Instruction/ maintenance manual of the product AP610N Ricoh
Go to page of 96
Paper type: Wood Fr ee 80g/m2, Paper Thickn ess=100 µ m // Page s in book=92 // P rint scale=81% Gap (when printe d at 81% scale) = Pages in book × Paper thickness / 2 = 4.
Paper type: Wood Fr ee 80g/m2, Paper Thickn ess=100 µ m // Page s in book=92 // P rint scale=81% Gap (when printe d at 81% scale) = Pages in book × Paper thickness / 2 = 4.60 0000 mm Introduction This manual contain s detailed instruc tions and notes on the o peration and use of this machine.
i TABLE OF CONTENTS Trademarks....... ..................... ..................... .......................... ..................... ............. 1 How to Read This Manual ..................... ..................... ...................... .............
ii 6. Removing Misfed Paper Removing Misfed Pa per ... ..................... .......................... ..................... ............... 69 When “Remove Misfeed Paper Tray” Appears ........ ...................... ................... 70 When “Remove Misfeed Internal Path ” Appears .
1 Trademarks Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporatio n in the U nited St ates and/o r other coun tries. IPS-PRINT Printer Language Emulation Cop yright© 1999-2000 Oak Techn olo- gy, Inc., All rights reserve d.
2 How to Read This Manual The following set of symbols is used in this manual. This symbol indicates a potentially h azardous situation that might result in death or serious injury wh en you misuse the machine without following the in- structions under this symbol.
3 1. Paper and Other Media Paper and Other Media Supported by This Printer This section describes the paper size, feed direction, and the maximum amount of paper that ca n be loaded into each paper tr ay in this printer. Note ❒ The following sym bols and termin ology are used to represent the feed directi on.
Paper and Othe r Media 4 1 • The size i s supported and indicate d on the tra y dial. Be sure to set the pa- per size dial to match the a ctual paper size loaded in the tray. • The size is supported but not indicated on the tray dial. Yo u should set the tray dial to “ p ”, and se lect the paper size with the control panel.
Paper and Ot her Media Su pported by Th is Printer 5 1 • The size is supported, but it should be set as a custom size using the control panel. The supported size may differ depend ing on the printer language you use. Set as a custom s ize setting using the control panel.
Paper and Othe r Media 6 1 • The size i s supported and indicate d on the tra y dial. Be sure to set the pa- per size dial to match the a ctual paper size loaded in the tray. • The size is supported but not indicated on the tray dial. Yo u should set the tray dial to “ p ”, and se lect the paper size with the control panel.
Paper and Ot her Media Su pported by Th is Printer 7 1 ❖ Paper weight and number of sheets to be set Note ❒ Check that the top o f the stack is not high er than the limit mark insid e the tray. ❒ The Envelope Feeder Unit requires the installation of the optional Pape r Feed Unit.
Paper and Othe r Media 8 1 Paper Recommendations Loading Paper Important ❒ Do not use ink-jet printer paper b ecause it may stick to the fusing unit and cause a paper misfeed. ❒ When printing on OHP tran sparencies that hav e a print side, load them wi th the print sid e over on th e bypass tray .
Paper Recommendations 9 1 Types of Paper and Other Media Plain Paper Thick Paper Paper thickness 60 - 105 g/m 2 (16 - 28 lb.) Printer setup Press [ Paper Input ] menu, [ Paper T ype ] , and then [ Pla in Pape r ] . Note ❒ The paper type selected using th e printer drive r overrides that selected using the control panel .
Paper and Othe r Media 10 1 OHP transparencies Envelopes Printer setup Press [ Paper Input ] menu, [ Paper T ype ] , and then [ Tran sparenc y ] on the contro l panel. Note ❒ The paper type selected using th e printer drive r overrides that selected using the control panel .
Paper Recommendations 11 1 Paper not supported by this printer Avoid using the following paper as they are not support ed by this print- er. • Paper meant for an ink-jet printer • Bent, fo lded, o.
Paper and Othe r Media 12 1 Print Area The following shows the prin t area for this printer. Be sure to set the print margins correctly by the application.
Loading P aper 13 1 Loading Paper This describes how to load paper into the paper tray and bypass tray. R CAUTION: Loading Paper in Tray 1 and the optional paper feed unit The following example explains load- ing procedure for the standard paper tray (Tray 1).
Paper and Othe r Media 14 1 D Lift the front of the tray, and t hen slide it carefully into the printer until it stops. Important ❒ Do not slide the paper tray in with force. If you do, the front and side guides might move. Reference For more information about type, size and feed direction of paper that can be loaded in the tray, see p.
Loading P aper 15 1 D Slide the catch es inwards to un- lock the tr ay. E Slide the tra y until it stops. F Return the catches t o their origi- nal positions. Important ❒ Confirm that the ca tches return to their original positions s e- curely. If they are not l ocked se- curely, paper misfeeds might occur.
Paper and Othe r Media 16 1 I Lift the front side of the tray, and then plac e it into the pr inter. Carefully slide it into the printer until it stops. Important ❒ Do not slide the paper tray in with force. If you do, the front and side guides might move.
Loading P aper 17 1 E Press the {U} or {T} key to dis- play the loaded paper si ze, and then press the { # Enter } key. After about t wo seconds, the d is- play returns to the menu. F Press the { Online } key. The initial screen appears. This completes the setting change.
Paper and Othe r Media 18 1 F Press the {U} or {T} key to set horizontal value, and then press the { # Ent er } key. Press the {T} or {U} key scrolls the value in increments of 0.1 mm. Pressing the {T} or {U} key scrolls the value in incr ements of 1 mm.
Loading P aper 19 1 D Press the {U} or {T} key to dis- play the ta rget paper tray, and then press the { # Enter } key . When the optional paper feed units are installed in the printer, [ Tray 2 ] and [ Tray 3 ] will appear de- pending on the number of the in- stalled uni ts.
Paper and Othe r Media 20 1 Specifying standard size paper for the Bypass Tray Important ❒ Shuffle the paper before loading the stack onto the tray, so multiple sheets are not fed in together. ❒ Set the size and direction of the loaded paper on the control pan el or with the printer driver.
Loading P aper 21 1 D Press the {U} or {T} key to dis- play [ Paper Input ] , and then press the { # Ent er } key. The paper selection menu appears. E Check [ Bypass Size ] appears, and then press the { # Enter } key. The paper size selection menu ap- pears.
Paper and Othe r Media 22 1 Specifying cust om size paper for the Bypass Tray Important ❒ The settings of custom sized paper that take e ffect are not t he settings made on the control panel but the settings made in the printer driv er. There is no need to change the set- tings on the contro l panel.
Loading P aper 23 1 Specifying a paper type for the Bypass Tray By selecting the paper type y ou want to load, the printer performs better. You can select from the following pa- per types: • Plain Paper, Recycl ed Paper, Spe- cial Paper, Color Paper, Letter- head, Transparency, Thick Paper.
Paper and Othe r Media 24 1 Loading Envelopes As there are many kinds of envelopes, b e s u r e t o c h e c k i f t h o s e t o b e u s e d a r e supported by this printer.
Loading P aper 25 1 C Set the envelope s ize and feed di- rection. Press the { Menu } key. The [ Menu ] screen appears on the display. D Press the {U} or {T} key to dis- play [ Paper Input ] , and then press the { # Ent er } key. The paper selection menu appears.
Paper and Othe r Media 26 1 D Push the bottom pl ate down until it locks into plac e. E Load envelopes into the enve lope feeder unit, wi th the print si de down and the fl ap on the left as shown in the ill ustration. Important ❒ Confirm that the envelope flap s are securely folded down, and that there is no air inside the en - velopes.
Loading P aper 27 1 I Press the { Menu } key. The [ Menu ] screen appears on the display. J Press the {U} or {T} key to dis- play [ Paper Input ] , and then press the { # Ent er } key. The paper selection menu appears. K Press the {U} or {T} key to dis- play [ Tray Paper Size ] , and then press the { # Enter } key.
Paper and Othe r Media 28 1 Switching between Paper Trays W h e n p a p e r o f t he s a m e s iz e i s l o ad - ed in both the standard tray and the paper feed unit (o ption), paper will be fed from the standard tray when you start printing.
29 2. Replacing Consumables and Maintenance Kit Replacing the Toner Cartridge R WARNING: R CAUTION: R CAUTION: Replace the toner cartridge if the fol- lowing message appears on the dis- play: Important ❒ Do not expose the toner cartridge to light for a long time.
Replacing Con sumables and Mai ntenance Kit 30 2 Note ❒ When handling toner cartridges, never stand them up on either end or position them upside down.
Replacing the Toner Cartri dge 31 2 E Place the toner cartr idge on a flat surface. Pull out the ta pe inside the unit horizontally while hold- ing the cartridge with one hand as shown in the ill ustration.
Replacing Con sumables and Mai ntenance Kit 32 2 Replacing the Maintenance Kit R WARNING: R CAUTION: The maintenance kit contains parts for maintaining the printer. Replace the maintenance kit if the fol- lowing message ap pears on the dis- play: Before Replacing Replace all the parts included in Maintenance Kit at the same time.
Replacing t he Maintenanc e Kit 33 2 Replacing the Friction Pad Replace all friction pad of the tray. There are two kinds of friction pads. One is for the paper tray (Tray 1), and the other are for the paper fee d unit(s) (Tray 2, 3). The following procedure shows how to replacing friction pad of the paper tray (Tray1).
Replacing Con sumables and Mai ntenance Kit 34 2 E Return the paper tray to its origi- nal position, and then remove the friction pad from the tray. Note ❒ The friction pad spring may come off. Be careful not to lose the friction pad spring. F Insert the new friction pad in the paper t ray.
Replacing t he Maintenanc e Kit 35 2 Replacing the Transfer Roller A Open the front cover by pushi ng the front cover release button. B Pull the tone r cart ridge out of the printer, while lifting the front side. Note ❒ Be sure to place the used car- tridge on the level place.
Replacing Con sumables and Mai ntenance Kit 36 2 F Insert the new transfer roller on the socket with the gear of the roller positioned on the left. Important ❒ Do not insert the roller on the back of the socket, or the printer might be damaged. ❒ Insert the metallic part of the roller on the socket.
Replacing t he Maintenanc e Kit 37 2 Replacing the Paper Feed Rollers Replace all feed rollers including the printer and th e optional paper feed unit(s).
Replacing Con sumables and Mai ntenance Kit 38 2 D While sliding the green lock lever to the left ( ), set the new roller ( ). Then return the green lock le- ver to its orig inal positi on ( ). Note ❒ Check the green lock lever se- cures the roller correctly by making sure the new roller ro- tates smoothly.
Replacing t he Maintenanc e Kit 39 2 Replacing the Fusin g Unit R CAUTION: Replacing the fusing unit A Open the rear cove r by pushing the two knobs. B Remove the rear c over in a horizon- tal directi on. C Lift the lock l evers of the fusing unit as sho wn in the il lustration.
Replacing Con sumables and Mai ntenance Kit 40 2 F Replace the new fusing unit into the printer. G Push the lock levers of the fusi ng unit down until it clicks. H Insert the rear cove r to the inside grooves on both sides of the pr int- er in a horizontal dire ction.
Replacing t he Maintenanc e Kit 41 2 B Lift the lock levers of the fusing unit as shown in the illustra tion. C Pull the fusing unit out. D Pull out the pins on both sides of the new fusing unit. E Replace the new fusi ng unit into the printer. F Push the lock levers of the fusing unit down until it cl icks.
Replacing Con sumables and Mai ntenance Kit 42 2 H Print a configuration page to con- firm that the printer works prop- erly. Reference For more information about printing the co nfiguration page , see “Test Printing”, Setup Guide. KirP4GB_Mainte-F6_FM_forPaper.
43 3. Cleaning the Printer Cautions to Take When Cleaning R WARNING: R CAUTION: Clean the printer periodically to maintain fine printing. Dr y wip e t he e xte rio r wi th a sof t c lot h. I f dr y wi pin g is not en ough , w ipe wit h a soft, wet cloth that is wrung out well.
Cleaning th e Printer 44 3 Cleaning the Friction Pad If the friction pad is dirty, a multi- feed or a misfeed might occur. In this case, clean the pad as follows: A Lift the paper tray slightly, and then pull it out until it stops. Lift the front side of the tray, an d then pull it out of the printer.
Cleaning the Paper Feed Ro ller 45 3 Cleaning the Paper Feed Roller If the paper feed roller is dirty, a mis- feed might occur. In this case, clean the roller as follows: R CAUTION: Important ❒ The following are examples of clean- ing the paper feed roller on the pa- per tr ay.
Cleaning th e Printer 46 3 E Slide the green lock lever to the left ( ), so that the paper feed roller can be rele ased ( ). F Wipe the rubber part of the roller with a soft damp cloth. Then, wipe it with a dry cloth to remove the wat er. Important ❒ Do not use chemical cleaner or organic so lvent su ch as thinne r or benzene.
Cleaning th e Registrat ion Roller 47 3 Cleaning the Registration Roller If the registration roller is dirty, a mis- feed might occur. In this case, clean the roller as follows: R WARNING: R CAUTION: Clean the registration roller if dots (caused by specks of paper stuck to the roller) appear on printed OHP transparencies.
Cleaning th e Printer 48 3 E Hold the grips of the toner car- tridge, and then insert it into th e printer until it s tops. F Lower the toner cartridg e when it touches the back. G Close the front cover by pressing the left and right side indent a- tions.
49 4. Adjusting the Printer Adjusting the Image Density You can adjust the image densit y when the print side of the page is shaded or print image is too light. Important ❒ Extreme settings may create print- outs that app ear dirty. ❒ Image density settings should be made from the application or the printer driver whenever possible.
Adjustin g the Printer 50 4 Adjusting Tray Registration You can adjust th e registration of each tray. The verti cal adjustment is used for all trays. Normally, you need not update the registrati on. But w hen the optional paper feed unit or the duplex unit is installed, updating i s useful in some cases.
Adjusting Tray Regist ration 51 4 I Press the {U} or {T} key to set the digit of the registration value (mm). Increase the value to shift the print area in the positive direction, and decrease to shift in the negative di- rection. Note ❒ Pressing the {U} or {T} key makes the value increase or de- crease by 1.
Adjustin g the Printer 52 4 KirP4GB_Mainte-F6_FM_forPaper.book Page 52 Thursday, May 12, 2005 11:48 AM.
53 5. Troubleshooting Error & Status Messages on the Control Panel This section explains what the messages that appear on th e control panel mean and what to do when a pa rticular message appears.
Troubles hooting 54 5 Hardware Problem Ethernet An error has occurred in the optional Network Interface Board. Turn the power off, and t hen on. If the message appears again, call your sales or service repres entative. Hardware Problem HDD An error has occurred in the optional Hard Disk Drive.
Error & Status Mess ages on the Con trol Panel 55 5 Hardware Problem Option RAM The printer iden tified an op- tional RAM error. Turn the power off, and then on. Re- move and re-install the optional RAM. If the message appears again, contact your sales or ser vice representative.
Troubles hooting 56 5 HDD not Installed You cannot print the sample print and the locked print jobs, because the optional Hard Disk Drive is not inst alled. Install the Hard Disk Dr ive. See “Attaching Hard Disk Drive Type 2600”, Setup Guide. Hex Dump Mode The printer is in Hex Dum p Mode.
Error & Status Mess ages on the Con trol Panel 57 5 P= XX I= XXXXXXX X Power Off On / If Error Reoccur Call Service A controller error. T he SC number ind icates the prob lem. Turn the power off, and t hen on. If the message appears again, call your sales or service repres entative.
Troubles hooting 58 5 Reset Toner Cartridge The tone r cartridge i s not set correctly. Set the toner car tridge correctl y. See p.29 “Replacing the Toner Car- tridge”. The tone r cartridg e is not set in- stalled. If the cartridge is installe d, close the front cover and turn the off power switch and then on.
Printer Does No t Print 59 5 Printer Does Not Print Possible Cause Solutions Is the power on ? Confirm that the cable is securely pl ugged into the power outl et and the printer. Turn on the power. Does the Online indicator stay on ? If not, Press the { Online } key to l ight it.
Troubles hooting 60 5 If printing stil l does not start, con tact your sales or service representa tive. Con- sult with the store wher e the printer was purchased for in formation about the location of sales or se rvice repr esentati ves. When you use the optional Bluetooth interface unit.
Printer Does No t Print 61 5 Checking the port connection When the printer is directly connected via the PC cable and the data-in indicator does not flash or light up, the method of c hecking the port connection is as fol- lows. • For a parallel port connection, po rt LPT 1 or LPT 2 should be set.
Troubles hooting 62 5 Windows XP Home Edition A Select the [ Control Panel ] window from [ Start ] on the taskbar. B Click [ Printers and Othe r Hardware ] . C Click [ Printers and Faxes ] . D Click to select the icon of the printer. Nex t, on the [ File ] me nu, click [ Pr operties ] .
Other Print ing Problems 63 5 Other Printing Problems Status Possible Causes, Descriptions, and Solu tions The print side of the page is a hazy gray. Adjust the image density. See p.49 “Adjusting the Image Density”. If paper is curled, correct it.
Troubles hooting 64 5 Multiple pages are fed through the printer at once. Clean the fr iction pad if it is dirt y. See p.44 “Cleaning the Friction P ad”. If the problem persists, set the paper the other way up, and then print it. Note ❒ This method cannot be used with the adhesive label paper.
Other Print ing Problems 65 5 If the problem cannot b e solved, contact your sa les or service represen tative. The printed i mage is di f- ferent from the image on the computer. When you use some functi ons, such as enlargement and re duction, the layout of the image might be different from that show n in the computer display.
Troubles hooting 66 5 Additional Troubleshooting Problems Solutions Strange noise is heard. If a supply was recently replaced or an option attached in the area the strange n oise is coming from, check the su pply or option is properly attached. If the strange noise persis ts, con- tact your sale s or service r epresentat ive.
Additiona l Troubl eshooting 67 5 If the machine is still not operating satisfactorily, contac t your sales or service representative. Consult with the store wher e the p rinter w as purch ased for in- formation about th e location of sales or service representatives.
Troubles hooting 68 5 KirP4GB_Mainte-F6_FM_forPaper.book Page 68 Thursday, May 12, 2005 11:48 AM.
69 6. Removing Misfed Paper Removing Misfed Paper An error message appears if a paper misf eed occurs. The err o r message gives the location of the misfeed. Important ❒ Misfed paper may be covered i n toner. Be careful not to get toner on your hands or clothes.
Removing Misfed P aper 70 6 When “Remove Misfeed Paper Tray” Appears Important ❒ Forcefully removing misfed paper may cause paper to tear and leave scraps of paper in the printe r. This might cause a misfeed and damage the printer. A Lift the paper tray slightly.
When “Re move Mis feed Internal Path” Appear s 71 6 When “Remove Misfee d Internal Path” Appears Important ❒ Forcefully removing misfed paper may cause paper to tear and leave scraps of paper in the printe r. This might cause a misfeed and damage the printer.
Removing Misfed P aper 72 6 F Close the front cover by pressing the left and right side indenta- tions. Important ❒ If paper is fed from the bypass tray, be sure to remove all the paper from the bypass tray and close it before opening the front cover.
When “Rem ove Misfeed Pa per Exit Co ver” Appears 73 6 When “Remove Misfeed Paper Exit Cover” Appears R CAUTION: Important ❒ Forcefully removing misfed paper may cause paper to tear and leave scraps of paper in the printe r. This might cause a misfeed and damage the printer.
Removing Misfed P aper 74 6 Removing misfed paper from the fusing unit A Open the rear cover by pushing the two knobs. B Remove the rear cover in a hori- zontal directio n. C Lift the lock levers of the fusing unit as shown in the illustra tion. D Pull the fusing un it out.
When “Rem ove Misfeed Pa per Exit Co ver” Appears 75 6 G Push the lock levers of the fusi ng unit down until it clicks. H Insert the rear cove r to the inside grooves on both sides of the pr int- er in a horizontal dire ction. I Close the rear cover.
Removing Misfed P aper 76 6 When “Remove Misfeed Duplex Unit” Appears R CAUTION: Important ❒ Forcefully removing misfed paper may cause paper to tear and leave scraps of paper in the duplex unit. This might cause a misfeed and damage the prin ter.
When “Remov e Misfeed Dupl ex Unit” Appears 77 6 F Close the cover of the duplex unit. Removing misfed paper inside the duplex unit A Push down th e lever on the right side of the duplex unit ( ), and then pull it out until it stops ( ). B Lift the guide board inside the duplex unit, and then remove the misfed paper.
Removing Misfed P aper 78 6 KirP4GB_Mainte-F6_FM_forPaper.book Page 78 Thursday, May 12, 2005 11:48 AM.
79 7. Appendix Moving and Transporting the Printer R CAUTION: Repack the printer in its original packing mater ials for transporting. Important ❒ Be sure to disconnect all cables from the printer before transpo rting it. ❒ The printer is a precision piece of mach i n e r y .
Appendix 80 7 Moving the Printer R CAUTION: Moving the printer in the short distance A Be sure to check the following poi nts: • The power of the printer is turned off. • The power cable is unplugged from the wall outlet. • The interface cabl e is unplugged from the printer.
Consumables 81 7 Consumables R CAUTION: Toner Cartridge *1 A4, 3% test chart Note ❒ The actual number of printed pages you get from a particular toner cartridge depends on the type and size of pape r you are using, the contents of your print images, and printing environment condi tions.
Appendix 82 7 Maintenance Kit ❖ Maintenance Kit Type 610 *1 A4, 3% test chart Note ❒ The actual number of printable pages varies depending on the image volume and density, number of p ages to be pr inted at a time, paper type and paper size used, and environmental co nditions such as temperat ure and humidity.
Specific ations 83 7 Specifications Mainframe ❖ Configuration: Desktop ❖ Print Process: Laser beam scanning & Electrophotographic printing Dual component to ner development ❖ First Print Speed: 7.
Appendix 84 7 ❖ Paper size: See p.3 “Paper and Other M edia Supported by This Printer”. ❖ Paper Weight: See p.3 “Paper and Other M edia Supported by This Printer”. ❖ Media Type: See p.9 “Types of Paper and Other Media”. ❖ Power Source: 220 - 240 V, 50/60 Hz, 4.
Specific ations 85 7 ❖ Weight: Approximately 20 kg ( 44.1 lb.) (toner cartridge and power cable included) ❖ Warm-up Time: Less than 19 seconds (23 ° C, 73F) ❖ Paper Capacity: *1 Paper weight: 60 - 105 g/m 2 (16 - 28 lb.) *2 You can load up to 10 envelopes (55 - 157 g/m 2 , 14 - 42 lb.
Appendix 86 7 Options Paper Feed Unit Type 610 ❖ Dimensions (W × D × H): 468 × 410 × 130 mm (18.4 × 14.8 × 5.1 inches) (without pins on the unit) ❖ Paper Weight: 60 - 105 g/m 2 (16 - 28 lb.) ❖ Paper Size: See p.3 “Paper and Other M edia Supported by This Printer”.
Specific ations 87 7 Memory Unit Type C 256MB ❖ Module Type: SO-DIMM (Small Outline Dual-in-line Memory Module) ❖ Memory Type: SDRAM (Synchronous Dynamic RAM) ❖ Number of Pins: 144 pins 1394 Interface Unit Type 4510 ❖ Transmission Spec.
Appendix 88 7 802.11b Interface Unit Type F ❖ Transmission Spec.: Based on IEEE 802 .11b (Wireless LAN) ❖ Protocol: TCP/IP, NetBEUI, IPX/SPX, AppleTalk Note ❒ SmartDeviceMonitor and Web Image Mon itor are supported. ❖ Data Transfer Speed: Auto select from below speed 1 Mbps, 2 Mbps, 5.
89 INDEX 1394 Interfa ce Unit Type 4510 , 87 802.11b Interfa ce Unit Type F , 88 A Additional Troubleshooting , 66 Adjusting the Image Density , 49 Adjusting Tray Registration , 50 Appendix , 79 B Blu.
90 GB GB G116-8606A S Specifications , 83 Specifying a paper type Bypass Tray , 23 Optional Paper Feed Unit , 18 Tray 1 , 18 Specifying custom size paper Bypass Tray , 22 Optional Paper Feed Unit , 17.
Paper type: Wood Fr ee 80g/m2, Paper Thickn ess=100 µ m // Page s in book=92 // P rint scale=81% Gap (when printe d at 81% scale) = Pages in book × Paper thickness / 2 = 4.60 0000 mm Introduction This manual contain s detailed instruc tions and notes on the o peration and use of this machine.
Paper type: Wood Fr ee 80g/m2, Paper Thickn ess=100 µ m // Page s in book=92 // P rint scale=81% Gap (when printe d at 81% scale) = Pages in book × Paper thickness / 2 = 4.
An important point after buying a device Ricoh AP610N (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ricoh AP610N yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ricoh AP610N - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ricoh AP610N you will learn all the available features of the product, as well as information on its operation. The information that you get Ricoh AP610N will certainly help you make a decision on the purchase.
If you already are a holder of Ricoh AP610N, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ricoh AP610N.
However, one of the most important roles played by the user manual is to help in solving problems with Ricoh AP610N. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ricoh AP610N along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
