Instruction/ maintenance manual of the product AXT-500 Audiovox
Go to page of 17
OWNER'S MANUAL Model AXT -500 500 Watt 4-Channel Bridgeable MOSFET Amplifier.
Specifications.....................................................................3 Precautions........................................................................ 4 Installation Instructions...................................................... 5 Wiring Instructions.
Input Impedance: Low-Level 10K Ohms High-Level 100 Ohms Input Sensitivity: Low-Level 200 mV - 8 V. High-Level 2V - 10 V Filter type: Selectable Full/Low-pass Crossover @ 12dB/Octave Filter Crossover: LPF 50-250 Hz (variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 30 amps.
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of the battery.
1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode.
The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using.
4. Speaker Connections Depending on the type and number of speakers used with the amplifier , wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge.
-8- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250H.
-9- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-10- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250.
-11- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-12- CAR STEREO Right Rear+ HIGH-LEVEL (SPEAKER) OUTPUTS USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT , NOT BOTH. IMPORT ANT GND GND 2CH 2CH 1CH 1CH 3CH 3CH 4CH 4CH X-OVER X-OVER 50Hz 50Hz 250Hz 250Hz 250.
-13- CAR STEREO GROUND BA TTERY FOR 12 VOL T USE ONL Y AUTO-ANTENNA LEAD GROUND MET AL SECTION OF VEHICLE EXISTING SCREW OR BOL T CLEAN P AINT , RUST , DIRT OR GREASE FROM AREA FOR GOOD CONNECTION.
-14- Power Indicator Lamps After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. If activated by a rise in emperature, the unit will resume operation after cooling of f to a normal operating range.
LPF Crossover Frequency Control This Control selects the crossover frequency when the Sub woofer Crossover Selector is in the "LPF" setting. Adjust it to the appropriate position for the characteristics and crossover frequency requirements of the speaker system with which the amplifier is being used.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
2003 Audiovox Electronics Corporation, Hauppauge, N.Y . C C Printed in Korea 128-6561 1.
An important point after buying a device Audiovox AXT-500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox AXT-500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox AXT-500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox AXT-500 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox AXT-500 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox AXT-500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox AXT-500.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox AXT-500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox AXT-500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
