Instruction/ maintenance manual of the product AMP-591A Audiovox
Go to page of 15
Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual Model AMP-591A 300 W att S tereo Amplifier.
INDEX Specifications .............................................................................1 Precautions ................................................................................2 Installation Instructions ...............................
HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed.
PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive ( + ) terminal of the battery.
INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode.
WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate diagrams for the system configuration you are using.
4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge.
R L LOW INPUT HPF LPF STEREO AND MIXED-MONO INPUT WIRING DIAGRAM -6- 5-PIN CONNECTOR IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. HIGH-LEVEL (SPEAKER) OUTPUTS CAR STEREO USE THIS INP.
- LEFT SPEAKER - + RIGHT SPEAKER + STEREO MOD E:2-8 OHMS MIXED-MONO MOD E:4-8 OHMS STEREO MOD E:2-8O H M S MIXED-MONO MOD E:4-8 OHMS STEREO AND MIXED-MONO OUTPUT WIRING DIAGRAM -7- AUT.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN -8- MONO (BRIDGED) INPUT WIRING DIAGRAM CAR STEREO LOW-LEVEL RCA OUTPUTS "Y" RCA TYPE SHIELDED CABLE (NOT SUPPLIED) TO 2nd AMPLIFIER IMPORTANT USE EITHER HIGH OR LOW-LEVEL INPUTS, NOT BOTH.
-9- MONO (BRIDGED) OUTPUT WIRING DIAGRAM USE THIS OUTPUTWIRING WITH INPUT WIRING ON PAGE8 AUTO-ANTENNA LEAD USE #16 GAUGE WIRE (SEE TEXT) CAR STEREO CONNECT THIS WIRE LAST EXISTING SCREW OR BOLT CLEAN.
R L LOW INPUT HPF LPF PROT PWR BASS BOOST X-OVER GAIN HI-INPUT BRIDGED LEFT LEFT RIGHT RIGHT 20A GND REM BATT POWER FUSE SPEAKER OUT -10- OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used.
-11- overload condition, the source of the overload must be found an d corrected to resume operation of the amplifier. Most overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and connections if this situation occurs and correct as necessary.
Crossover Selector 4 is in the "HPF" setting. Adjust it to the appropriate position for t he characteristics and crossover frequency requirements of the speaker system with which t he amplifier is being used. 7 Bass Boost Switch This switch is used to accentuate the bass frequencies by adding 10 dB of boost to the signal (at 50 Hz.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in mater.
An important point after buying a device Audiovox AMP-591A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox AMP-591A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox AMP-591A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox AMP-591A you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox AMP-591A will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox AMP-591A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox AMP-591A.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox AMP-591A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox AMP-591A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
