Instruction/ maintenance manual of the product AA-9300 Audiovox
Go to page of 20
Model AA-9300 ACTIVE REMOTE CONTROL AUTO SECURITY SYSTEM WITH VOICE WARNING SYSTEM & BUILT IN 2 - STAGE SHOCK SENSOR INSTALLATION GUIDE & OWNER’S MANUAL SISTEMA DE SEGURIDAD ACTIVO PARA AUTO.
INTRODUCTION Your new AA-9300 Automotive Security System has been de- signed with many advanced fea- tures that will help to ensure the safety of your vehicle and it’s contents. Taking a few moments to read this manual will provide you with important information required to take advantage of the system’s full potential.
MOUNTING THE COMPONENTS 1. Mounting The Siren Con- trol Module Select a flat, metal surface within the engine compartment, but not on the engine, for mounting the siren control mod- ule. Keep in mind that the horn end must be facing down to prevent water from entering the module.
B. Pass the L.E.D. wires through the hole from the front of the panel, and press the body of the L.E.D. into the hole until fully seated. WIRING THE SYSTEM Making the connections to the vehicle, as described in this wiring section, may be beyond the technical abilities of the average consumer.
Page 3 can result in damage to wires from sharp metal edges, and an eventual failure of the secu- rity system. 2. Connecting the RED Wire Locate the courtesy lamp fuse. Both sides of the fuse will indicate + 12 Volts on the logic probe while the fuse is plugged in.
arming button on each trans- mitter, which will result in the appropriate “ ARMED “ or “ DISARMED “ indication from the siren module. IMPORTANT ! If only one trans- mitter is operating, repeat the programming procedure. Once the harness connector is plugged in, you have only 15 seconds in which to program both transmit- ters.
Page 5 will not trigger the system. This loop wire should be cut only if you want to protect the vehicle from sudden impacts to the glass or body panels, but do not want the alarm to trigger when a door has been opened.
Page 6 Printed in Taiwan Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 Form No. 128-4435 RED SPLICE TO +12V CONSTANT IN VEHICLE'S FUSEBOX DARK BLUE SIREN MOD- ULE GREEN, WHITE AND BLUE WIRE LOOPS BLACK THIN BLACK ANTENNA WIRE L.
Page 7 MODULE DE LA SIRÈNE BOULONS À TÊTE HEXAGONALE DE 0, 95 (3/ 8") DE LONG VIS DE 1,9 CM (3/ 4") DE LONG RONDEL LE DE BLOCAGE FENDUE D.
A B Page 8 FIL ROUGE CONNECTER AU FIL PAR UNE ÉPISSURE ET ENROULER DU RUBAN ISOLANT ÉLECTRIQUE AUTOUR DE LA CONNEXION FUSIBLE DESLAMPES DE SER- VICE (PORTES, PLAFONNIER) COFFRET ÀFUSIBLES BORNE EN DOUILLE DE FUSIBLE (NON COM- PRISE) BORNE NÉGATIVE FIL NOIR MODULE DE SIRÈNE 2.
Page 9 ATTENTION! Si un seul transmetteur fonctionne, il faut recommencer l’opération de programmation. Une fois que le connecteur du faisceau est enfiché, on dispose de 15 secondes seulement pour pro- grammer les deux transmetteurs. Ce créneau de courte durée est nécessaire pour assurer un haut niveau de sécurité.
Page 10 redonne au détecteur de vibra- tions sa sensibilité opérationnelle normale. 6. Télécommande du système anti-panique L’alarme peut être activée à l’aide du transmetteur de porte- clés pour attirer l’attention sur votre véhicule au cours d’une situation d’urgence.
Page 11 DÉPANNAGE: Symptôme: La sirène n’émet aucun son au moment où l’on branche le faisceau de conducteurs. Vérification: A. Vérifier que le fusible placé sur le fil ROUGE venant du module de commande de la sirène soit en bon état. Le remplacer s’il a sauté.
Page 12 Printed in Taiwan Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 Form No. 128-4435 MODULE DE LA SIRÈNE FILS EN BOUCLE, VERT, BLANC ET BLEU BLEU BLEU ROUGE D.
Page 13 INSTALACION DE LOS COMPONENTES 1. Instalación del módulo de control de la sirena Seleccione una superficie metálica plana dentro del compartimiento del motor, pero no sobre el motor, para efectuar la instalación del módulo de control de la sirena.
CAJA DE FUSIBLES A B Page 14 A B CABLE ROJO TERMINAL NEGATIVO 2. Conexión del cable ROJO Ubique la luz de posición auxiliar. Ambos lados del fusible marcarán 12+ voltios en el medidor lógico cuando el fusible esté conectado. Quite el fusible y pruebe los contactos donde se enchufa el mismo.
Page 15 TERMINACION DE LA INSTALACION Notará que hay (4) cables adicionales que salen directamente de la salida de goma para cables del módulo de control de la sirena, los que no forman parte del arnés princi- pal. Estos cables se usan para adaptar la instalación a las necesidades personales y son necesarios en algunos vehículos.
Page 16 de aproximadamente seis segundos, la función de detección de choque del sistema se activará. El circuito de detección de voltaje comenzará su cuenta regresiva, y después de aproximadamente tres minutos, al abrirse una puerta activada por las luces se encenderá la alarma.
Page 17 levante con cuidado la tapa superior (del lado del botón) para quitarla del transmisor. B. Saque la pila descargada, fijándose en la orientación de los contacto s+y-y descártela como corresponda. C. Instale la pila nueva, teniendo la precaución de colocar los contacto s+y- en la posición correcta.
Printed in Taiwan Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 Form No. 128-4435 L.E.D. Page 18 L.E.D. CABLE DELGADO NEGRO PARA LA ANTENA MODULO DE LA SIRENA NEGRO CONEXION A TIERRA .
An important point after buying a device Audiovox AA-9300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox AA-9300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox AA-9300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox AA-9300 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox AA-9300 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox AA-9300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox AA-9300.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox AA-9300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox AA-9300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
