Instruction/ maintenance manual of the product APS-996A Audiovox
Go to page of 20
128-6772 1 of 20 Model APS-996a Owner ’s Manual IMPORT ANT ! In order to provide you with the highest level of security to your vehicle, this system is equipped with selectable manual override circuitry . It is possible that you will need to override you security system if the transmitter becomes lost, or inoperative due to battery failure.
128-6772 2 of 20 Page 2 Protected Push Button V alet/Override Switch 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / V alet / Arming Intrusion Alert With Memory Instant Siren .
128-6772 3 of 20 Page 3 known as a code grabber , which will receive and store the signal from your keychain transmitter and re-transmit at a later time to disarm your system.
128-6772 4 of 20 Page 4 ; Parking Lights flash one time. ; Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the sys- tem detected a open entry point after the learned delay expired.
128-6772 5 of 20 Page 5 ; Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of warning tones. ; Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30 second alarm cycle.
128-6772 6 of 20 Page 6 ; Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. ; Siren will not sound.
128-6772 7 of 20 Page 7 1. Enter the vehicle and turn the ignition key to the on position. 2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The system will remain in the valet mode. 3. T o return to normal operation, press and release the pushbutton switch any time the ignition is on.
128-6772 8 of 20 NOTE: If 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code.
128-6772 9 of 20 ELIMINA TING THE NORMAL ARM / DISARM CHIRPS As explained earlier in the manual, you can eliminate the chirps selectively any time you arm or disarm the system simply by holding the ARM or DISARM button for two seconds.
128-6772 10 of 20 2. Stage 1 (Omit pre-detect) In this mode, the warn away chirps created by the lesser vibration will be deleted. If strong vibration occurs, the siren will sound. 3. Stage 2 (Omit pre & full detect) In this mode, both the pre-detect stage and the full trigger stage of the sensor are defeated.
128-6772 11 of 20 2. The Gear Selector Is In Any Gear Other Then Park. 3. The Brake Is Depressed. 4. The Safety Control Switch Is In The Off Position. W ARNING! Be certain that the vehicle is outdoors before using this or any remote vehicle starting device.
128-6772 12 of 20 the pre-programmed time (5,10,15 or 20 minutes), and then shut off. This will continue for 48 hours. NOTE: The automatic start up timer can also be initiated from the keychain transmitter . T o d o this: 1. Start the vehicle using the keychain transmitter by pressing and releasing the second channel transmitter button 2 times.
128-6772 13 of 20 Lock + Trunk/Key Buttons Lock & Option Buttons Unlock + Trunk/Key Buttons Unlock & Option Buttons Trunk/Key & Option Buttons Other Transmitter button configurations are also available.
128-6772 14 of 20 Page 14 ADDITIONAL REMOTE FUNCTION ( CHANNEL 7 ) Channel 7 is an alternate output that can be controlled by the unlock button of the transmitter or by and independent button or combination of buttons.
128-6772 15 of 20 Page 15 TRANSCEIVER ICONS AND THEIR INDICA TIONS When the Key Icon Button Has Been Operated for 3 seconds the trunk open icon will flash on the LED Screen. When the Key Icon Button is pressed 2 times in suc- cession The three puffs of smoke show on the LCD screen.
128-6772 16 of 20 Triggered and entry attempt was made to the vehicles glass, or the vehicle has been hit or bumped hard enough to cause a response from the vibration detec- tor .
128-6772 17 of 20 ADDITIONAL REMOTE FEA TURES: The two way remote control unit allows you to access status information from the vehicle, check temperature, light the display , toggle the transmitter from beep tones to vibrate mode, initiate daily start timer , and temperature start.
128-6772 18 of 20 If you require more frequent starting please refer to auto start up timer mode shown earlier in this guide. NOTE: T o insure accurate 24 Hour Start up, it is advisable to reset the start time periodically as time may drift slightly each day .
128-6772 19 of 20.
128-6772 20 of 20 © 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-6772 APS 996 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING/ACTIVE REARMING SLOW FLASHING = ARMED OF F = DISARMED ON SOLID = V ALET MODE 3 FLASH.
An important point after buying a device Audiovox APS-996A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox APS-996A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox APS-996A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox APS-996A you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox APS-996A will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox APS-996A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox APS-996A.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox APS-996A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox APS-996A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
