Instruction/ maintenance manual of the product 510-994 Regency
Go to page of 10
P33 Zero Clear ance Direct V ent Gas Fireplace Model P33-NG4 P33-LP4 Fuel T ype Natural Gas Propane Minimum Supply Pressure 5” W .C. (1.25 kPa) 12” W .C. (3.00 kPa) Manifold Pressure - High 3.8” W .C. (0.95 kPa) 1 1” W .C. (2.74 kPa) Manifold Pressure - Low 1.
Model P33-NG4 w/ Contemporary Faceplate P33-LP4 w/ Contemporary Faceplate Fuel T ype Natural Gas Propane Minimum Supply Pressure 5” W .C. (1.25 kPa) 12” W .C. (3.00 kPa) Manifold Pressure - High 3.8” W .C. (0.95 kPa) 1 1” W .C. (2.74 kPa) Manifold Pressure - Low 1.
F r aming and Finishing 1) Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the fi nished surface to be fl ush with the front of the unit. T otal facing thickness can vary from 1/2” (13mm) to 1-¼” (32mm) thick.
P33 Gas Fireplace Combustible Mantels with Contemporar y F aceplate Because of the extreme heat this fi replace emits, the mantel clearances are critical. Combustible mantel clearances from top of the louvers are shown in the diagram below . Mantel may be installed anywhere in the shaded area or higher .
6-7/8" (173mm) dia. Flue pipe 4" (102mm) dia. flue pipe W all Thimble (2 pc) T ermination Cap (Part# 946-523/P) AstroCap TM spring spacer FPI Direct V ent System (Flex) Horizontal T erminati.
Rigid Pipe V enting Horizontal or V ertical T erminations V enting Ar r angements - V er tical T er minations Rigid Pipe System (Propane & Natural Gas) The P33 is approved for a maximum 40 ft. straight vertical, with Rigid Pipe vent systems for Propane and Natural Gas.
V er tical V enting with Two (2) 90° Elbo ws - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V H V+ V1 Maximum total pipe: length, of all sections, must not exceed 30 feet. T otal horizontal sections must not exceed 8 feet. Minimum of 1 foot between 90° elbows is required.
V enting Ar r angements - Horizontal T er minations This lightly shaded area of the diagram shows allowable combinations of vertical runs with horizontal terminations, using one 45° and one 90° elbow (two 45º elbows equal one 90° elbow). Note: Must use optional rigid pipe adapter (Part # 510-994) when using Rigid Pipe.
Horizontal V enting with Two (2) 90° Elbows - Initial v er tical section. T wo 45° elbows = One 90° elbow Option V H+ H1 Maximum total pipe: length, of all sections, must not exceed 30 feet. T otal horizontal sections must not exceed 8 feet. Minimum of 1 foot between 90° elbows is required.
Flex Liner Exhaust Flue A maximum of two certified joiner kits may be used per length. #948-305 35 ft (1 1m) Air Intake Co-linear DV V ertical T ermination Cap # 946-529 Co-Linea Flex Adapter with Kit.
An important point after buying a device Regency 510-994 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Regency 510-994 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Regency 510-994 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Regency 510-994 you will learn all the available features of the product, as well as information on its operation. The information that you get Regency 510-994 will certainly help you make a decision on the purchase.
If you already are a holder of Regency 510-994, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Regency 510-994.
However, one of the most important roles played by the user manual is to help in solving problems with Regency 510-994. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Regency 510-994 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
