Instruction/ maintenance manual of the product APS-55 Audiovox
Go to page of 16
Kit Contents (1) - APS-55 Control Module (2) - 2 Button High Frequency Transmitters (1) - 3 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Six Pin Power Harness (1) - Two Pi.
The APS-55 Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications.
3 IMPORT ANT! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MUL TI PIN INPUT / OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HA VE BEEN MADE. AFTER SELECTING YOUR T ARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGA TIVE BA TTERY CABLE FROM THE VE- HICLE BA TTERY PRIOR TO MAKING ANY CONNECTIONS.
SEE NEUTRAL ST ART SAFETY TEST FOR FUR THER DET AILS. BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition ke.
WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self tapping screw and ring terminal.
the Brown w/ Black trace wire to the output of the brake light switch. If the brake light switch in the vehicle switches ground , do not use the Brown w/ Black wire; see Grey w/ Black tracer wire.
LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off.
DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine com- partment and connect to the negative side of the ignition coil.
3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay .
10 1. RF Programmable Features: Feature Selection 1 Flash 2 Flash 3 Flash 4 Flash Default 1 Run Time 5 Min. 10 Min. 15 Min. 20 Min. 10 Min. 2 Ign. 2 During Crank Off On On 3 Light Output During Run Steady Flash Steady 4 Tach Mode N A Tach Tach 5 N A NA NA NA NA NA 6 Trouble Shooting O ff On O f f 7 Door Locks 1 Sec/1 Sec 3.
11 Multi Coil Pack Adaptor: (Optional) The multi coil pack adaptor , (P/N 136B1400), is designed for use with vehicles that do not respond to single coil tach programming. Although the tach resolution of this circuit is designed to interface direct with most vehicles, there may be an occasion where the following circuit may be required.
If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire of the Audiovox Remote Start Unit. If you have a plug in enable switch, check that the two pin connector is firmly seated in the mating connector on the control module.
13 the equivalent reference wire in the vehicle you are installing the Audiovox Remote Start Unit in. 2. Connect the Cathode, (Striped) end, of a 4000 series diode to this reference wire. 3. Connect the Anode, (Non Striped) end, of the diode to one side of the Remote Start enable switch.
14 F . Connect terminal 86 of the relay to a fused +12 volt constant battery source. G. Connect terminal 87 of the relay to the Chime Module side of the previously cut wire in step D. H. Connect terminal 85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B.
15 COMPLETING THE INST ALLA TION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: 1. If you have not done so already , place the red rubber handle cover over the handle of the control switch for ease of identification.
WIRING DIAGRAM © 2000 Audiovox Electronics Corp., Hauppauge, NY 1 1788 128-5936A.
An important point after buying a device Audiovox APS-55 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox APS-55 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox APS-55 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox APS-55 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox APS-55 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox APS-55, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox APS-55.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox APS-55. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox APS-55 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
