Instruction/ maintenance manual of the product 8050C ritetemp
Go to page of 10
1-405-061 Made in China Install guide 8050C Customer Support: 888-515-2585 or Visit our website www .ritetemp-thermostats.com HEA T COOL A UT O ON O FF FA N H E A T C O O L A U T O O N OF F F A N ENGL.
Install guide 8050C 1 Location Caution T ools T o avoid electrical shock and to prevent damage to the furnace, air conditioner , and thermostat, disconnect the power supply before beginning work. This can be done at the circuit breaker , or at the appliance.
3 Remove old unit 2 Label Wires from Old Unit 4 Mount the 8050C . Separate front from back of unit. Press up on the catch on the bottom of the thermostat and swing the body away from the base, lift up to remove the body from the base. . Hold the base against the wall, with the wires coming through the opening below the terminal block.
PG 5 7 Install Batteries The 8050C requires batteries to operate your system and retain its programming in memory . . Switch MODE switch to OFF and the F AN switch to AUTO. . Insert 2 AA alkaline batteries according to the polarity noted in the compartment.
PG 8 PG 7 Please refer back to these guidelines for safe and secure wire connections. . T ake care not to damage the labels for each wire in handling. . Strip insulation 3/8 in. (9.5mm) from wire ends. . Connect labeled wires only to a terminal with corresponding letter .
PG 10 PG 9 RH G Y W C From Fu r n ace And AC unit R or RC G Y W C From Fu r n ace And AC unit RH Go T o Page 13 Go T o Page 14 Go T o Page 12 RH W C From Fu r n ace G Go T o Page 17 Go T o Page 15 Go .
PG 1 1 PG 12 Go T o Page 10 STEP 1 - Connect the R (or RH) wire to the RH terminal on the thermostat. This connects to the Heater Power . STEP 2 - Connect the W wire to the W terminal on the thermostat. This connects the heater control line to the thermostat.
PG 14 PG 13 R G Y W C RH or Fr om Fu rna ce an d A C u nit STEP 1 - Connect the Y wire to the Y terminal on the thermostat. This connects to the Cooler compressor . STEP 2 - Connect the RH or R wire to the RH terminal on the thermostat. This connects the Heater/Cooler Power .
PG 16 PG 15 Go T o Page 10 Go T o Page 10 NOTE: Wires marked with the dotted line are optional. STEP 1 - Connect the G wire to the G terminal on the thermostat. This connects the Fan. STEP 2 - Add a jumper wire between W and Y . STEP 3 - Connect the Y wire to the Y terminal on the thermostat.
8050C Features PG 17 PG 18 STEP 1 - Connect the G wire to the G terminal on the thermostat. This connects the Fan. STEP 2 - Add a jumper wire between W and Y . STEP 3 - Connect the Y wire to the Y terminal on the thermostat. This connects the Compressor .
An important point after buying a device ritetemp 8050C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ritetemp 8050C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ritetemp 8050C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ritetemp 8050C you will learn all the available features of the product, as well as information on its operation. The information that you get ritetemp 8050C will certainly help you make a decision on the purchase.
If you already are a holder of ritetemp 8050C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ritetemp 8050C.
However, one of the most important roles played by the user manual is to help in solving problems with ritetemp 8050C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ritetemp 8050C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
