Instruction/ maintenance manual of the product 1181293 Audiovox
Go to page of 12
INSTALLATION INSTRUCTIONS FOR 50 - 0210F - 002 SERIES 1181291 50 - 0210F - 003 SERIES 1181292 50 - 0210F - 004 SERIES 1181293 SUBURBAN OVERHEAD CONSOLE for use with FLIPDOWN VIDEO SYSTEM These instructions are intended for use only by experienced professionals in the automotive customizing business.
2 MATERIALS PROVIDED FOR INSTALLATION: ITEM Description QTY 1 SCREW, # 8 X 3/4" HWH ,TEK,Z1 4 2 SCREW, # 8 X 2 1/2" PFH ,ZII 3 3 SCREW, # 8 X 1 1/4" PWH ,BZ 4 4 CONSOLE 1 5 MOUNTING BRA.
3 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. compartment console currently mounted to inner roof of v ehicle. Remove (1) one # 8 X 1 3/4" screw from recess in front of console near rear view mirror. Pull front of O.E.M. console down to access wiring.
4 3. Discard trim ring. See Figure 3. Using a razor knife, carefully trim the (10) ten plastic pins flush with the shoulder. See Figure 4. FIGURE 3 FIGURE 4.
5 4. Remove OEM dome light and rear air conditioning control head. Disconnect wiring and set control head aside in a safe place. Remove the OEM ground screw near the center dome light assembly if applicable. See Figure 5. 5. Cut the headliner material between dome light opening and the front openings for OEM pod retainer arms.
6 6. Install the rear mounting bracket (item 5 pg 2 ) in the O.E.M. dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area.
7 8. If vehicle is equipped with an electronic compass, unsnap the wire harness clip and relocate toward center of vehicle. See Fig ure 9. 9. Remove and retain the two ( 2 ) door scuff plates on driver’s side.
8 10. Remove and retain the handle which mounts to top of the “B” pillar. 11. Unsnap the cover from upper and lower mo unting bracket for seat belt. Remove and retain TORX head bolt and bracket. Carefully pull panel away from side of vehicle. Unsnap upper door trim from headliner and lay aside.
9 14. Route all accessory wiring, video and audio cables, and any other added component requirements to their respective places in the vehicle. Refer to component installation instructions for wiring diagrams.
10 II. PREPARATION OF CONSOLE FOR INSTALLATION 1. Position the O.E.M. console in the front recess area of the new console (item 4 pg 2 ). Carefully fit the two together, aligning the rear compartment hinge arms through the slots in the recess pocket area.
11 IV. INSTALLATION OF OVERHEAD CONSOLE. Caution: Do not overtighten screws. Use extra support for the console until secured to the vehicle. Failure to do so may cause damage to console or installed components. 1. Cons truct a jumper harness that will connect the vehicle’s dome light wires to the lights in the console and video system.
12 7. Release video screen from locked position. Lower video screen to viewing position for a ccess to mounting locations in top of video system housing. 8. Raise video system into approximate position and connect all wiring to components. Route video cable through hole in mounting bracket.
An important point after buying a device Audiovox 1181293 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Audiovox 1181293 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Audiovox 1181293 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Audiovox 1181293 you will learn all the available features of the product, as well as information on its operation. The information that you get Audiovox 1181293 will certainly help you make a decision on the purchase.
If you already are a holder of Audiovox 1181293, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Audiovox 1181293.
However, one of the most important roles played by the user manual is to help in solving problems with Audiovox 1181293. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Audiovox 1181293 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
