Instruction/ maintenance manual of the product BCZ3050SW RedMax
Go to page of 23
US-1 BCZ3050S/T/SW U S 848-JCS-93A0 (908) BCZ3050S BCZ3050T BCZ3050SW OWNER 'S/ OPERA T OR'S MANUAL BR USHCUTTERS APPLICABLE SERIAL NUMBERS : DRIVE UNIT 90200101 and up ENGINE UNIT 90200101 .
US-2 BCZ3050S/T/SW SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
US-3 BCZ3050S/T/SW U S 1. Parts location BCZ3050S BCZ3050T BCZ3050SW 1 2 3 4 5 6 6 7 8 9 17 7 7 8 9 4 2 5 3 18 10 11 12 13 14 15 16 1. Loop handle 2. Suspention point 3. Stop switch 4. Throttle cable 5. Throttle trigger 6. Shaft tube 7. Cutting attachment guard 8.
US-4 BCZ3050S/T/SW 3. W arning labels on the machine For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.
US-5 BCZ3050S/T/SW U S •A brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operater or others. It is extremely important that you read and understand the contents of this Owner's manual.
US-6 BCZ3050S/T/SW contain dangerous carbon monoxide. 10. Never to touch the spark plug or plug cord while the engine is in operation Doing so may result in being subjected to an electrical shock.
US-7 BCZ3050S/T/SW U S 5. For safe operation equipment, CLEAN UP! ■ Transport 1. Drain the fuel from the fuel tank before transporting or storing the product. 2. When hand-carrying the product, cover over the cutting part, lift up the product and carry it paying attention to the blade.
US-8 BCZ3050S/T/SW 5. For safe operation muffler, and the ignition wiring. 4. When replacing the any other part, or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.
US-9 BCZ3050S/T/SW U S 6. Set up Tighten the screws gradually by turns. ■ INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (SE1) (1) About 19 inches (48cm) (2) About 14.5 inches (37cm) ■ HIP PAD • Fix the tube by the band.
US-10 BCZ3050S/T/SW 7. Fuel ■ FUEL • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10 feet (3 m) away from the fueling point before starting the engine.
US-11 BCZ3050S/T/SW U S 7. Fuel test standard has been discontinued by API in 1995 and it no longer exists. • Gasoline/Oil mixture Storage Recommendations Store your gasoline or gasoline/oil mixture in a cool dry area in a tightly sealed approved container to limit the entry of moisture and additional air (oxygen).
US-12 BCZ3050S/T/SW 8. Operation ■ STARTING ENGINE The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine.
US-13 BCZ3050S/T/SW U S ■ CUTTING WORK (LINE HEAD USAGE) 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the cutting attachment guard in place at all times when the unit is operated.
US-14 BCZ3050S/T/SW every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.
US-15 BCZ3050S/T/SW U S 9. Maintenance .038 in 1.00mm MA4 (1) MA2 MA1-d (1) MA3 • Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury.
US-16 BCZ3050S/T/SW 9. Maintenance MA8 (1) (2) MA7 • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.
US-17 BCZ3050S/T/SW U S •W hen sharpening, removing, or reattaching the blade, be sure to wear thick, sturdy gloves and use only proper tools and equipment to prevent injury. ■ CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the object to be cut.
US-18 BCZ3050S/T/SW 12. Optional blade usage (for BCZ3050S/SW only) ■ STARTING THE ENGINE Please refer 5.For safe operation (P.6), 8.Operation (P.12). • The product is equipped with a centrifugal clutch mechanism, so the cutting attachment could rotate as soon as the engine is started.
US-19 BCZ3050S/T/SW U S d. Keep the blade sharp. A dull blade increase the chance of blade thrust. e. Avoid feeding the blade too rapidly. The blade can bounce away from material being cut if the blade is fed faster than its cutting capability. f. Cut only from your right to your left.
US-20 BCZ3050S/T/SW Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor ad.
US-21 BCZ3050S/T/SW U S The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later small off-road engine.
RedMax STANDARD LIMITED WARRANTY STATEMENT ALL Products Sold on or after 1/01/2009 All RedMax Brand Products RedMax Limited Warranty, provides to the ORIGINAL retail purchaser that this RedMax product is free from DEFECTS in MATERIAL and WORKMANSHIP under normal use and maintenance from the date of retail purchase.
Engine Failures caused by operating engines on gasoline with octane rating lower than 89 are not covered by the RedMax Two-Stroke engine warranty. (Emission related parts only are covered for two years, regardless of two-stroke oil used, per the statement listed in the EPA or California Emission Defect Warranty Explanation.
An important point after buying a device RedMax BCZ3050SW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought RedMax BCZ3050SW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data RedMax BCZ3050SW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, RedMax BCZ3050SW you will learn all the available features of the product, as well as information on its operation. The information that you get RedMax BCZ3050SW will certainly help you make a decision on the purchase.
If you already are a holder of RedMax BCZ3050SW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime RedMax BCZ3050SW.
However, one of the most important roles played by the user manual is to help in solving problems with RedMax BCZ3050SW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device RedMax BCZ3050SW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
