Instruction/ maintenance manual of the product HPR151W QSC Audio
Go to page of 20
1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA Main Number (714) 75 4-6175 or toll free (USA only) (800) 854-407 9 Customer Service(714) 957-71 50 or toll free (USA only) (800) 772-2834 HPR Series Po.
2 Important Safety Precautions & Explanation of Symbols Install in accordance with QSC Audio Product's instructions and under the superv ision of a licensed Professional Engineer . WAR N IN G! CAUTION: TO REDUCE THE RISK OF ELECTR IC SHOCK, DO NOT REMOVE THE COVER.
3 Introduction Congratulations and thank you for your purchase of this profes sional, powered loudspeaker product. T o get the most from your in vest- ment, we recommend you review all the information provided in this User Manual.
4 HPR151W Features HPR181W Features 1- Pole Cup 4- Power Amplifier 2- Handles (2 each) 5- Slip-resistant Feet (4 each) 3- Grill 6- Casters (HPR181W only) Full Range Amplifier Detail Subwoofer Amplifie.
5 Installation HPR152F WARNING! Do not use a loudspeaker suppo rt pole longer than 26” (660mm) when supported by the HPR151W or HPR1 81W subwoofer . Do not rig, fly or suspend this loudspeaker produ.
6 AC Mains Connect AC power to the IEC socket on the back of the amplifier by locating the IEC connector -end of the AC power cord and inserting it fully into the IEC inlet on the power amplifier module. NOTE: T urn off the AC power switch before connecting AC power .
7 1= shield (ground) 3= jumper to pin 1 2= plus (+) Input Connections (continued) HPR152F and HPR153F: Insert the male XLR input into the jack marked FULL RANGE LINE IN. Ensure the connector is fully seated. HPR151W and HPR181W: Insert the left channel’ s XL R input into the left channel’ s (L) FULL RANGE LINE IN connector .
8 Output Connections (continued) HPR151W and HPR181W FULL RANGE LINE OUT : Use the outputs marked FULL RANGE LINE OUT (Left and/or Right) when connecting to down-stream powered loudspeakers which accept full-range audio or have their own filtering.
9 100 Hertz Low-Cut Filter Sw itch (HPR152F and HPR153F) Below the LED indicators is a small recessed slide-switch that enables or disables a 100 Hertz low-cut filter . Filter OFF (Full Range) T urn the filter OFF when using without subwoofers or dedicated low-frequency enclosures.
10 SIGNAL Indicator LED The green SIGNAL indicator alerts the user to the p resence of an input signal to the HPR loud- speaker . Normal Indication The green SIGNAL indicator illuminates when the input signal exceeds -25 dB. If No Indication Check Gain settings and increase gain if necessary .
11 Application Example #1 This example shows a two-channel (stereo) setup utilizing two top-boxes. Audio signals for the Left and Right channels are supplied by the mixer console. This signal source can be just about any variable-output level audio source, such as DJ mixers, profes- sional CD players, or computer -based audio signal sources.
12 Application Example #2 This example shows a two-channel (stereo) setup utilizing one subwoofer and two top-boxes. Audio signals for the Left and Right channels are supplied by the mixer console.
13 Application Example #3 This example shows a two-channel (stereo) setup utiliz- ing two subwoofers and two top-boxes. Audio signals for the Left and Right channels are supplied by the mixer console.
14 Application Example #4 hookup diagram. Use only high-quality balanced cables for interconnecting the audio equipment. Ensure the top-boxes have their 100 Hz LOW-CU T FIL TER switched on when connect ing to the subwoofer’ s FULL RANGE LINE OUT as a s ignal source.
15 Dimensions, HPR152F Dimensions, HPR153F.
16 Dimensions, HPR151W Dimensions, HPR181W.
17 Specifications, Full Range Models HPR152F HPR153F Frequency Response, ±6dB 53-18k Hz 42-19k Hz Frequency Range, -10dB limit 50-20k Hz 38-20k Hz Maximum Peak SPL 135dB 133dB Nominal coverage, H x V 90°x60° 90°x40° Directivity Index 9.4 11.1 Directivity Factor 8.
18 Specifications, Su bwoofer Models HPR151W HPR181W Frequency Response, ± 6dB 47-110 Hz 42-110 Hz Frequency Range, -10dB limit 43-140 Hz 39-140 Hz Maximum Peak SPL 133dB 134dB Nominal coverage, H x .
19 Notes:.
W arranty (USA only; other countries , see your dealer or distri butor) Disclaimer QSC Audio Products, Inc. is not liable for any damage to amplifiers or any other equipment that is caused by negligence or impr oper installation and/or use of this loudspeaker product.
An important point after buying a device QSC Audio HPR151W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought QSC Audio HPR151W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data QSC Audio HPR151W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, QSC Audio HPR151W you will learn all the available features of the product, as well as information on its operation. The information that you get QSC Audio HPR151W will certainly help you make a decision on the purchase.
If you already are a holder of QSC Audio HPR151W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime QSC Audio HPR151W.
However, one of the most important roles played by the user manual is to help in solving problems with QSC Audio HPR151W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device QSC Audio HPR151W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
