Instruction/ maintenance manual of the product 401-014 ritetemp
Go to page of 9
401-014 Customer Support: 888-515-2585 or Visit our website www.ritetemp-thermostats.com Install guide 8022C HEAT COOL AUTO ON OFF FAN PM F SET TEMP HEAT HEAT COOL AUTO ON OFF FAN PM F SET TEMP HEAT.
Install guide 8022C 1 Location Caution Tools To avoid electrical shock and to prevent damage to the furna ce, air conditioner, and thermostat, disconnect the power supply before beginning work. This can be done at the circuit breaker, or at the appliance .
2 Remove old unit 3 Mount the 8022C Caution Switch electricity to the furnace and air conditioner OFF; then proceed with the following steps. Remove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the side or front.
PG 5 PG 6 4 Before you Connect Wires Caution Do not allow wires to touch each other or parts on thermostat. Wires must be routed through the hole in the back plate, below the terminal block, or they will hit parts on the cover. Please follow these guidelines for safe and secure wire connections.
When you have finished making connections. hook the top of the body onto the base, swing the body down, and snap the body onto the base. 5 Install Batteries 6 Check Unit The 8022C requires batteries to operate your furnace and retain its programming in memory.
Note: If you have an electric furnace system and the blower does not operate after installation, remove the thermostat, turn it over, and find the electric/gas heat selector jumper on the back of the control unit. Switch it to "Elect"(see Diag belo w).
PG 11 PG 12 STEP 1 - Connect the R (or RH) wire to the RH terminal on the thermostat. This connects the Heater Power to the thermostat. STEP 2 - Connect the W wire to the W terminal on the thermostat. This connects the heater control line to the thermostat.
PG 14 PG 13 From Furnace and AC unit G W Y RH RC C R G Y W C RH or From Furnace and AC unit STEP 1 - Connect the Y wire to the Y terminal on the thermostat. This connects to the Cooler compressor. STEP 2 - Connect the RH or R wire to the RH terminal on the thermostat.
The 8022C can be used with most 24 volt gas, oil or electric heating and air conditioning systems, single- stage heat pumps or gas millivolt heating systems. It cannot be used with 120 volt heating systems or multistage heat pumps. Ask The Home Depot for other thermost ats to control those systems.
An important point after buying a device ritetemp 401-014 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ritetemp 401-014 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ritetemp 401-014 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ritetemp 401-014 you will learn all the available features of the product, as well as information on its operation. The information that you get ritetemp 401-014 will certainly help you make a decision on the purchase.
If you already are a holder of ritetemp 401-014, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ritetemp 401-014.
However, one of the most important roles played by the user manual is to help in solving problems with ritetemp 401-014. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ritetemp 401-014 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
