Instruction/ maintenance manual of the product AC9940 RIDGID
Go to page of 16
1 This Miter Saw Utility V ehicle has been engineered and manufactured to our high standar d for dependability , ease of op- eration and operator safety . When properly car ed for , the Miter Saw Utility V ehicle will give you years of rugged, trouble-free performance.
2 n Introduction ...................................................................................................................................................................... 2 n Rules for Safe Operation ......................................
3 RULES FOR SAFE OPERA TION Safe operation of this accessory requir es that you read and understand this operator's manual, the operator’ s manual for the miter saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n KNOW YOUR ACCESSOR Y .
4 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger .
5 UNP ACKING NOTE: Before beginning assembly , check that all parts are included. If you ar e missing any part, do not assemble this accessory . Call 1-800-4-RIDGID or E-mail us at info@rid gidwoodworking.
6 Fig. 3 ASSEMBL Y A TT ACHING THE LOWER FOOT See Figures 1 and 2. n Place stand assembly “flat” on floor . n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat W asher , M8 (4) Lock Nut, M8 (2) n Install bolt, two washers and lock nut as shown.
7 WORKST AND SET -UP See Figures 4 and 5. Before Y ou Start n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n If a compound miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable).
8 ASSEMBL Y MOUNTING MITER SA W See Figures 6 and 7. WARNING: Failure to unplug the tool could r esult in accidental starting causing possible serious personal injury .
9 ASSEMBL Y MOUNTING OTHER BRANDS See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will requir e additional 5/16 in. mounting holes to be drilled.
10 ASSEMBL Y EXTENSION BAR(S) OPERA TION See Figures 10 and 11. Both extension bars may be adjusted to pr ovide maximum workpiece support. T o adjust the extension bars: n Loosen adjustable handle by tur ning counter clockwise. NOTE: Adjustable handle can be repositioned if necessary .
11 FOLDING LEG AND T ABLE n Loosen the r oller foot knob and slide foot extension up. Tighten knob. n Release locking pin and raise foot. n Loosen the extension bar handle and slide extension bar in towards table. Tighten extension bar handle. n Repeat for the other side.
12 ASSEMBL Y TRANSPORTING TOOL See Figure 15. n When hauling the workstand in a vehicle, securely tie it down to prevent movement and possible damage. n Always get help if you need to lift the workstand. When lifting, hold the workstand close to your body .
13 EXPLODED VIEW/REP AIR P AR TS Miter Saw Utility V ehicle Model AC99400 RIDGID parts are at www .ridgidparts.com 1 829859 Rear Roller Extension 2 829758-5 W asher (20 x 10.5 x 1.5) 3 829759-3 Nylock Nut (M10) 4 829799 Rubber Cap 5 829757-6 Hex Head Bolt (M8 x 1.
14 NOTES.
15 W ARRANTY Proof of purchase must be presented when requesting war - ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after . This product is manufactured by One W orld T echnologies, Inc. The trademark is licensed from RIDGID, Inc.
16 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center . Be sure to pr ovide all relevant information when you call or visit. For the location of the authorized service center near est you, please call 1-866-539-1710 or visit us online at www .
An important point after buying a device RIDGID AC9940 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RIDGID AC9940 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RIDGID AC9940 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RIDGID AC9940 you will learn all the available features of the product, as well as information on its operation. The information that you get RIDGID AC9940 will certainly help you make a decision on the purchase.
If you already are a holder of RIDGID AC9940, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RIDGID AC9940.
However, one of the most important roles played by the user manual is to help in solving problems with RIDGID AC9940. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RIDGID AC9940 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
