Instruction/ maintenance manual of the product 8035C ritetemp
Go to page of 9
Install guide 8035C 1-402-051 Customer Support: 888-515-2585 or Visit our website www.ritetemp-thermostats.com RESET MENU PROG RESET MENU PROG ENGLISH Printed in China.
Install guide 8035C 1 Location Caution Tools To avoid electrical shock and to prevent damage to the furna ce, air conditioner, and thermostat, disconnect the power supply before beginning work. This can be done at the circuit breaker, or at the appliance .
3 Mount the 8035C ï Separate front from back of unit. Press up on the catch on bottom of thermostat and swing the body away from the base, lift up to remove the body from the base. Hold the base against the wall, with the wires coming through the opening below the terminal block.
PG 5 AA AA Please be aware of the following power options. 1) The 8035C can run on batteries only. (2AA Alkaline) The batteries will last well over 1 year. If the batteries are not replaced the thermostat will stop working. 2) The 8035C can run on the C wire if available.
PG 8 PG 7 Please refer back to these guidelines for safe and secure wi re connections. ï Take care not to damage the labels for each wire in handling. ï Strip insulation 3/8 in. (9.5mm) from wire ends. ï Connect labeled wires only to a terminal with corresponding letter.
RESET MENU PROG RESET MENU PROG 7 Wire Connections cont When you have finished connecting the wires, close cover and attach control unit to wall unit. Hook the top of the body onto the base, swing the body down, and snap the body onto the base. If you do not find the wiring information for your system try our website at www.
PG 11 PG 12 STEP 1 - Connect the R (or RH) wire to the RH terminal on the thermostat. This connects the Heater Power to the thermostat. STEP 2 - Connect the W wire to the W terminal on the thermostat. This connects the heater control line to the thermostat.
PG 14 PG 13 From Furnace and AC unit G W Y RH RC C R G Y W C RH or From Furnace and AC unit STEP 1 - Connect the Y wire to the Y terminal on the thermostat. This connects to the Cooler compressor. STEP 2 - Connect the RH or R wire to the RH terminal on the thermostat.
PG 16 PG 15 STEP 1 - Connect the G wire to the G terminal on the thermostat. This connects the Fan. STEP 2 - Add a jumper wire between W and Y. STEP 3 - Connect the Y wire to the Y terminal on the thermostat. This connects the Compressor. STEP 4 - Connect the O or B wire to the O or B terminal on the thermostat.
An important point after buying a device ritetemp 8035C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ritetemp 8035C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ritetemp 8035C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ritetemp 8035C you will learn all the available features of the product, as well as information on its operation. The information that you get ritetemp 8035C will certainly help you make a decision on the purchase.
If you already are a holder of ritetemp 8035C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ritetemp 8035C.
However, one of the most important roles played by the user manual is to help in solving problems with ritetemp 8035C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ritetemp 8035C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
