Instruction/ maintenance manual of the product AS 9075 Audiovox
Go to page of 15
Model AS 9075 Installation Manual Remote Start Upgrade Module Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only .
The AS-9075 Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug preheat which may be required for certain diesel vehicles, (see selectable feature #5).
Remote Start Connection WIRING THE 6 PIN MAIN POWER HARNESS: RED w/ WHITE Trace Wire: + 12 volts Battery 1 Source Connect this wire t oa+1 2V D C constant source found at the vehicle's ignition switch using the 30 Amp fuse and holder provided. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.
BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition key is turned to the to the "ON" or "RUN&.
the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled. Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch. Connect the remaining wire of the control switch to chassis ground.
This wire should be connected to the ignition input of the alarm system. The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/ unlock the doors while running under control of the remote start unit.
NOTE: These wires are typically White w/ Black trace and Violet w/ Y ellow trace, however in later model Cadillacs, they are run through an orange sleeve, and are either both Black, both Y ellow , or both White wires. Consult the factory service manual for additional information.
8 WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation.
9 NOTE: 1) When selecting Diesel operation, (Feature Five), over gasoline, the only change is to the ignition 1 circuit. When Diesel is selected, the ignition 1 circuit will power up 10 seconds before the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel engines.
10 The parking lights will flash a number of times indicating the reason for the last remote start shutdown. The light flash indications are as follows: 1 Flash 1 0 or 1 5 Minute Run Timer Expired 2 F.
11 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both.
ignition switch side of the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, i t will be necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle.
margin of safety and will prevent the vehicle with a Mechanical Neutral S tart Switch from starting in gear . AUDIOVOX ADVISES THA T YOU MAINT AIN THE F ACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C .
WIRING THE CONTROL MODULE 15 © 1998 Audiovox Corp., Hauppauge, N.Y . 1 1788 Form No. 128-5365A 2nd White.
An important point after buying a device Audiovox AS 9075 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox AS 9075 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox AS 9075 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox AS 9075 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox AS 9075 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox AS 9075, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox AS 9075.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox AS 9075. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox AS 9075 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
