Instruction/ maintenance manual of the product SGCZ2500S RedMax
Go to page of 32
OWNER / OPERA T OR MANUAL RECIPROCA T OR T3066-93110(103) SGCZ2500S The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit.
.
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
2. Specifications ■ SGCZ2500S Overall size(LxWxH) ·························································· 76.
For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.
❲ 6 ❳ 4. For safe operation 1 . Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise.
❲ 7 ❳ b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area.
❲ 8 ❳ ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area.
❲ 9 ❳ Never place the throttle into the high speed position when starting the engine. 2. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position.
❲ 10 ❳ • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around.
❲ 11 ❳ 4. For safe operation refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank.
■ MOUNTING ENGINE (SE1) 1. Install the engine to the driveshaft so that the cylinder head and the stop switch may come on the same side. 2. Using attached four bolts, secure the connection firmly with equal force (Torque: 25in-lbs)(Torque: 2.8 N.m.).
5. Set up ❲ 13 ❳ SE4 ■ BLADE CUTTERCASE (SE4) The blade has very sharp edges. Be sure to use protective gloves whenever handling it. 1. Remove the fastening screw (long) and the lock screw (short) from the cuttercase.
• Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m(10ft) away from the fueling point before starting the engine.
container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2 . Put fuel into the fuel tank to 80% of the full capacity.
❲ 16 ❳ ■ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1 . Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.
7. Operation engine while pulling the throttle lever. ■ ADJUSTING THROTTLE CABLE • The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP5) (1) cable adjuster ■ ADJUSTING IDLING SPEED (OP6) 1.
machine control. 3 . Since the blade does not cause cut grass to wrap around the neck, you need not to stop operation to remove such wrappers. What's more, since the whole circle of the blade is available for cutting, you can move the cutting head in all directions and cut grass growing on such place difficult-to-get with conventional trimmer.
❲ 19 ❳ 8. Maintenance MA1 every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.
❲ 20 ❳ 8. Maintenance To Sharpen Blade: 1. When the corners of cutter become rounded and the cutting edges become dull, resharpen using a small disk grinder, etc. (MA2) 2 . When sharpening, offset the top and bottom blade teeth by 1/8 inches (3.125mm), as shown in the illustration.
8. Maintenance ❲ 21 ❳ • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance.
❲ 22 ❳ machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet.
❲ 23 ❳ 9. Storage • Oil the blades. • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.
❲ 24 ❳ 10. T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ c.
1 1. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
1 1. Parts list ❲ 26 ❳ Fig.1 DRIVE UNIT (S/N: 000101 and up) Fig.2 CASE UNIT (Contended with Engine) (S/N: 2842 and up).
Fig.1 DRIVE UNIT (S/N: 000101 and up) Key# Description Part Number Q'ty NOTE Key# Description Part Number Q'ty NOTE 1 MISSION ASS’Y T3065-11000 1 2• CASE COMP, rear 3805-11102 1 3 • BE.
Fig.3 ENGINE UNIT (S/N: 2842 and up) ❲ 28 ❳ 1 1. Parts list.
❲ 29 ❳ Fig.3 ENGINE UNIT (S/N: 2842 and up) Key# Description Part Number Q'ty 1 CYLINDER 4810-12111 1 2 GASKET, base 4810-12210 1 3 BOLT, M5x22 1850-12130 2 4 INSULATOR 4810-13162 1 5 GASKET,.
The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
© Printed in Japan Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratui.
An important point after buying a device RedMax SGCZ2500S (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RedMax SGCZ2500S yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RedMax SGCZ2500S - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RedMax SGCZ2500S you will learn all the available features of the product, as well as information on its operation. The information that you get RedMax SGCZ2500S will certainly help you make a decision on the purchase.
If you already are a holder of RedMax SGCZ2500S, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RedMax SGCZ2500S.
However, one of the most important roles played by the user manual is to help in solving problems with RedMax SGCZ2500S. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RedMax SGCZ2500S along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
