Instruction/ maintenance manual of the product FV-L030B1 Ricoh
Go to page of 32
1/32 FV -L030 B1 User ’s G uide Rev . 1.01 Small Cubic T ype VGA CCD Monochrome PoCL Camera Link Camera FV -L030B1 User ’s Guide RICOH CO MP A NY , L TD.
2/32 FV -L030 B1 User ’s G uide Rev . 1.01 T ables o f Content s 1 Connector Specifications ............................... .............................. .................... .............................. .................... .. 3 1.1 Camera Link Connector .
3/32 FV -L030 B1 User ’s G uide Rev . 1.01 1 Connector Specifications 1.1 Camera Li nk Connect or SDR (3M) or equiva lent This product is a PoCL type. When a frame grabbe r is PoCL compli ant, DO NOT SUPPLY POW ER FROM THE I/O CONNECTOR. When a frame grabbe r is NOT PoCL compliant, supply power from t he I/O connecto r.
4/32 FV -L030 B1 User ’s G uide Rev . 1.01 1.2 Power-I/O Connector HR10A-7R-6PB （ Hirose ） or equivalent This connector is f or the power supply (12 Vdc) and input /output sig nals. Use HR10A-7P-6S ( Hirose) or equivalent f or the cable side.
5/32 FV -L030 B1 User ’s G uide Rev . 1.01 2 C amera Output T i ming Chart s 2.1 Normal Mod e (Setting 1 0H: 1XX0X XXX) ※ Clock S peed: 36.8181 MHz （ Normal ） 、 24.5454 MH z （ x2/3 ） 、 12.2727 MH z （ x1/3 ） 2.1.1 Horizont al T iming 1 CLK = 81.
6/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.1.2 V ertical T iming 2.1.2.1 Normal Full Sc anning (setting 10H: 1XX 00XXX, 1 1H: XX X0X000) 1 H = 63.5556 μ s, 29.9700 Hz at 30fps 1 H = 31.7778 μ s, 59.9400 Hz at 60fps 1 H = 21.1852 μ s, 89.9100 Hz at 90fps 2.
7/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.1.2.3 1/2 Partial Scan ning (setting 10H: 1XX 01XXX, 1 1H: XX X0X001) 1 H = 63.5556 μ s, 60.0544 Hz at 30fps 1 H = 31.7778 μ s, 120.108 Hz at 60fps 1 H = 21.1852 μ s, 180.163 Hz at 90fps 2.1.2.4 1/4 Partial Scan ning (setting 10H: 1XX 01XXX, 1 1H: XX X0X010) 1 H = 63.
8/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.1.2.5 V ariable Partial S canning ( Setting 10H: 1XX01X XX, 1 1H: XXX0X1 1 1) Internal HD Internal VD Video out EXT_TRIG FIX_TRIG (Common) 10 20 30 40 5 .
9/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.2 Binning Mo de (setting 10H: 1X X1XXXX) Binning Full Scanning Binning Partial Full Scanning Binning 1/2 Partial Scanning Binning 1/4 Partial Scanning Clock Speed (MHz) Normal x2/3 x1/3 Normal x2/3 x1/3 Normal x2/3 x1/3 Normal x2/3 x1/3 Frame Rate (Hz) 180.
10/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.2.2 V ertical T iming 2.2.2.1 Binning Full Sc anning (setting 10 H : 1X X10XX X, 1 1H: X XX0X000) 1 H = 63.5556 μ s, 60.0544 Hz at 30fps 1 H = 31.7778 μ s, 120.108 Hz at 60fps 1 H = 21.1852 μ s, 180.163 Hz at 90fps 2.
1 1/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.2.2.3 Binning 1/2 P artial Scann ing ( setting 10 H: 1XX1 1XXX, 1 1H: XXX 0X001) 1 H = 63.5556 μ s, 1 12.3 78 Hz at 3 0fp s 1 H = 31.7778 μ s, 224.775 Hz at 60fps 1 H = 21.1852 μ s, 337.162 Hz at 90fps 2.
12/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.3 Data Or der on the Ca mera Link Out put DA0 ～ DA9: 10 bit data for one pixel DA0 ～ DA7: 8bit data for one pixe l DA8 DA 5 DA4 DA3 D A2 DA1 D A0 DA.
13/32 FV -L030 B1 User ’s G uide Rev . 1.01 2.4 1 T aps Tr ansferrin g Image （ 1X-1Y ） X W Y H X W -1 Y H X 2 Y H X 1 Y H Tap1 Sep X = 1 Sep Y = 1 X 1 Y H-1 X 2 Y H-1 X W Y H-1 X W -1 Y H-1 X 1 Y 1 X 1 Y 2 X 2 Y 1 X 2 Y 2 X W -1 Y 2 X W Y 2 X W -1 Y 1 X W Y 1 2.
14/32 FV -L030 B1 User ’s G uide Rev . 1.01 3 Camera Operational Mode 3.1 Normal Mod e In this m ode, the images are output continuous ly . 3.1.1 Frame Expo sure 3.
15/32 FV -L030 B1 User ’s G uide Rev . 1.01 3.2 Pulse W idth T rigger Mode In this “pulse width trigger mode” with pos itive po larity , the camera exposure starts at the rising edge of the trigger si gnal and stops at the falling edge of the trigger s ignal.
16/32 FV -L030 B1 User ’s G uide Rev . 1.01 3.2.2 Pulse W idth T rigger Mode (Non-Reset) Note 1: The cam era does NOT switch to normal mode when the long exposure m ode is selected. This tim ing chart shows with the long ex posure mode selected. Note 2: The internal VD signal does not rese t by the trigger signa l.
17/32 FV -L030 B1 User ’s G uide Rev . 1.01 3.3 Edge Pres et Trigger Mode In this “edge preset tr igger m ode”, the camera exposure starts at t he rising edge of the trigger s ignal like the “pulse width trigger m ode” in the previous sec tions.
18/32 FV -L030 B1 User ’s G uide Rev . 1.01 3.3.2 Edge Pres et Trigger Mode (Non-Reset) Note 1: The cam era does NOT switch to normal mode when the long exposure m ode is selected. This tim ing chart shows when the long exposure mode selected. Note 2: The internal VD signal does not rese t by the trigger signa l.
19/32 FV -L030 B1 User ’s G uide Rev . 1.01 3.4 H Reset Mod e Normally , v ideo noise appears when the beginning of trigger si gnal is applied before f inishing the video read-out of the prev ious f rame. This noise is caused by the SU B puls e, which is acti vated to clear al l res idual c harges on the CCD p rior t o a new exposure.
20/32 FV -L030 B1 User ’s G uide Rev . 1.01 4 C ommunication Protocol This camera has a communication function that enables external devises, such as a P C, to control the cam era’ s functions. Please use the “R- CLinkCtrl” comm unication software, or the following c ommunication protoc ol to comm unicate to the cam era: 4.
21/32 FV -L030 B1 User ’s G uide Rev . 1.01 The description of the format is as follows. Name Descriptions SOF S tart of Fram e. Alwa ys set or receive the value as “02H” Device Code This indicates the destination of c ommunication.
22/32 FV -L030 B1 User ’s G uide Rev . 1.01 【 Example Code 】 Reading the data from the com m and 00H Comm and to send: 02H, 00H, 00H, 01H, 0 0H, 03H SOF Device Code Read/Write Page Selection.
23/32 FV -L030 B1 User ’s G uide Rev . 1.01 4.4 Camera C ontrol Co mmand 4.4.1 Camera C ommand Li st The data unit of the each comm and is 1 byte (8bit). The data can be s aved to the EEPROM if there is an “X” in the “Sa ve to EEPROM” colum n in the following list.
24/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. R/W Save to EEPROM Function Initial Dat a Dat a Range 78H R/W X T est pattern sele ction (8bit: D [7.
25/32 FV -L030 B1 User ’s G uide Rev . 1.01 4.4.2 Description s of the C amer a Control C ommands (The underline setti ngs are the factor y default settings) Command No. Command Descriptions 10H: MOD1[70] [Camera function mode setting 1] Initial data: 09H Sets the following camera function mode.
26/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions 12H: MOD3[70] [Camera function mode setting 3] Initial data: 0 Sets the following camera function modes. D[70] D7 D6 D5 D4 D3 D2 D1 D0 D7~D6: Video Out 00: 10bit 01: 8bit 10: 12bit 1 1: No function (Prohibited setting.
27/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions 20H: SVR[70] 21H: SVR[158] [Exposure time (H) of the electronic shutter] Initial Data: SVR[150] = 0, Dat a Range: 0 to 4095 Sets the preset shutter speed (or CCD ex posure time) for electronic shutter .
28/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions 28H: DL Y[70] 29H DL Y[15...8] [Delay time for the trigger] Initial Data: DL Y[70] = 0, Data Range: 0 to 65,535 Sets the delay time from the trigger input signal to the st art of the exposure.
29/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions 78H: TESTP[70] [T est pattern selection] Initial d ata: TEST P[7. .0] = 00H Sets the test patt ern output from the camera.
30/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions A0H: PDC0[70] [Pixel defect correction mode] Initial data: PDC0[7..0] = 0 D[7..0] D7 D6 D5 D4 D3 D2 D1 D0 D7: Write the correction index 0 1 * W rites the coordinates of the comm and, A2 to A5, to the in dex number specified b y the command A1.
31/32 FV -L030 B1 User ’s G uide Rev . 1.01 Command No. Command Descriptions C5H: [70] [Look-up table (Gamma)] Initia l data: [7..0] = 00H D[7..0] D7 D6 D5 D4 D3 D2 D1 D0 D7 to D3: No function Al.
32/32 FV -L030 B1 User ’s G uide Rev . 1.01 Revision Histor y Rev Date Changes Note 1.00 2012/06/20 Initial Release 1.01 Updated Camera Output Ti m ing Horizontal T im ing Comm unication Protocol 20-21H SVR 78H T est patte rn 79H Pasteurizat ion Deleted F1H comm and due to test use only RICOH CO MP A NY , L TD.
An important point after buying a device Ricoh FV-L030B1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ricoh FV-L030B1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ricoh FV-L030B1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ricoh FV-L030B1 you will learn all the available features of the product, as well as information on its operation. The information that you get Ricoh FV-L030B1 will certainly help you make a decision on the purchase.
If you already are a holder of Ricoh FV-L030B1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ricoh FV-L030B1.
However, one of the most important roles played by the user manual is to help in solving problems with Ricoh FV-L030B1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ricoh FV-L030B1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
