Instruction/ maintenance manual of the product Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 Regency
Go to page of 7
P121 - P121LC/R C - P131 Zero Clear ance Direct V ent Gas Fireplace Model P121/P131-NG2 P121/P131-LP2 Fuel T ype Natural Gas Propane Minimum Supply Pressure 5” W .C. (1.25 kPa) 12” W .C. (3.00 kPa) Manifold Pressure - High 3.8” W .C. (0.95 kPa) 1 1” W .
F r aming and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. T otal facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick.
R e gency Direct V ent System (F le x) Horizontal T erminations Only These venting systems, in combination with the P121/P131 Direct V ent Gas Fireplace, have been tested and listed as a direct vent heater system by W arnock Hersey . The location of the termination cap must conform to the requirements in the V ent T erminal Locations diagram.
Rigid Pipe Adapter 1-1/2” (38mm) 45 Elbow o V enting Ar rangements - V er tical T er minations Rigid Pipe System (Propane & Natural Gas) The P121 /131 is approved for a maximum 35 ft. straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas.
V er tical V enting with Tw o (2) 90° Elbows - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V+ V1 H Maximum total pipe: length, of all sections, must not exceed 37 feet. T otal horizontal sections must not exceed 17 feet. Minimum of 1 foot between 90° elbows is required.
Horizontal V enting with One (1) 90° Elbow T wo 45° elbows = One 90° elbow Option V H Maximum total pipe: length, of all sections, must not exceed 37 feet. T otal horizontal sections must not exceed 17 feet. Minimum of 1 foot between 90° elbows is required.
Horizontal V enting with Two (2) 90° Elbows - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V H+ H1 Maximum total pipe: length, of all sections, must not exceed 37 feet. T otal horizontal sections must not exceed 15 feet. Minimum of 1 foot between 90° elbows is required.
An important point after buying a device Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 you will learn all the available features of the product, as well as information on its operation. The information that you get Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 will certainly help you make a decision on the purchase.
If you already are a holder of Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2.
However, one of the most important roles played by the user manual is to help in solving problems with Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Regency Zero Clearance Direct Vent Gas Fireplace P121/P131-LP2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
