the MW tuning step size is 10kHz. On FM tuning steps can be set to either 50 or 100kHz. 1. Ensure that your radio is switched off. 2. Press and hold down the Step/Band button for 2 sec.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 17 Display backlight 1. The display backlight will be switched on for approximately 15 seconds when any button is pressed, during station scanning and when the alarm is operating.
18 Circuit Features Loudspeaker 75mm 4ohm full range Output Power 800mW Headphone socket 3.5mm dia Aerial System FM T elescopic aerial MW/L W Ferrite Rod Specifi cations Power Requirements Mains (via AC adaptor) AC 230 volts, 50Hz only/DC 6V 400mA Batteries 4 x LR20 (D size) Battery Life Approx.
If you need any further advice, please call our T echnical Helpline on :- 020 8758 0338 (Mon-Fri) 19 Guarantee This instrument is guaranteed for twelve months from the date of delivery to the original owner against failure due to faulty w orkmanship or component breakdown, subject to the procedure stated below .
ROBERTS RADIO TECHNICAL SER VICES 97-99 Worton Road Isleworth Middlesex TW7 6EG T echnical Helpline :- 020 8758 0338 (Mon-Fri during offi ce hours) Website: http://www .
An important point after buying a device Roberts Radio R9974 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Roberts Radio R9974 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Roberts Radio R9974 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Roberts Radio R9974 you will learn all the available features of the product, as well as information on its operation. The information that you get Roberts Radio R9974 will certainly help you make a decision on the purchase.
If you already are a holder of Roberts Radio R9974, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Roberts Radio R9974.
However, one of the most important roles played by the user manual is to help in solving problems with Roberts Radio R9974. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Roberts Radio R9974 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
