Instruction/ maintenance manual of the product CLAHDC90BC Rangemaster
Go to page of 16
Users Guide & Installation Instructions.
IMPORT ANT SAFETY INFORMA TION Installation Page 2 Child Safety 2 Maintenance and Service 3 YOUR APPLIANCE 4 OPERA TING INSTRUCTIONS Cooker Hood Controls 4 Worktop Lighting 4 Fan 4 T o Operate 5 Recir.
• INST ALLA TION • Any installation work must be underaken by a qualified electrician or a competent person. • This hood must be installed in accordance with the installation instructions and all measurements must be adhered to.
• MAINTENANCE AND SERVICE • This appliance can be a hazard if the grease filters and charcoal filters are not cleaned and replaced as recommended. • Always insist on genuine RANGEmaster spare parts. • Under no circumstances should you attempt to repair the appliance yourself.
The chimney hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air . COOKER HOOD CONTROLS The chimney hood functions are controlled by three manual slide switches located on the right, on the underside of the canopy .
TO OPERA TE Select the required fan speed and light if required. RECIRCULA TION In the recirculation mode contaminated air enters the chimney hood through the grease filter cassettes. The air is cleaned by the charcoal filters and leaves through the grilles in either side of the chimney stack.
Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply . CLEANING We recommend the chimney hood is cleaned using a damp cloth wrung out in warm soapy water using a mild liquid household cleaner . Never use excessive amounts of water when cleaning, in particular around the control panel.
CHARCOAL FIL TERS (2) In the recirulation mode the activated charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned or regenerated and must be replaced every four months, or more frequently if the hood is used consistently over 4 hours per day .
TECHNICAL INFORMA TION DIMENSIONS CANOPY : Height 240mm Width (60cm version) 598mm (90cm version) 898mm (120cm version) 1 198mm Depth 490mm CHIMNEY : Height (Upper Section) 415mm (Lower Section) 560mm.
ELECTRICAL CONNECTION THIS APPLIANCE MUST BE EARTHED ELECTRICAL REQUIREMENTS Any permanent electrical installation must comply with the latest I.E.E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e.
INST ALLA TION REQUIREMENTS Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air .
INST ALLING THE CHIMNEY HOOD CLEARANCE HEIGHTS The chimney hood is designed to be fitted over a cooking appliance. A minimum clearance height of 650mm (25˚ins) is required when installed above a built-in electric hob, or 700mm (27˚ins) when installed above a built-in gas hob.
Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). FITTING THE CANOPY HOOD 1. Rotate the adjusting screws (R) on the canopy (C) to about halfway .
RECIRCULA TION If you are using the hood for recirculation, ensure the charcoal filters are in position following the instructions contained in the section “T o Remove/Replace the Charcoal Filters”. Note: When the hood is used in the recirculation mode ensure that the plate (T) has been fixed into the lower chimney section.
INST ALLING THE CHIMNEY HOOD FITTING THE FRONT RAIL These instructions apply to models as follows: - CLAHDC60BB/ CLAHDC90BB/, CLAHDC90BC/ CLAHDC120BB/, CLAHDC120BC/ Do not fit the front rail until the chimney hood is mounted on the wall. 1. Use a 4mm Allen key to fix the mounting brackets to the front of the canopy using the screws provided.
4329641 02 020412.
An important point after buying a device Rangemaster CLAHDC90BC (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Rangemaster CLAHDC90BC yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Rangemaster CLAHDC90BC - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Rangemaster CLAHDC90BC you will learn all the available features of the product, as well as information on its operation. The information that you get Rangemaster CLAHDC90BC will certainly help you make a decision on the purchase.
If you already are a holder of Rangemaster CLAHDC90BC, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Rangemaster CLAHDC90BC.
However, one of the most important roles played by the user manual is to help in solving problems with Rangemaster CLAHDC90BC. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Rangemaster CLAHDC90BC along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
