Instruction/ maintenance manual of the product 300001-SL Razor
Go to page of 20
OW NE RS M AN UA L Read and understand this e ntire manual before riding! Electric-P ower ed Go Kart Item Number 300001-SL ®.
NOTE: This manual contains many “Warnings” and “Cautions” concerning the consequences of failing to maintain, inspect or properly use your Ground Force. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such a warning is mentioned.
• Always check and obey any loacl laws or regulations which may affect the locations where the Ground Force may be used on public property . The Ground Force is meant to be used only in controlled environments free of potential traffic hazards, and not on public streets or side - walks.
NOTE: Do not activate the speed control on the setting wheel unless you are in a safe, outdoor environment. Use this product only in areas free of potential traffic hazards and not on public streets or sidewalks. W ARNING: REGARDING USE OF NON-RAZOR PRODUCTS WITH YOUR RAZOR GROUND FORCE.
W ARNING: Failing to properly adjust and tighten the screws, nuts and bolts that affix the steering wheel and seat can cause you to lose control and c rash.
T ighten securely . Position the tie-rod control arm onto the steering axle as shown in Figure 3a and install the washers and fixing bolt. Using a 10 mm wrench, tighten securely .
❏ 2 D. Optional attaching the seat with seat belt assembly . Locate the four (4) long seat attachment screw and seat-belt assembly in the parts bag. Position the seat over the frame and align it with the holes in the frame. Position the seat-belt anchors with the lap/shoulder assem- bly on the left side and the receiver latch on right side.
Figure 6a Figure 6b W ARNING: Practice in an open area free from obstacles until you are famil- iar with the brake function. A void skidding to a stop as this can cause you to lose control as well as cause damage in the rear tires. ❏ 2 F . Charging the battery prior to use.
❏ 2 G. Circuit breaker . The circuit breaker (next to charger input port in Figure 7a) will automatically shut off the power to the motor in the event an overload condition is placed on the motor . An excessive overload, such as too heavy a driver or too steep a hill, could cause the motor to overheat.
❏ 4 A. ADJUSTING THE BEL T . The circuit breaker (next to charger input port in Figure 7a) will automatically shut off the power to the motor in the event an overload condition is placed on the motor . An excessive overload, such as too heavy a driver or to NOTE: T urn power switch off before maintenance procedures.
❏ 4 B. WHEEL REMOV AL PROCEDURE. Occasionally the wheels need to be replaced when worn out. The front and rear wheels are iden- tical and can be interchanged. The only difference is how the wheels at- tach. The rear wheels are keyed to the rear axle, while the front wheels have bearings (608ZZ = standard skateboard bearings).
4B-3.) T o replace a rear wheel, make sure the keys are properly seated in the axle and aligned with the key ways in the wheel (Figure 11). T ighten the self-locking nut securely . NOTE: The razor logo on the tread must face out. ❏ 4 C. REPLACING THE BEL T .
Figure 12a Figure 12b 4C-4.) Remove the brake guard and, using the small Allen key , loosen setscrew to release the brake drum. This may or may not require the loosening of the brake cable to gain access to the fixing screw . Loosen the drive pulley in the same manner .
5. SAFETY THE FOLLOWING RECOMMENDA TIONS ARE EXPECTED FROM: ASTM F1928-98, “ST ANDARD SAFETY GUIDE FOR CONSUMER RECREA TIONAL Y USE OF FUN-CARTS” Go kart shall not be operated with any modifications to the kart or it’ s components.
6. ADDITIONAL RAZOR SAFETY WARN INGS W ARNING: Maintain a hold on the steering wheel at all times. W ARNING : Never use near steps or swimming pools. W ARNING : T raffic can be fatal.
7. ILLUSTRA TED P ARTS BREAKDOWN See Figure 14 (Specifications and parts list subject to change without notice) ITEM# DESCRIPTION QUANTITY 1 Wheel 2 Pindle, right 3 Bearing, 608ZZ 8x22 4 T ie-rod 5 B.
ILLUSTRA TED P AR TS BREAKDOWN Figure 14.
8. RAZOR LIMITED WARRANTY & REGISTRA TION The manufacturer warranties this product to be free of manufactur - ing defects for a period of 90 days from date of purchase.
SB 1918 (CALIFORNIA) DECLARA TION: YOUR INSURANCE POLICIES MA Y NOT PROVIDE COVERAGE FOR ACCIDENTS INVOL VING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE.
IMPORT ANT! If your Razor has a problem call Razor USA toll free (866) 467-2967 QUESTIONS: Please read the owner’ s manual thoroughly . If you still have questions, check our website for updates and contact information.
An important point after buying a device Razor 300001-SL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Razor 300001-SL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Razor 300001-SL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Razor 300001-SL you will learn all the available features of the product, as well as information on its operation. The information that you get Razor 300001-SL will certainly help you make a decision on the purchase.
If you already are a holder of Razor 300001-SL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Razor 300001-SL.
However, one of the most important roles played by the user manual is to help in solving problems with Razor 300001-SL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Razor 300001-SL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
