Instruction/ maintenance manual of the product MX Excel Regency
Go to page of 14
• MX E XCEL • • C EILING F AN O WNER'S M ANUAL • WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
G ENERAL I NST ALLA TION & O PERA TION I NSTRUCTIONS I MPOR T ANT S AFEGUARDS : 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thor oughly before beginning . 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring .
Wa r n ings: • Disconnect power by removing fuse or turning off circuit breaker befor e installing the fan and/or optional lighting. Support dir ectly from building structur e.
U NPACKING Y OUR F AN 1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged.
P REP ARA TION : Ve rify you have all parts before beginning the installation. Check foam insert closely for missing par ts. Remove motor from packing. T o avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box.
I NST ALLING T HE F AN 4 This fan ha s three installati on options: I NST ALLA TION : The 3˝ DOWNROD or HUGGER methods are pr eferred if maximum headr oom is requir ed. Blades will be approximately 8-10˝ from the ceiling. Air flow will be reduced when the fan is installed using the 3˝ downr od or hugger options.
I NSTALLING THE F AN - H UGGER S TYLE NOT E: The S hook is to be used for hugger style mounting. 1. Remove the plastic trim ring from the canopy to expose the 6 mounting holes. The downrod, ball and cotter pin will not be used for this mounting (Fig. 1).
6 I NST ALLING THE F AN WITH A D OWNROD 1. Carefully suppor t fan body (motor) in its styrofoam packing with the mounting collar (wher e the wires come out) facing upward. Select the 3˝ or 6˝ (or optional extension) downr od you wish to use. 2. Remove ball from the 3” or 6˝ downr od by loosening set screw in the side of the ball.
7 I NST ALLING THE F AN WITH A D OWNROD 1. Lift ball/downrod/fan into hanger bracket opening. NOTE: The tab opposite hanger bracket opening should fit in slot on ball (Fig. 3). 2. Make wire connections, (r efer to section titled “Electrical Connections”).
8 E LECTRICAL C ONNECTIONS E LECTRICAL C ONNECTIONS : Be sure electricity is turned off at the main power box befor e wiring 1. Four wires ar e connected to the fan. Black – this is the “hot” power to run fan. White – this is the “common” power to run fan and light.
B LADE A TT ACHMENT 9 B LADE A TT ACHMENT : Fig. 5 1. Place fiber washer on scr ew . Inser t this assembly through the blade and start the scr ew into the blade arm. Repea t this procedur e without tightening the screw until all 3 scr ews have been started into the blade arm (Fig.
10 I NST ALLA TION OF R EMOV ABLE S WITCH H OUSING NOTE: Be sure the power is of f before installing. 1. Loosen the 3 side screws on switch housing hub halfway . 2. If installing light kit, carefully r emove light kit plug in bottom of switch housing.
O PERA TION 11 Tu rn on the power and check operation of the fan. The fan is controlled by the use of the fan speed pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensur e that the fan speed pull chain is pulled down fully and released each time.
5/04 Regency Ceiling Fans T HANK YOU FOR PURCHASING A R EGENCY C EILING F AN . Wr ite to us at: Regency Ceiling Fans P. O. Box 730 Fenton, MO 63026 V isit us on the W eb at: www .regencyfan.com Periodic cleaning of your new ceiling fan is about the only maintenance that is needed.
An important point after buying a device Regency MX Excel (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Regency MX Excel yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Regency MX Excel - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Regency MX Excel you will learn all the available features of the product, as well as information on its operation. The information that you get Regency MX Excel will certainly help you make a decision on the purchase.
If you already are a holder of Regency MX Excel, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Regency MX Excel.
However, one of the most important roles played by the user manual is to help in solving problems with Regency MX Excel. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Regency MX Excel along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
