Instruction/ maintenance manual of the product TQFP-120 Renesas
Go to page of 20
H8S/2655 Series TQFP-120 User System Interface Cable (HS2655ECN61H) for E6000 Emulator User’s Manual HS2655ECN61HE(C).
Cautions 1. Renesas neither warrants nor grants li censes of any rights of Renesas’s or any t hird party’s patent, copyright, t rademark, or other intel lect ual property rights for informat ion contained in this document.
i Preface Thank you for purchasing this user system interface cable (HS2655ECN61H) for the Renesas’s original mi crocomputer H8S/2655 series. The HS2655ECN61H is a user system interface cable that c.
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 4 2.1 Connecting User System Interf ace Cable to Em ulat or Station .
1 Section 1 Configuration CAUTION Use an IC149-120-043-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-120 package IC socket on the user system. Figure 1 shows the configuration of the HS2655E CN61H user system interface cable for the TFP-120 package.
Figure 1 HS2655ECN61H User System Interface Cable 2.
3 Table 1 lists t he HS2655ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2655ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Includes.
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY.
Emulator station E6000 Cable body User system interface cable Figure 2 Connecting User System Int erface Cable to Emulator Station 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part.
6 2.2.2 Soldering IC Socket After fastening, solder the IC socket for a T FP-120 package to the user system. Be sure to completely solder the leads so that the solder slo p s gently over the leads and fo rms solder fillets. (Use slightly more solder than the MCU.
Fasten the user system interface cable head to the IC socket for a TFP-120 package on the user system with t he four screws (M2 x 12 m m; with four flat washers) provi ded. Each screw should be tightened a little at a time, alternating between scre ws on opposing corners.
2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable body Cable head Remove jig Push the remove jig Removing User system Figure 4 Fastening Cable Body 8.
2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for a TFP-120 package (IC149-120-043-B5: m anufactured by YAMAICHI ELECTRONICS Co., Ltd.
2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interf ace cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10.
2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 7.
12 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head.
MCU Pin 1 IC socket (IC149-120-043-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Screws (M2 x 8 mm) with flat washers Socket cover Figure 8 Installing MCU to User System 13.
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2655 series, turn on the emulator according to the procedures described in the H8S Series E6000 Em ulator User's Manual (HS2000EPI61HE).
Section 5 Notice 1. Make sure that pin 1 on the user syst em IC socket is correct ly aligned with pin 1 on t he cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU.
6. The JP1 jumper connector is used for t esting. Do not remove t he inserted jumper pin. JP1 Figure 11 JP1 Jumper Connector 16.
An important point after buying a device Renesas TQFP-120 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Renesas TQFP-120 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Renesas TQFP-120 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Renesas TQFP-120 you will learn all the available features of the product, as well as information on its operation. The information that you get Renesas TQFP-120 will certainly help you make a decision on the purchase.
If you already are a holder of Renesas TQFP-120, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Renesas TQFP-120.
However, one of the most important roles played by the user manual is to help in solving problems with Renesas TQFP-120. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Renesas TQFP-120 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
