Instruction/ maintenance manual of the product 59244-00 A Q-Logic
Go to page of 8
59244-00 A 1 *59244-00 A* Simplify A SANbox 9000 ™ Series Chassis Replacement Guide WARNING!! This guide describes the procedure for one person to replace a SANbox 9000 Series chas- sis. It involves removing bla des while the switch is in the rack, an d then removing the empty chassis.
SANbox 9000 ™ Series Chassis Rep lacement Gu ide 2 59244-00 A A Backup the Switch Configuration Create a backup of the switch configuratio n if one does not already exist and uploa d it from the switch to the management wo rkstation. Open a T elnet session and enter the Config Backup command to create the file on the switch.
SANbox 9000 ™ Series Chassis Replacement Guid e 59244-00 A 3 A Disconnect Ethernet and Serial Cables Disconnect Ethernet cables f rom CPU blades and the Maintenance Panel. Disconnect HyperS tacking cables fro m the CPU blades. Disconnect Fibre Channel Port Cables Label I/O blades by slot number .
SANbox 9000 ™ Series Chassis Rep lacement Gu ide 4 59244-00 A A Remove Power Supply Blades WARNING!! The Power Supply blade faceplate and internal surfaces can become very hot. Handle with care. Rotate the la tch to the full open po sition. Pull the Power Supply blade by the latch to disengage the blade from the mid plane connector .
SANbox 9000 ™ Series Chassis Replacement Guid e 59244-00 A 5 A Remove Chassis from the Rack Using a crosshead screw driver , remove the screws that secure the chassis to the rack. Slide the chassis out of the rack. Slide the chassis out of the ca binet until the rail latches drop down to stop the chassis.
SANbox 9000 ™ Series Chassis Rep lacement Gu ide 6 59244-00 A A Inst all New Chassis in the Rack Slide the new chassis into the cabinet rails. Fasten the switch rails to the cabinet rails with two screws. 1. Screws Reinst all CPU Blades Install the CPU blad es in slots CPU0 and CPU1 of the new chassis according to the labels on the CPU blades.
SANbox 9000 ™ Series Chassis Replacement Guid e 59244-00 A 7 A Reinst all Power Supply Blades NOTE Power Supply blade inst allation is easier when installe d af ter the Fan blade below it. Open the Power Supply blade latch and slide the blade into the chassis until it con tact s the midplane co nnector .
SANbox 9000 ™ Series Chassis Rep lacement Gu ide 8 59244-00 A Copyright© 2007 QLogic Corporation. SANbox is a trademark of QLogic Corporation A Observe Heartbeat LED Observe the Heartbeat LED on the CPU blade.
An important point after buying a device Q-Logic 59244-00 A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Q-Logic 59244-00 A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Q-Logic 59244-00 A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Q-Logic 59244-00 A you will learn all the available features of the product, as well as information on its operation. The information that you get Q-Logic 59244-00 A will certainly help you make a decision on the purchase.
If you already are a holder of Q-Logic 59244-00 A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Q-Logic 59244-00 A.
However, one of the most important roles played by the user manual is to help in solving problems with Q-Logic 59244-00 A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Q-Logic 59244-00 A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
