Instruction/ maintenance manual of the product G36D Regency
Go to page of 44
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 918-515 MODELS: G36D-NG1 Natural Gas G36D-LP1 Propane 12/18/05 G36D Zero Clearance Direct V ent Gas Fireplace O.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 2 T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Gas Fireplace by FIREPLACE PRODUCTS INTERNA TIONAL .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 3 T ABLE OF CONTENTS OPERA TING INSTRUCTION S Operating .................................................................... 3 4 Instructions .................................................
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 4 This is a copy of the label that accompanies each G36D Zero Clearance Direct V ent Gas Fireplace. We have printed a copy of the contents here for your review.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 5 INST ALLA TION CHECKLIST 1) Chec k all clearan ces to combu stib les. Refer to the following sections: a) Locating Y our Gas Stove b) Clea.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 6 INST ALLA TION Diagram 1 This includes: 1) Clocking the appliance to ensure the correct fi ring rate (rate noted on label 26,000 Btu/h) after burning appliance for 15 minutes.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 7 MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram below: FRAMING AND FINISHING 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 8 INST ALLA TION COMBUSTIBLE MANTELS Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of unit are shown in the diagram below .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 9 "C" Screw Position: For a facing material depth of 1-1/4" (32mm), the top facing support must be reversed.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 10 INST ALLA TION EXTERIOR VENT TERMINA TION LOCA TIONS .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 1 1 VENTING UltraGlow ® UltraGlow ® UltraGlow Direct V ent System (Flex) ® Direct V ent System (Flex) ® Horizontal T erminations Only Th.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 12 INST ALLA TION FPI 946-506/P Vent Guard (Optional) 510-994 Rigid Pipe Adaptor (Must .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 13 Rigid Pipe Adaptor (Part# 510-994) Pipe Length V ertical T erminal S torm Collar (Part # 953) Flashing 943 or 943S Ceiling Firestop (Part # 963) 24" Pipe Length Adj.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 14 RIGID PIPE VENTING ARRANGEMENTS - HORIZONT AL TERMINA TIONS UltraGlow ® UltraGlow .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 15 INST ALLA TION RIGID PIPE VENTING ARRANGEMENTS - HORIZONT AL TERMINA TIONS UltraGlow ® UltraGlow ® UltraGlow DIRECT VENT SYSTEM (FLEX) .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 16 RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINA TIONS (Propane & Natural Gas) The G36D is approved for a maximum 23 ft. (7.0m) vertical, with a maximum 12 ft.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 17 INST ALLA TION The G36D is approved for a maximum 37 ft. (1 1.3m) straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas, as per the diagram 3.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 18 INST ALLA TION VERTICAL TERMINA TION WITH CO-LINEAR FLEX SYSTEM This appliance is designed to be attached to two 3" (76mm) co-linear aluminium fl ex running the full length of the chimney .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 19 INST ALLA TION VENTING ARRANGEMENTS - VERTICAL TERMINA TIONS with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagrams show the allowable vertical terminations.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 20 Diagram 4 6) The arrow on the vent cap should be pointing up. Insure that the 1-1/2" clearances to combustible materials are maintained (Diagram 4).
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 21 INST ALLA TION Diagram 3 Diagram 5 Diagram 1 Diagram 2 Note: Ap ply sea lant "Mill- Pac" to inner pip e and high temperature silicone seal- ant to outer pipe on every twist-lock joint.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 22 4) Separate the 2 halves of the wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 23 INST ALLA TION GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual s hut-off valve du r in g a n y p r es s u re testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 24 CONVERSION KIT #773-969 FROM NG T O LPG FOR G36D-1 USING SIT 820 NOV A GAS V AL VE I.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 25 INST ALLA TION 20) Replace yellow "Natural Gas" label with red "Propane" label. W A RNING! Do not overtighten the screw Recommended to grip the wrench by the short side.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 26 28) Install the 1/2" bushing to the heat shield. 30 ) Plug the DC spark generator wires to the DC Sparker . 31 ) Connect the ground wire to the DC Sparker mounting bracket.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 27 5) Position Log 02-53 across the cutouts in Logs 02-75 and 02-51 with the notch on the left side of the log fi tting into the 2nd grate tab. Cutouts 2nd Grate T ab LOG SET INST ALLA TION Read the instructions below carefully and refer to the diagrams.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 28 INST ALLA TION Log indentation Photo shows rear grate tab.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 29 10) Place the embers on the front of the burner tray in the places shown on the photos below . 1 1) T est fi re to ensure proper light off (make sure fl ame fl ows smoothly from one end of burner to the other).
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 30 Diagram 3 Use the hook to pull the spring out until you can put the hook into the slot on the bottom door bracket. Repeat for 2nd spring.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 31 Thermostat Wire T able Option 3: W ALL THERMOST A T A wall thermostat may be installed if desired, connect the wires as per the wiring diagram. Use the table below to determine the maximum wire length.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 32 WIRING DIAGRAM This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will continue to operate.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 33 120 V olt AC power is needed for the fan switch and blower . A three wire power cord is provided to be plugged into the receptacle. Unit mus t be gr ounded at all tim es. Do not cut the ground terminal off under any circumstances.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 34 OPERA TING INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 35 MAINTENANCE INSTRUCTIONS 1) Alw ays tur n off the gas valv e befor e clean ing . For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 36 MAINTENANCE 4) Make a periodic check of burner for proper position and condition. Visually check the fl ame of the burner periodi cally , making sure the fl ames are steady; not lifting or fl oating.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 37 13) Undo the pilot tube from the valve with a 7/16" wrench. 14) Undo the quick drop out thermocouple nut on the valve with a 9mm (metric) wrench. 15) Remove the Piezo ignitor wire and push button assembly .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 38 P ARTS LIST G36D MAIN ASSEMBL Y Part # Description 1) 948-253 Door Handle 2) 510-026.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 39 G36D BURNER ASSEMBL Y & LOG SET Part # Description 52) 910-190 Piezo Ignitor & Nut 53) 780-021 Gasket - V alve Access Plate NG/LP 786-574/P V alve Assy - Natural Gas 786-576/P V alve Assy - Propane 56) * V alve T ray - NG/LP 57) 910-378 V alve - S.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 40 P ARTS LIST G36D FLUSH FRONT ASSEMBL Y 131) 510-934 Flush Glass T rim (Set) - Brass .
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 41 NOTES ___________________________________________________ ___________________________________________________ ___________________________.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace ® G36D Zero Clearance Direct V ent Gas Fireplace ® 42 NOTES ___________________________________________________ __________________________.
UltraGlow ® G36D Zero Clearance Direct V ent Gas Fireplace 43 W ARRANTY UltraGlow ® UltraGlow ® UltraGlow products, are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully ® products, are designed with reliability and simplicity in mind.
UltraGlow G36D Zero Clearance Direct V ent Gas Fireplace 44 Installer: Please complete the following information Dealer Name & Address: ______________________________________________ _____________.
An important point after buying a device Regency G36D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Regency G36D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Regency G36D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Regency G36D you will learn all the available features of the product, as well as information on its operation. The information that you get Regency G36D will certainly help you make a decision on the purchase.
If you already are a holder of Regency G36D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Regency G36D.
However, one of the most important roles played by the user manual is to help in solving problems with Regency G36D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Regency G36D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
